Thanks again for leading me to this video on the Hybrid install. I liked the light show at the end of the video and it really looked brighter. In real time, when facing the car, do those 35w lights have the same glow of the headlights? I like when both match and not look like one of my past cars did where the headlights were halogen and the fog lights LED. I am looking for a uniformed look.
I drove my CRV for the first time at night in the rain speeding to work on the highway. No lie, i found visibility to be very limited. I think ill need to install these too.
Very nice installation. I ordered the kit plus the sensor relocator kit. Once the sensor is relocated, how do I get the sensor wire connector attached to the sensor ? Do I need to cut some of the plastic housing away ?
Please tell me how the side view looks like ? I have a 15% tint... at night I cannot see where I'm turning, habe to open window I really need a fog lights so I can see my sides where im turning into ! Does this fog lights provide good side coverage ?? Thank you.
@IvanRossS, it's good enough, but it the further it projects, the wider the beam spreads. They are very bright, so they should be fine for what you need them for. Just remember to aim them properly as they will need adjustment when installed.
Can the parking sensor be placed above in the body colored area instead? I see in some photos it can be. How would you do that? Do you need a body colored sensor?
@xulisvoosmuas yes. It can be placed in the bumper as you see in the pictures. Also, yes, you would need the body colored sensor, which is not available in the U.S. you would also need the hole punch tool to make the new hole.
@promotionelista2780 I'm really not sure. I think it is tho. The sensors on the crv is 18.5mm. I had to make the hole a bit bigger to fit the oem sensors
Just got the kit. Do the light bulbs not flush along the plastic trim pieces? Any recommendation on the aiming of the fog light, like the setting of it?
@parthpatel6251 No, they don't. The adjustment is on the side. Adjust them all the way down, then check it, and if they are too low, bring them u up a tad bit. Just not too high where it's blinding to on coming traffic
I could not get the radar sensors to fit into the retaining brackets included in MIkstore's sensor relocation kit. Did you have to modify them? The factory retainers are different and have slots in them for the ribs on the sensors.
Did you install the 35W fog lamps or the 40W projectors lamps? Also, after you moved the parking sensors, how well do they operate ?Are they same as before?
@@RTI876 with the 35 W is it projector lamp or reflector lamp? I am guessing the 35 W comes with a ballast to plug in so it can lower that much Watts, correct?
Just had these installed. Seems like the left one is put in wrong and the light is facing up not down towards the grown like the right one. Do you think this is possible or is it defective? Left one is illuminating upwards like high beams instead of downwards!
@gamblersstory9081 the adjustment is on the side of the light fixture facing down. You need an allen key to perform the adjustment. The area is at the bottom
Thank you. I got the 40w amber projector and I honestly think it just too bright and blinding. I think the glare is caused by the beam hitting the bottom housing and reflecting. I think it’s a design flaw. For the 35w you installed, is it very bright for oncoming cars? I’m thinking about switching up to the 35w. Thanks
@joshuabob7302 I'm not sure where they came from. I'm thinking about rewiring it tho. I'm gonna connect it to the fuse box. I'll put out an updated video as soon as I get it done
@nahlho1807 I didn't buy the kit. It was sponsored, and I installed it myself. I think it will cost about $400 for everything tho... I'm not sure. I do have the lights for sale, not including the stalk. $150
@@RTI876 When purchasing the fog lights from the link, do I get the "Fog Lamp Kit - Ultra White 35W" or the "Fog Projector Kit - Ultra White 40W"? I want to get the exact ones from your video. Thanks.
@donwildermuth4347 if you were paying attention! you would realize their is no talking in the video! Just subtitles!!. Watch the other video for the detailed installation!!!
![I.N "HALLUCINATION" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/n5B5q1Hwt_U/mqdefault.jpg)
![Felix "Unfair" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/Oswujxm2Ag0/mqdefault.jpg)
You certainly know what you are doing ! Looks great.
@jackg.8600 Thank you. I appreciate it
Thanks again for leading me to this video on the Hybrid install. I liked the light show at the end of the video and it really looked brighter. In real time, when facing the car, do those 35w lights have the same glow of the headlights? I like when both match and not look like one of my past cars did where the headlights were halogen and the fog lights LED. I am looking for a uniformed look.
@mlawrence2991 They are LED, so they will be uniform🙂
@@RTI876 thanks
I drove my CRV for the first time at night in the rain speeding to work on the highway. No lie, i found visibility to be very limited. I think ill need to install these too.
@@lionintu you should!
Awesome video thank you! Any chance you could make a video on how to install the Honda heating steering wheel? Dealers want 800 to install…no thanks
@Rx-tn7mi i would but the steering wheel would have to be sponsored 🙂
Very nice installation. I ordered the kit plus the sensor relocator kit. Once the sensor is relocated, how do I get the sensor wire connector attached to the sensor ? Do I need to cut some of the plastic housing away ?
@davide1621 yes. Only cut the area i showed in the video. Do the wiring like i did in the crv ex video if you will be using the oem stalk
Please tell me how the side view looks like ? I have a 15% tint... at night I cannot see where I'm turning, habe to open window I really need a fog lights so I can see my sides where im turning into ! Does this fog lights provide good side coverage ?? Thank you.
@IvanRossS, it's good enough, but it the further it projects, the wider the beam spreads. They are very bright, so they should be fine for what you need them for. Just remember to aim them properly as they will need adjustment when installed.
Where do the sensors go? Cause yiu have to remoce them to place the lights
@WorldMythology-f9m this video shows where they go
How is the light output since installing a fog light is it a big difference compared to not having it on the crv
@neilgray6264 it is a huge difference. Watch the video time stamp 8:50 and you will see the difference when I turned it on.
Can the parking sensor be placed above in the body colored area instead? I see in some photos it can be. How would you do that? Do you need a body colored sensor?
@xulisvoosmuas yes. It can be placed in the bumper as you see in the pictures. Also, yes, you would need the body colored sensor, which is not available in the U.S. you would also need the hole punch tool to make the new hole.
Where can I purchase the body colored sensor and hole punch tool?
@xulisvoosmuas i know College Hills honda sells the kit, but I'm not sure if they will sell just the sensor. Punch tool from mikstore
Ok thanks. Also, will these sensors (from college hills) work with factory parts?
@@xulisvoosmuas I'm not sure. Reach our to their service department for more info
Hello. What diameter is the parking sensor tool? 18 mm? And did you move the original sensor to a new location? Or did you use a different sensor?
@promotionelista2780 I'm really not sure. I think it is tho. The sensors on the crv is 18.5mm. I had to make the hole a bit bigger to fit the oem sensors
If someone drove to you - would you do the install ?
@@iamerikr yes I do installs. Where are you located?
@@RTI876 straight down 65 in Nashville.
@@iamerikr I'm in Chicago
@ I’d literally drive to you to get this done right
Are you on any other platforms so I could DM you?
@iamerikr ok. That's fine. I do charge for installs. DM me on Instagram @ro_g90
Just got the kit. Do the light bulbs not flush along the plastic trim pieces? Any recommendation on the aiming of the fog light, like the setting of it?
@parthpatel6251 No, they don't. The adjustment is on the side. Adjust them all the way down, then check it, and if they are too low, bring them u up a tad bit. Just not too high where it's blinding to on coming traffic
@@RTI876 Ok thanks, Do you know how much you turned it? or are there any recommendations that I can find ?
@parthpatel6251 mine was already adjusted. Didn't have to mess with it
I could not get the radar sensors to fit into the retaining brackets included in MIkstore's sensor relocation kit. Did you have to modify them? The factory retainers are different and have slots in them for the ribs on the sensors.
@TerryBousha Yes, you have to trim the tabs that click in the sensor retainer
howd your installation go??
Does the dash have an indicator that you turned on the fog lights?
@tsukasadaniels1308 No, it doesn't
good question. Didnt think of that
Did you install the 35W fog lamps or the 40W projectors lamps? Also, after you moved the parking sensors, how well do they operate ?Are they same as before?
@@parthpatel6251 35w. They are bright enough for me. They operate the same as before
@@RTI876 with the 35 W is it projector lamp or reflector lamp? I am guessing the 35 W comes with a ballast to plug in so it can lower that much Watts, correct?
@@parthpatel6251 I'm not sure what it is. I know they are very bright. I'm also not sure if the ballast lowers the watts
@@RTI876 thanks
@@parthpatel6251 get the 35w. It's been working with no issues
Do your parking sensors work ok after moving them?
@@xulisvoosmuas they work just fine. No problem
Just had these installed. Seems like the left one is put in wrong and the light is facing up not down towards the grown like the right one. Do you think this is possible or is it defective? Left one is illuminating upwards like high beams instead of downwards!
@@FrandyMariaOvalles yes it's possible. They just need to be aimed properly. The adjuster is on the light itself
@@RTI876 does the bumper have to be off for adjusting the fog lights??
@lionintu it would be easier to do if removed. But i think they can be adjusted from the fender well
Sorry if this is obvious but how do I adjust the aim of these fog lights? Thank you
@gamblersstory9081 the adjustment is on the side of the light fixture facing down. You need an allen key to perform the adjustment. The area is at the bottom
Thank you. I got the 40w amber projector and I honestly think it just too bright and blinding. I think the glare is caused by the beam hitting the bottom housing and reflecting. I think it’s a design flaw. For the 35w you installed, is it very bright for oncoming cars? I’m thinking about switching up to the 35w. Thanks
@gamblersstory9081 i think the 35w is perfect, the 40w is think is overkill
@@gamblersstory9081 Is the 40w amber better than the 40w white?
Do the have that kit for 24 Honda HR -V good job looks much better
@joemontalvo50 sorry but the hrv does not have fog light option
@@RTI876 thanks buddy ok
Would this kit fit a 2023 Honda crv exl or, it’s specifically only for the hybrid? Thanks
too bad you over Chicago area, any people you know in Boston area you recommend to install that for me?
@@wingkeungngan85 I do not 🙂
Can you make a video on how to change the real turn signals for Hyundai Tucson n line 2023/24
@ahmediftekhar2503 I'm sorry, but I don't have that SUV at my disposal. My videos are done with my personal vehicles
Where can I purchase the body colored sensor?
? Doesnt your vehicle come with the sensor?
why did you wire it up like you did ? Why did you just not tap into existing lighting?
@jdagreek I was in a rush, and it was getting late, but I am going to rewire it to the fuse box
@@RTI876 how much for the honda crv 2024 front grille led
@jdagreek I'm not sure what that is
How were you guys able to wire the stalk switch connector to the foglights? After the part tapping into the 12v cigarette connector I got lost.
@joshuabob7302 Connect the negative wire to the stalk
I was wondering what are the 2 positive wires you have, I have the same kit as you guys did you guys use a jumper wire?
I connected the 2 positives together
Did you grab the 2 positives the green connector?
@joshuabob7302 I'm not sure where they came from. I'm thinking about rewiring it tho. I'm gonna connect it to the fuse box. I'll put out an updated video as soon as I get it done
How much did it cost including parts and labors?
@nahlho1807 I didn't buy the kit. It was sponsored, and I installed it myself. I think it will cost about $400 for everything tho... I'm not sure. I do have the lights for sale, not including the stalk. $150
How did you get those cables inside because the video didn’t show it .
@jackleung4519 I did, check time stamp 7:01
@@RTI876 oh let me check .
I saw the cable that you feeding into firewall. The harness come with black and red cables
I don’t know how to remove the shift gear cover
@jackleung4519 I'm not sure if their is any video on RUclips showing how to do it. But it's very easy. It's similar to the honda civic
Any chance you can find an hud installation kit 😢
@daaanielkim I don't know about that kit. What does it look like?
By chance do you have any suggestions on a better low-beam LED headlight bulb for the 2025 Honda CRV Hybrid Sport?
@mlawrence2991 you headlight is led. They don't use bulbs. Add a set of fog lights, they will make a difference
@@RTI876 ok thank you
The link to the foglight is in the video description
@@RTI876 When purchasing the fog lights from the link, do I get the "Fog Lamp Kit - Ultra White 35W" or the "Fog Projector Kit - Ultra White 40W"? I want to get the exact ones from your video. Thanks.
@mlawrence2991 35w ultra white. If you have the have a hybrid, be sure to get the sensor relocation brackets from the same menu
This is not for everyone. Must be professional to install
@@andyhuynh7933 I agree...
How the hell are we supposed to hear when you have that annoying music playing SO LOUD
@donwildermuth4347 if you were paying attention! you would realize their is no talking in the video! Just subtitles!!. Watch the other video for the detailed installation!!!
Wow that’s a lot of work to just gain 2 tiny lights at the bottom of the bumper. No thanks…
Have you seen the even tinier lights on the cx-5? These r fine. Question is, do they work
@lionintu they do work. I have another video with photos. You can check it out
@@RTI876 thank you and you wouldn't happen to be located near New York City would you?
@@lionintuunfortunately I'm not. I'm in Chicago
Would this kit fit a 2023 Honda crv exl or, it’s specifically only for the hybrid? Thanks
@RicardoGutierrez-b5z it works on all trim levels