@Dahen Zana Hello Dahen, I would like to ask the diameter of the copper for the rotary and inductor I measured mine, and gave me 0.47 for armature and 0.61 for the inductor(also same pws 125 a1 angle grinder). How much is important to stay on the same gauge? Your videos are very helpful to understand how proper winding is done. thank you
بارك الله فيك استاذنا الفاضل سؤال اتمنى الرد انت بدات اللف من اللامه التي فيها اخر ملف كيف يكون ذلك حيث ان الملف طبقتين والمفترض تكون البدايه من اللامه التي قبل اللامه الي انتهى فيها اخر ملف ياليت تشرح هذه الطريقه بالصوت والصوره بارك الله فيك ونفع بعلمك
I have a Parkside Angle Grinder PWS 125 A1, and I notice that there is vertical play of not more than 5mm in it's spindle, rotor moves either way ( up or down ) and overall it is working fine even the spindle lock, I just like to know that it is normal to have such vertical play, is it some kind of fault or company built it this way because it doesn't have any horizontal play, but my cousin's grinder doesn't have that vertical play that's why I am bit worried, can anyone help please
Hello, Thank you for vidéo. I have almost the same grinder Parkside PWS 125 F5. Mine is almost new. I have a strange problem with it. When it is cold, it works normally. But after a time of use when it gets hot, it refuses to work if speed selector is not at 6. And sometimes, it refuses to work completly. If i wait a little time like 2 minutes, then it works again at speed 6 and if i wait a little longer, it works at speed 1. I already changed the brushes and the interruptor, but it did not solve the problem. If you have an idea of what the problem could be, please, let me know. Thanks. 👍
@@brk932 Thanks for your feedback. I tested the armature (rotor) with multimeter, and it looked OK to me. The resistance value was constant between each track of the commutator and the resistance of each coil of the rotor was constant also, so i can say there is no short-circuit in the armature. also the rotor does not look damage or burned and the commutator was ok. With the vernish on rotor and stator i cannot say for sure if it is made of copper or aluminium, but the machine seems much lighter than my other grinder (makita) which have less power, so there is a high probabilty they are made of aluminium. Sometimes, brushes makes sparks but not always i think. And when it runs, it smells a brushes smell. Also, the wires that go to the stator from the electronic board look very thin to me considering the power (1200W) of the machine. The wire of the armature looks thin, but i cannot say if it is abnormally thin. I will try to change the electric feeding of the machine and some wires. But if it does not work, i will give up. Remake the rotor winding would be too complicated for me. Regards.
@@brk932 It stop very quickly (like 5 seconds) when it used to grind or cut. When it works without load, it can work longer (2 minutes or more) To me it look like the machine stop itself when high current are absorbed. (When it starts, and under load)
Terbaik, penyelamat para pecinta mekanik di tunggu video selajut nya😁🥰
Terima kasih Pak
Saludos Dahen, gracias mil por la clara Enseñanza.
Usta teşekkür ederim.Mükemmel ötesi helal olsun sana video çekim mükemmel eline emeğine sağlık
Awesome job you did rewindig angle grinder's armature, nice work,
thank you sir
You are a phenomenon! Congratulations
Thank you sir
Толковая работа!! Приятно посмотреть на работу Мастера!!
Спасибо, сэр
Hallo, ich verstehe nicht so ganz, wickelst du zwei separate Kupferdrähte ein? Oder wickelst du mit einen Draht das ganze Anker ein?
Impressive and inspiring. Many angle grinders get these or similar errors, and it can be fun to try to fix them.
A very good and clear film. Thanks.
thank you sir i hope it's helpful for you
ده ست خؤش زؤر سه ركه وتووبى
سوپاس برای بەرێزی
@Dahen Zana Hello Dahen, I would like to ask the diameter of the copper for the rotary and inductor I measured mine, and gave me 0.47 for armature and 0.61 for the inductor(also same pws 125 a1 angle grinder). How much is important to stay on the same gauge? Your videos are very helpful to understand how proper winding is done. thank you
Hello.the baring ,what size are they?
The motor of this angle grinder ac or dc ??
Amazing job!!!
thank you
Hi, what kind of Vaseline to use for an angle grinder, how do you use it in the video?
دائما مبدع أستاذنا العزيز ...
عاشت يدك...
اشكرك اخى العزيز
Verey good job
Iliked brother
Please rewinding armatur drill
thank you sir, i try
What a great work. Very good video.
thank you sir
Nice work and excellent winding. My brother.
thank you my teacher
you the best
Your welcome my dear brother. and You are the best too .
Thank you bro
Excellent travail
Merci Monsieur
Excellent work 👍
thank you sir
You are always the best. Swara
Thank you sir
ممتاز أحسنت العمل أستاذي العزيز 👍
اشكرك اخى العزيز
بارك الله فيك استاذنا الفاضل
سؤال اتمنى الرد
انت بدات اللف من اللامه التي فيها اخر ملف
كيف يكون ذلك حيث ان الملف طبقتين والمفترض تكون البدايه من اللامه التي قبل اللامه
الي انتهى فيها اخر ملف
ياليت تشرح هذه الطريقه بالصوت والصوره
بارك الله فيك ونفع بعلمك
Plz Wire size gauge ?
Is it 25 swg or awg ?
Thanx
great channel . where are you from??
thank you sir, kurdistan
How to find a place to start
Great job.
Thanks alot
Greetings from Romania 😊😊😇😇
thank for all Romanians people
@@zana3587 r445
مرحبا استاذ... هل كل انواع آلات القطع (باركسايد) 125ملم لها نفس طريقة اللف
بصراحة لا اعرف . اسف
The main file has how many rolls per electrode and how much is the wire size.. please answer ....... with thanks and appreciation to you
file!
I have a Parkside Angle Grinder PWS 125 A1, and I notice that there is vertical play of not more than 5mm in it's spindle, rotor moves either way ( up or down ) and overall it is working fine even the spindle lock, I just like to know that it is normal to have such vertical play, is it some kind of fault or company built it this way because it doesn't have any horizontal play, but my cousin's grinder doesn't have that vertical play that's why I am bit worried, can anyone help please
ok
Bro how to use the growler to check the armature can you please make a video on that
Yes in the future i have a plane to make video
@@zana3587 thanks Bro
what happens if you put a wire gauge a little thicker ???
I have not tried it before
Hello,
Thank you for vidéo.
I have almost the same grinder Parkside PWS 125 F5.
Mine is almost new.
I have a strange problem with it.
When it is cold, it works normally.
But after a time of use when it gets hot, it refuses to work if speed selector is not at 6.
And sometimes, it refuses to work completly.
If i wait a little time like 2 minutes, then it works again at speed 6 and if i wait a little longer, it works at speed 1.
I already changed the brushes and the interruptor, but it did not solve the problem.
If you have an idea of what the problem could be, please, let me know.
Thanks. 👍
i have one but it's broken i think the armature is the problem i try fix it in the future and make a video
Overheating! Probably armature wire is too thin or made of aluminium. Does the commutator look fine? Does it spark?
@@brk932 Thanks for your feedback.
I tested the armature (rotor) with multimeter, and it looked OK to me.
The resistance value was constant between each track of the commutator and the resistance of each coil of the rotor was constant also, so i can say there is no short-circuit in the armature.
also the rotor does not look damage or burned and the commutator was ok.
With the vernish on rotor and stator i cannot say for sure if it is made of copper or aluminium, but the machine seems much lighter than my other grinder (makita) which have less power, so there is a high probabilty they are made of aluminium.
Sometimes, brushes makes sparks but not always i think.
And when it runs, it smells a brushes smell.
Also, the wires that go to the stator from the electronic board look very thin to me considering the power (1200W) of the machine.
The wire of the armature looks thin, but i cannot say if it is abnormally thin.
I will try to change the electric feeding of the machine and some wires.
But if it does not work, i will give up.
Remake the rotor winding would be too complicated for me.
Regards.
@@samirazarzar6279 How much work does it take before overheating?
@@brk932
It stop very quickly (like 5 seconds) when it used to grind or cut.
When it works without load, it can work longer (2 minutes or more)
To me it look like the machine stop itself when high current are absorbed. (When it starts, and under load)
Thanks for your video
thank you sir
Is this AC or DC motor?
ac motor
Great video If the available wire measures 26, the question is how many turns of one duct?
thank you sir , 13
Bhai sath mei voice hoti to aur jyada helpful hoti...
Super , bravo ! Respect!
Thank you sir
عالی بود استاد دستانت رو باید بوسید
متشکرم، این برای شما بسیار مهربان است
كم قطر اسلاك الكويل وكم عدد لفات القطب ال واحد(للملف الرئيسي وليس الارميجر) لك كل الشكر والتقدير
الملف الرئيسى لو اقوم بلفه . فقط الارميجر
@@zana3587 اشكرك كثيرا على الرد
أحلى لايك لأحلى معلم .
اشكرك اخى العزيز
Great !
Have you a wiring diagram of the connections you can provide me? Thanks
no sir, but in the future i make video in explain everything, i have another one
Muito bem valeu amigo
Кама 5 pump якоря схемы можно
To be honest, I didin't understand a bit which winding goes where.....not really explained well
فعلا master 👍👍👍👍👍👍
اشكرك اخى العزيز
Super Arbeit
Danke mein Herr
👍
Thank you sir
Молодец
Спасибо, сэр
Good 👍🌹👍🌹
Thank you sir
ممتاز.. شكرا لك
اشكرك اخى العزيز
Смазки в редуктор много
Keşke yaptıklarını anlatsaydın.
Thats too much grease broo
thank you sir
😮❤
bingla bust sister
0