🛩️Heewing T2 - Detailed Step By Step INAV Build Tutorial
HTML-код
- Опубликовано: 28 ноя 2023
- A detailed step by step build tutorial for the Heewing T2 Cruza RC plane. This tutorial shows how to assemble the aircraft, install a flight controller and other electronics, and also how to do all the required INAV programming to get the aircraft in the air :)
Wanna throw me a few dolla to help me keep making videos? www.buymeacoffee.com/gizfpv
The CLI codes for those that need them:
set max_angle_inclination_rll = 600
set max_angle_inclination_pit = 600
set small_angle = 180
set nav_fw_bank_angle = 35
set nav_rth_altitude = 7000
set failsafe_throttle_low_delay = 0
set nav_rth_allow_landing = FS_ONLY
set disarm_kill_switch=OFF
set nav_extra_arming_safety = ON
3d print files: Coming soon... 
Наука
![Megan Thee Stallion - Rattle [Official Audio]](http://i.ytimg.com/vi/qY6qwqVCsww/mqdefault.jpg)
It’s amazing how much work you put in theses build videos, thank you so much!
Thank you for the instructions. Looking forward to building it with my son (our first build).
Thanks a bunch for the how to, dude! 😃
Fantastic flying!!!
Stay safe there with your family! 🖖😊
And happy holidays!
Благодарю! Вы проделали большую инженерную работу.
Hell yeah bud super awesome and informative build video, cannot wait to receive and build mine out wit the Matek f405 WMN board.
Good job!
Great work ! I just wish the T2 was cheaper
Absolutely superb description of how to build the plane and program the FC. The video must have taken hours to complete, well worth the effort. 👍👍
Only about 2 months 😂
Ouch! That’s dedication. Thanks for taking the time, it’s appreciated.
Very detailed video. To me, crimping all those servo leads will be a deal breaker.
Your detailed pictorial overview is the best on U Tube IMO....I need a Dupont crimp tool, convinced now....I have the plastic recepticles, and bucher servo leads. Its not ideal though....Well done matey, great effort....🤔😳👍👍😏😀🇬🇧
A Dupont crimp tool is a must if you wanna do tidy wiring. Will be a worthwhile investment :)
Great tutorial, thanks for that. Not sure if I will keep the original PCB, and stick the FC on top.
Also the Reveiver might stay inside the fuselage, less connectors, less worries.
I'd like to have Pan for the Cam, to watch the Prop spinning. Weekend ahead, construction time!
That's a lot of work for this video. Now, do this all over again for Arduplane setup ;).
I will when the VTOL kit comes out lol
Super impressive! I want to get into this hobby, but might start a little smaller.
Heewing T1 would be a good place to start :)
@@gizfpv ok thank you! I just watched a video on one of those. It did look like a good place to start.
Great video, just got mine with similar fc, was wondering if you had the 3d print files available by chance?
Maybe you can share your OSD cli, its nice. Thanks
It seems like, my LEDs have no ground... No light with the 9V output on speedybee wing f405
Hi Giz, I have followed your build with only two exceptions: I used a BN-220 GPS (no compass) and a RadioMaster RP-3 receiver. The last problem to solve before maiden is getting all the telemetry sensors working. I'm seeing only 9 and have deleted all and re-discovered several times with no luck. Telemetry output is turned on in Configuration and Serial Receiver Provider is set to CRSF. I've double-checked the receiver wiring. The receiver is working otherwise. TX16 radio running latest EdgeTX. Any ideas? Thanks!
Never mind! Discovered my crimped connectors were not properly seated in the Rx Dupont connector. Fully telemetry now.
could you please provide the printed file for the fc? Thanks a lot
You don't build the plane, was Bob!! xDD
Will you VTOL it? ❤
When/if a VTOL kit becomes available then yes 😊
@@gizfpv cool! are there enough contacts in the wing connector to upgrade without removing flaps? Thanks!
be careful guys. the whole wiring order changed... looks like i received a V2 or Mark2 or whatever...
Why can’t u leave it in
Leave what in?
@@gizfpv bec that come with t2
@@Dashone93 The PDB you mean? You can leave it in if you want, but it's not needed when using a proper flight controller as it has its own PDB built int
If I leave it in with SpeedyBee 405 wing it only shows one motor so I got to take it out