My friend, when I drive on the highway, I get error number 84 and the car enters the safe situation. Do you have a piece of advice that I have to work with or a video that I have to watch? Thank you.
Hi, i just checked my 2010 meriva 1.7cdti map sensor values with Wurth Wow and delphi softwares . Off engine -100kpa , at idle 99kpa. Map sensor dead? Have a higher diesel consumption .
Brother pls help my fuel pumb is not priming .And the relay clicks & fuel pump works only when the the key is fully turned to start position ......what is the reason for this delay in clicking of relay ......is my map sensor clogged.....help me out pls.....opel corsa classic 2005 ...
Hello, My problem was (now is always) the engine speed needle it's not stable. After clean the map sensor it was better and stable for the engine. Few killometers the problem was come back. Do yo know if i need change the map sensor ? Or it's my injectors are bad ? Thank you for your job.
... may be you need to reset the ECU with unplugged battery connectors. Take them off the battery and wait some minutes. After that, connect them back and drive some hundreds of km-s to set itself.
poštovani Zlita , odličan video! imam jedno pitanje; Imam istu Astru kao i ti , pojavio mi se problem sa dosta nemirnim radom u leru (172.000km) a ustanovilo se da prva dizna (denso) ne radi dobro. Istu sam reparirao ostale su provjerio te postavio nove kodove na sve 4 dizne. Auto sada radi sasvim normalno ali mu je ostala uključena lampica (auto sa ključem) koju je nemoguće poništiti sa Bosch dijagnostikom. da li moram ići u ovlašteni Opel servis ili imaš neko drugo rješene ? hvala na odgovoru lp
zlita hvala na odgovoru . Na Delphi dijagnostici Pise da se radi o greski P062B sa ljedecim napomenama: smanjenja kolicima ubrizgavanja ,nije ucitano ,trajno? Nisam jos riješio problem Da li si se susreo sa takvom greskom ?
Hi,although i didnt remove the MAP as i didnt have right screw driver at the time ,i removed the sensor adaptor and put back properly.Next day on starting engine light came on .i cleared the code with torque pro.I plan to clean the MAP sensor,shall i disconnect the negative terminal of battery before removing MAP next time.code was P0108 high input ,your advice is appreciated.thanks
You have to spray... cos that is the only way to clean it... dont touch sensor with finger or somthing else. My was clean cos i already cleaned it... just did it again for video...
@@webrtywebrtyhebrtyhebrty899 I definitely have a bit of shuddering/hesitating when accelerating from idle, I have to give it more gas to take off only gently. It is a 2007 astra H 1.7. I should check EGR valve too I guess
My friend, when I drive on the highway, I get error number 84 and the car enters the safe situation. Do you have a piece of advice that I have to work with or a video that I have to watch? Thank you.
i dip them in nail varnish remover(acetone), your videos are much appreciated, i have the same car with 300k km, thanks
what product do you use to clean the sensor?
My sensor won't come out what might be the problem.
Could I lever it with a screwdriver or would that be dangerous
My friend, when I drive on the highway, I get error number 84 and the car enters the safe situation. Do you have a piece of advice that I have to work with or a video that I have to watch? Thank you.
Nice, thank you
Hi, i just checked my 2010 meriva 1.7cdti map sensor values with Wurth Wow and delphi softwares . Off engine -100kpa , at idle 99kpa. Map sensor dead? Have a higher diesel consumption .
if its really faulty you also will have a bad acceleration symptoms.
Koji ti je ovo sprej za ciscenje.
Jel VD sprej ili neki drugi. Hvala
Thanks for the easy to follow video. I cleaned my MAP sensor with your assistance!
Brother pls help my fuel pumb is not priming .And the relay clicks & fuel pump works only when the the key is fully turned to start position ......what is the reason for this delay in clicking of relay ......is my map sensor clogged.....help me out pls.....opel corsa classic 2005 ...
Now i wait for an EGR valve cleaning video. 😊
@Adrian Kozlowski
You are an idiot.He just said not to use WD40.
@@bestguest11 Yes he said NOT to use WD40 twice, its oil based thats why.
Hello,
My problem was (now is always) the engine speed needle it's not stable.
After clean the map sensor it was better and stable for the engine. Few killometers the problem was come back.
Do yo know if i need change the map sensor ? Or it's my injectors are bad ?
Thank you for your job.
When i had unstable engine idle it was SCV. Suction control valve... Check with your mehanic.p
... may be you need to reset the ECU with unplugged battery connectors. Take them off the battery and wait some minutes. After that, connect them back and drive some hundreds of km-s to set itself.
What cleaning product are you using??
Hi, what tool are you using to unscrew the bolts?
Ratchet and socket
My one was completely black. you couldn't even see the gaps. Thanks alot.
matori čarape su ti vrh :D
Ivan Filipović a zicer je balkanac :D
Svaka čast na komentaru!
Hello I can not recognize the brand of spray can u tell me what kind of spray you use for cleaning the map sensor
Any spray for cleaning electric contact... brand is not so much important... wurth or similar is ok... dont use wd40 cos it leavs layer after dry...
0:16 I actually lost my turtle...
I have lost a turtle as well it has 4 legs :(
What spray did you use..
contact or brake cleaner
@@arameka10 do not use brake cleaner! use maf sensor cleaner only overwise it will destroy your sensor 👍
Great video very descriptive
poštovani Zlita , odličan video!
imam jedno pitanje; Imam istu Astru kao i ti , pojavio mi se problem sa dosta nemirnim radom u leru (172.000km) a ustanovilo se da prva dizna (denso) ne radi dobro.
Istu sam reparirao ostale su provjerio te postavio nove kodove na sve 4 dizne.
Auto sada radi sasvim normalno ali mu je ostala uključena lampica (auto sa ključem) koju je nemoguće poništiti sa Bosch dijagnostikom.
da li moram ići u ovlašteni Opel servis ili imaš neko drugo rješene ?
hvala na odgovoru
lp
Servis koji ima opcom ce ponistiti. Verivatno moze ibsa tech 2 dijagnostikom. Nemoj ici u ovlasteni, odrace te nizasta 😀
zlita hvala na odgovoru . Na Delphi dijagnostici Pise da se radi o greski P062B sa ljedecim napomenama: smanjenja kolicima ubrizgavanja ,nije ucitano ,trajno? Nisam jos riješio problem
Da li si se susreo sa takvom greskom ?
I cleaned it with brake cleaner. And now it feels clogged on 2nd gear
how many kilometers will be cleaned?
George Vergos i clean my every 50k
With what spray did you clean the sensor?
spray for electric contacts
Thanks! Very usefull videos!
Can you please tell me the brand name of the electric contact spray? Thanks
brand is Motip... electric contact cleaner
Thank you 😊😊😊😊
Cheers
Thanks for video.
Thank you
Buraz pricas ko pravi englez 😂😂
Thank you arkadas 👍
My map Sensor was very very dirty!??!!
Thank you!
afterwards, the grass will not grow !! ;))
Hi,although i didnt remove the MAP as i didnt have right screw driver at the time ,i removed the sensor adaptor and put back properly.Next day on starting engine light came on .i cleared the code with torque pro.I plan to clean the MAP sensor,shall i disconnect the negative terminal of battery before removing MAP next time.code was P0108 high input ,your advice is appreciated.thanks
I did not removed it, just disconeted directly from sensor.
You don't need to spray that much?
You have to spray... cos that is the only way to clean it... dont touch sensor with finger or somthing else. My was clean cos i already cleaned it... just did it again for video...
just buy a new one and you are good for the next 130.000 miles :)
Thank you Bolshoi Spasibo.
Dobry jesteś.
Bedankt!!
Well done
I clean it. It was verry dirty at 184000 kilometres
i cleaned it after 185000 km too...
Good job
Ripple coin
dont lose no turtles
Not on the grass man!!! this goes in the ground and after in the water that your kids will drink!
WHAT PROBLEMS MAKES THAT SENSOR TO THE CAR ?
idle drop, loss of power, hesitating when accelerate, longer start
@@webrtywebrtyhebrtyhebrty899 I definitely have a bit of shuddering/hesitating when accelerating from idle, I have to give it more gas to take off only gently. It is a 2007 astra H 1.7. I should check EGR valve too I guess
👍
How long he took the connectors off 😂😂😂😂
такого бедного немца не видел ))) в порванных ботасах ходит.
But it's not well done to throw the spray liquid to the ground!!! It's so polluting!!!
My friend, when I drive on the highway, I get error number 84 and the car enters the safe situation. Do you have a piece of advice that I have to work with or a video that I have to watch? Thank you.