Volvo Transmission Position Sensor (PNP Switch) DIY - S60 V70 XC70 S80 XC90
HTML-код
- Опубликовано: 9 окт 2024
- Adam gives a quick DIY on how to replace the Automatic Transmission Position Switch, aka Neutral Safety Switch, aka PNP Switch located on the transmission for any 01-07 S60/V70/XC70 automatic, XC90 2.5T, S80 5cyl 04-06. Trans fault code 0039 is a common indicator of a faulty PNP switch.
eEuroparts carries a huge selection of Genuine, OES, and Aftermarket parts for your Volvo, check us out at eeuroparts.com
Product Link: eeuroparts.com...
I just did it on My Volvo s80 D5. Followed hes instructions it worked. It's this kind of People we Love having on RUclips. Cheers mate
Very informative video. Just a special note: before undoing a bunch of things inspect your cable harness for connectors not completely seated. This causes various codes depending on which sensors are affected.
Have to say thanks. Most troubleshooting said the dash indicator would be blank. You said "or a dash." That's what I had. Just installed the new switch and my 01 S60 is running as well as she can. Quarter of a million miles and going strong. Thanks for the info!
It's always easier to remove the shift cable first! Very easy!
I like this guy. He seems pretty down to earth
good video
the 4 - 5 comments under top selection says it all .. plus
1.
Clean underneath the sensor, careful around the shaft of the selector axle before mounting the new.
2.
Get some silicone grease for the rubber seal in the el. connector, best is food grade silicone grease as it is acid free (Bardahl makes some god stuff, also anti-seize grease)
3.
Loosen all other things first before removing the bolts holding the sensor .. check those two bolts first of all, if you can't loosen them, no need to go on before they are loose
This goes 'specially for filler plugs too in all them "oil containing reservoirs" like gearbox, bevel gear, Haldex, Differentials, etc.
And don't yank that gear stick like a "nun holding a d**ck" .. nice and easy, calm and smooth. A Volvo is like a fine woman .. they need to be tickled and teased in the right places too to get up 'n running .. OK
From the 4 year Scandinavian trained, VISTA certified Volvo mechanic ...
A couple of tips. Remove the MAF. Use a hair dryer or heat gun to slightly soften the plastic tight fitting hose. Then remove the air box top with the Maf still attached to it. Route the new cable before putting the sensor back on. Take notice that the new sensor bolt holes are not round. They are elongated bolt holes that will allow adjustment of the sensor if the car won't start and or the indicator lights don't come on.Make sure to disconnect the battery.
I tried watching a different video before finding yours and it was brutal! Thanks for making this video, great job!
Did your transmission act up a little bit like it didn't want to pull cuz mine's doing the same thing in the video but it acts like it don't want to pull
God Bless you man, I was struggling to remove this sensor thinking I should remove the bolt like thread on top, u really helped me with the "wiggling" part
Hey guy i just wanna say this is a great video, but lock in carefully also change the vehicle speed sensor while you are here. Trust me.
Do you by chance know where this at I can not find it. And there is no videos at all where it is.
A good, practical no nonsense video, Adam. Thanks. I did this job on my old 850 and found that the positioning of the switch was critical to within a couple of millimetres, otherwise it wouldn't work. I made an alignment tool to get it just right.
You seem to fit the switch without any adjustment, and it worked. Presumably things have moved on since 1994! I have just acquired a 2004 V70 so would be interested in your thoughts on this issue.
Best wishes from the UK.
The switch definitely does look to have adjustability built in, when originally filming the video there was an extra step to not tighten the bolts until calibrated but in this case it just worked. Luck? Hard to say. Anything with ovoid mounting points should always be assumed to allow adjustability and calibration.
Thanks for the reply. I wish I had your luck!! I found this to be a pig of a job to get the positioning just right. I made an alignment tool from a pair of tweezers and a bit of wire. The tweezers were fitted over the central spigot secured by the wire wrapped around the prongs of the tweezers. The top of the tweezers can then be aligned with a mark on the switch like the hand of a clock. It worked well.
The other way is to put the shift in reverse and move the switch until the reversing light comes on. Keep moving it until the light goes off. Half way between the two points should be the correct alignment.
I hope this is of use to someone.
Great video. After doing this repair, squirrels ate through the wiring. Tried peppermint oil, but it doesn't work. Won't even last a day. One red wire that was cut, had internal wiring, six total. May have to replace the conduit and find a new parking spot or sell it as is. Every wire in my Volvo is now a target.
You need a good pellet gun with a scope.
I hate squirrels! They aren’t cute. They’re basically tree rats. You realize this when you have an encounter with them like you did… in my case they got in my attic and chewed and scratched for weeks till I could get them
Put some peanut butter on the wiring.....the squirrels will love it 😁😁
Any info on why one would drive for like 20 minutes and then just stops shifting and moving all of the sudden . Let it sit for few drive again and then another 14 minutes or so it won't pull again
Filter is clogged. Have to drill a hole in the case and poke holes in the filter. Tap hole and insert bolt.
I'm glad you know what to do!
Great video, I just change the transmission fluid on my volvo s60 2001 is a little overfilled according with the mark, but now when I start my car and shift over drive wont engage any shift, wont work on d or r just dont move, could be a faulty pnp switch
Too much fluid. Drain it out and your filter is clogged. How did it turn out?
Hello from India I love the way you explained everything about speed sensor....I'm in process of getting a 2007----S80 v8 model which has transmission problem can I get custom 5speed manual or a sequential transmission for this particular car.....I have zero idea if anything like this can be done.
There is might be no room for different transmission. Of course you can fit there any transmission but amount of labor, modification and skills needed may prevent that kind of swap.
I LOVE YOU MAN!!!
I WAS WHY TOO WORRY TODAY IN THE MORNING WHEN I GOT THIS CODE IN MY XC 70!!!
just one more question, what are the symptoms or defects that the transmission presents with this damaged sensor, thank you
It can be a number of things, from a simple light on the dash, inability to start, and inability to shift.
eEuroparts.com hola hermano no hablo inglés, tengo un Volvo s40 1.9 T y me apareció en el tablero pin code y ya lo lleve a los mecánicos pero no sabes help me plis bro
The best video thanks for uploading💞
Have a 2005 xc90 turbo 5cyl
the conector on my selector conects to the selector It has no cable conector. Went to the junk yard and found the same model as mine but the selector Is the same as in your video. My sensor shifter has a removal conector not like the one in the video.
Good Morning, I know own my sisters 2002 S60 and when i drive it does slip when I step on the gas hard. or make a left it slips. So I am now researching what the issue is. I till make a note of this also I do have a card reader, so I will do this today sometime. Thanks for the videos. I hope this is the issue. I don't want to worry it might be something bigger in the transmission. Well that is what we do. Trial and error. Hope this is the fix. but I have much to check before saying this might be it. Once again thanks for the videos.
Was the position sensor the problem. I have the same problem on my volvo c70
Hey David did you find the solution?? My 2001 S80 T6 does the same thing, slipping if I accelerate hard or instantly slips if turn left, turning right does hold quite more "abuse" on the gas until it finally slips.
Clogged filter.
Will the transmission still function properly if this sensor is faulty? I'm having a difficult time finding this part for an S60 2004.
No, the transmission will not know what gear it's in and will most likely go into limp mode. In some cases the engine may not start if it can't tell if it's in gear or not.
Very helpful. Thanks!
My fault code reads 0705 not 0039 as you mention. Same problem?
Vikingdescendent you Can find one on ebay for 55$ and you'll ruin you're transmission in the long run if you don't change it.
@@Eeuroparts same thing with my volvo, it seemed like it was starting from 2nd gear and not going beyond 4th gear, I found a 2nd hand sensor and will install it later today, I hope the message "Transmission service required" and engine sign will go away because both occured concurrently when I was accelerating hard
Hi. Thanks for the video firstly. Always clear and making it seem easy peasy. Of late, my display only shows P, R, N and D. When driving, it simply doesn't display any gear except that it shows D. Would this be an issue with this module too?
what car, model, year, engine, gearbox, etc.??
fx. like this: Nov 2014 XC90 D5 AWD Executive, Chassis PNCVZ3056E5xxxxxx, engine D5244T18, gearbox TF-80SC (happens to be mine)
But in normal AT driving mode, you only get a 'D' in the display.
Only in Manual shift mode aka 'Tiptronic', you get the gear shown in the display.
@@tellyonthewall8751 ah ok, then it might just be my error to assume that it would show in auto shift mode as well because I was switching between tip tonic and auto to test the shifts.
Mine is the 2006 volvo xc90 d5 awd. D5244T4
How do you know this Is what yoi need? And not the TCM?
I have a 2003 Volvo xc90. Drove to store came out and the car would no longer move in Drive. I can slam it down into manual and shift to 3rd gear and it drives. But I have to slam it back into manual for it to go into manual. If I just move it back and over to the manual position it stays in Drive. But when I slam it back it goes into manual but only will move in 3rd gear. Never had a problem before. Never slipped or shifted hard. Sometimes when I put it in drive I would have to wiggle the gear shifter around to get drive to engage. Since it never had any issues before as far as slipping or shifting hard, I am lost. Drive just stopped working suddenly. If you have any ideas or suggestions please help. It would be greatly appreciated.
What ended up being the issue for you? I'm having the same issue... No drive just 3rd in manual mode
I have a starting problem with my 2003 Volvo S60 every once in a while.
I suspect(ed) the PNP switch, but you say then the display would not show in what position the gear selector is, but that works fine on my Volvo.
I suspect it because when I have that problem and move the gear selector all the way (with serious speed) up and down it will crank eventueally.
But now I start wondering if it will be the PNP switch.
I do not have any transmission fault codes. Not on the info display and not on the OBD scanner.
And VIDA or D5T5 is saying?
Thanks for the detailed video. I replaced this switch in my 01 XC70. It worked great for a little while, them i got the same code error, and transmission won't shift again. I checked the alignment on the switch and it seems to be fine. Any idea on what else could be causing the transmission to stop shifting? The code I have is P0740.
Hello, were you ever able to resolve this? I have an 01 XC70 and am getting a P0740 code also. Thanks.
hello adam, this pnp sensor that serves, you did not in the end tighten the two screws of the sensor, I would like to know if they should still be with a slight tightening, thanks for your video.
Yes, everything should be tightened snug, not too tight because the aluminum is soft.
just saw this video great thanks.do you have tip to diasppear the airbag error code as well?I ve not been removed the battery befor I repaired the radio so it is visible since then. or it can be done only via OBD?S60 2.4.2001 thanks
How long can I drive with a bad gear shift position sensor before it starts affecting transmission?
Depends how much you want to pay out on a dominoes effect when Transmission mis-selects or short circuit other sensitive circuits.
Note that the new injectors are adapted to the vehicle processorhello, please help. Volvo 2.0 diesel had an engine failure during which the engine was damaged. During the diagnostics of the vehicle, she reported an error that the engine was forcibly turned off because it has engine protection that is activated due to uncontrolled oil circulation through the engine. The new engine is installed, but it won't start. What actions are needed to start it again, that is, to remove that protection. Thanks if you help
Hi there. I have the same code on my 2005 XC90 but everything is working fine. I think I just need to remove the error code. What do I need to do to fix mine please? Thanx in advance
Yes I love this video because I have a Volvo S80 an I fix mine the same switch I fit my self
Just did this on my 2004 s60 2.5t awd, is not working right, any tips?
I wish he show the icon that displayed
" - " I have been searching for a while and looking at xc V70 for years know and have never seen the information I also maybe you know I have a solenoid fault
"E" but electrical p0773
Got a volvo c70 x reg 2.4 petrol automatic losing power in 3rd and 4th gear then drives fine then loses power car doesn't move whilst winter button is pressed gearbox oil changed still no change in gears and losing power any advice help appreciated sean from Scotland
Im having a simular problem, wondering if you ever figured it out, over there in the Land Of Scota. Was it this sensor?
Hello friend, I'm from Brazil, how are you? mine and the s80 2.9 it's turning on the direct injection light, I've already changed the transmission fluid, the spark plugs and the coils, but sometimes it's just 3 gear, do you think that can be it?
I know I’m super late but mine recently has been acting up and I’m replacing it, will it cause your car to shift rough? Mine has been lately but I’m not sure if I should just change my transmission fluid
Did u figure out what was wrong with it ?and did u fix it?
Yo tengo un volvo automatico la unica marcha que tiene poca fuersa es la reversa,, ojala me pudieras dar algun consejo atentamente Carlos.
Why did you change the pnp?
its hard to find switch automatic sensor for my volvo s40 in Indonesia 😟
can it be fix by service it?
or it must be change the new one?
help me if all of you guys have information, thx..😊
Do you have smoothly gear now?
My manuel gear is very hard and i don't know if it is the gear or cabel.
Hey thanks for the video. I know it's 6 years after the fact I've got a Volvo V70 2004 that is doing the exact same thing. But I'm getting a trouble code that says my shift solenoid S1 signal is missing. Could just be caused by the pnp?
Hello, the arrow sign is on and it only goes in 1st gear, it does not shift to 2nd gear. Was this your problem? I would be happy if you let me know how it was solved.
My car Volvo 850 1997
Hi Adam, 99 volvo xc70 transmission stuck in neutral. Will replacing this sensor fix the issue ?? Thank you.
Well done!! Good job
Very good, thanks!
2012 Volvo S60 t6 r design throwing Po730-00, seems to drive almost normal, not sure if I’m second guessing it now that there is an engine code, I’m at 2500 RPM with cruise set on 75mph, all gears still function properly as far as I can tell, any help? Would be greatly appreciated
I noticed that you didn't reload the transmission programme. The Volvo dealership stated that you can install the module but, needs to be reprogrammed and car driven to relearn the new module shift sequence...or is this a repair ploy to charge $300 for nstallation and $80 dollars to say that is what it needs?????
Volvo likes to reprogram the transmission after any kind of service to allow it to calibrate perfectly. However, Adam did not reprogram this and the car drove fine without fault.
Volvo dealers always claim that parts need to be reprogrammed.
I put my car in drive, release brake to mive car ahead and in seconds the transmission goes from. normal to glitch mode with little forward traction and when it does that it either disengages the RPM gauge and the gear Shift indicator, you dont know what gear you're in. Also, the D or R light n the gear shift panel can get stuck in D even if you move the shifter to another position. Transmission Requires appears, some times the engine service appear and the battery disconnected seems to be the only way to get rid of the service notifications. In Glitch mode I get cluncking. In Manual Mode with lever pulled all the way back. the whizzing sound heard in D and Reverse disappears - also heate in manual mode when lever is not pulled back and yes, slipping there. When engaging in the manual mode lever pulled all the way back there is a big clunk
The transmission shop pinter to fommunication problems as well as a Higher Than Permitted 'something' in the ABS system, he didnt know how to explain the high reading and said it could be too high a voltage with a cause, could be open circuit. The car drove well when I bought it 3 weeks ago for two days and thw it started to slip. I started shutting itniff in Drive mode making it possible to maintain normal transmission pull IF it had been workng Normal on the trip but at one point that didnt work anymore. Previously I had to wait for the engine, transmission temperature to go down big time. Yransmission shop said the gears dont slip and the thing must be entering Limp mode.
SOS, is it the PNP Switch?
thank you som much!
are there any videos or any info on replacing rpm sensor on a 2001 Volvo s60 with 2.4 t engine
The operation should be similar
Does it need to be align? Or adjusted? Or it's kinda like plug and play?
no start on 06 xc90
It can be finely adjusted, but we found it to be plug and play.
I switched mine out but now it won't shift, do you have any suggestions? Please help.
Could this also cause issues with the geartronic not wanting to function. Shifts in auto normal but wont go in manual mode. Also the selector lights are dead
@Gayle Davis my issue ended up being corrosion on the tcm pins, cleaned them up and used contact enhancer and presto, shifter works flawless
Great video!Do you need to disconnect the battery for this job?? Thanks!
Did your transmission act up a little bit like I didn't want to pull when that sensor went out
Hello dear sir,
I have problem with reverse in volvo s 80 so the gear is working propebly in D position but when i but in reverse the car cant go back. So please feed me back with the solution , my secerly,,,
In order to reinstall the cable to the PNP switch, I had to place the shifter in drive 3. It would not line up in P.
Thanks for the input.
Do you know if it could possibly skip a gear?
Thanks for this video ,!!!
Did the transmission act up like it didn't know what gear it was in
Can't find why changing my Volvo's transmission with a PNP Switch wouldn't help me here? It may be as simple as changing this PNP sensor cable. My transmission will not shift (ie) Tip-tonic gear selections -MAN+ is this sensor the culprit ? (By replacing this sensor my transmission -MAN+ may work ? Thanks
You should have a VIDA enabled diagnostic system plugged into your Volvo to diagnose this.
Mr How are l’m from libya my name is Gamal I want this parts for my car Volvo model 99 S80 how to get it and Iwant ask about it’s price if you able to help l will be pleaser to you
my engine light is reading replace speed sensor but my car is also , is not telling me what gear I'm in so do I need to replace both speed sensor in position sensor 2002volvo s60
Filter is clogged.
Need help....If anybody knows what that black tube is @5:28 , it is just above his hand and my car doesn't have one , you can see a clamp that's left on a bit of hose .would love to buy a replacement part for it but cant find out the name.
I'm having the same problem with my 2006 Volvo XC90, would the process be the same? Help please
How do I turn off
Winter mode mold in myMy 1999 Volvo
my volvo xc 90 2.4l diesel 2003 has a problem of auto box. In fact when you start, it moves forward or backward,
then after 2 minutes more nothing, normal as nothing
you can imagine in city area parking place are to congested...
now what could be possible???
Filter is clogged.
are these cars a good car to buy? are they expensive to work on?
Iseekoutthetruth. Free to work on but you'll need your tools lol. Parts are a bit more expensive than average especially sensors. Qualified competent labor is somewhat expensive.
Hell NO!!!!!!!..... Everything is falling apart..... Chinese junk.... badly deigned badly engineered. Good luck to replace PCV valve as an example.... and if you don't.... kiss your engine goodbye.... one word JUNK.... good looking though..... get something reliable....
@@stnln2180 I've done a full PCV replacement on two P2 Volvos, it's nothing out of the ordinary lol...
@@reallyhappenings5597
Everything is relative. Here's Volvo pcv replacement ruclips.net/video/oEOzIoVxO4s/видео.html
and here's Toyota ruclips.net/video/QmoChd_18mQ/видео.html
Do I need to say more?..... 10 min. job vs 2 hr.+
@@stnln2180 I agree I owned 5 Volvos ...all need upkeep every 2 months...if you cant fix cars stay far away or your pocket will be empty...the garage guys call these NEEDY CARS …..
my car is not functioning very well, it keep on showing me transmission services required and most time it will stop on the road until it get cool before it will move again, what can be the problem please ?
Victor Titus you may want to take a look at the cem, mine was overheating causing it to die randomly and refused to restart. Open the cem up, and there will be a metal plate/ shield, remove it and place a small heat sink on the chip. (25mm X 25mm is the right size I think)
mike judge what is "cem"? i have the same problem tha was comented.
@@tiagobosze9604 central electronic module. It is near the brake pedal under a plastic panel. Kinda a pain to get out. There are a few videos on youtube on where it is and how to remove it
mike judge Ok, thank you so much. This heat sink is easy to put?
@@tiagobosze9604 its easy to put the heat sink in, just a pain getting the cem in and out
Great vid. Thx!
my volvo xc70 2004 automatic is taking a few strides/leaps when changing gears. Can this sensor in the video be the cause of the problem?
www.eeuroparts.com/blog/4739/is-your-volvo-hard-shifting-you-should-read-this/ Check this out, and also have a look through the comments section.
hi im euwing i have a volvo s80 t6 2002.Every time i drive i loose power .can someone help please
Can it be the gearbox or sensor
lalla mariscka take your car to an authorized mechanic immediately for diagnosis, this is a dangerous situation. We can't make guesses over the internet.
Hello, i have a same problem with “transmission service requried, in xc90, some times when i driving with 60 miles per hour, this message lighting on. After 60 miles the computer finding the some thing wrong with automatic, please can you tell me, what s wrong with my car?
It's impossible to say what's wrong with your car with this information. The first course of action would be to have the car scanned for fault codes. If there are codes, you can go from there.
thank you for the video,its great! my volvo 2000 V70 does not go into either of the gears, could it be the same issue please?
Got 2005 xc90 Will It work if i get It from a volvo car .
good tip ok guy thanks
My car is having these symptoms but doesn't have the error message. It's goes limp after trying to find the proper gear
Clogged filter, poor fluid.
Is the harness necessary to replace?
What is the original number for this part?
I have tcm 002f and in place in screen in place of D R N i have this - ? Can it be from the sensor or change or transmission ? I have xc70 2,5 t 2006
Lock-up solenoid does not work.
Poor quality transmission fluid.
Mechanical fault in the transmission
Also the filter is clogged. Need to drill the case and poke the filter. Tap and insert bolt.
my problem is when switching from D to N, then the dash shows R. If i want to really switch to N, then i have to move to R and then backwards to N.
When the dash shows 'R', is it actually in reverse or is it in Neutral? If you are getting inconsistent sensor readings, check to see if you can loosen the nuts and move the switch over slightly. If you are still getting the issue, changing the sensor may be a good next option.
eEuroparts.com in Neutral. Thanks for the suggestion
Hello everyone I have an volvo s80 2005 and the transmition doesnt work the engine start properly but when I put D the car doesnt move. Can anybody help me please?
what did you do to fix it? I have the same problem.
Please I have Volvo S80 D2 automatic gearbox the gear shifts but car doesn't move or drive
what did you do to fix it because I have the same problem
Would you happen to know if this switch is in roughly the same area for an S40 2005?
Yes, they have the same transmission, but ancillaries may be different
Is 0a31 code the same as this code?
Volvo s80 2001 6 plugs non tubor. Fault code: TCM 000B (Shift selonoid valve S1). Please help.
There are a number of solenoids and valves internally that often get gummed up with lack of oil changes. If one become sticky they have to be cleaned taken apart and inspected. If not ok , replaced.!
There’s plenty of video blog on these transmissions, with luck in English or Eastern European Language. Just tap the gearbox model number in (usually a plate in on top or around the transmission) Utube it.
Best way to get a decent glimpse of the Model , take a photo by phone. Zoom in and read the Model number of the gearbox. One number this way or that shouldn’t be a great difference. These solenoids sit on the VaLve body, that can be strip clean out off the gearbox…usually.
How do you replace Output speed sensor kn 1999 volvo s70?
Thanks for the video can just clean it without taking out or replacing
We have heard of people cleaning the contacts, but the switch is held together with rivets rather than screws that must be drilled out in order to open. Most would opt to just replace the switch.
I switched out mine but now the car won't shift out of park. Please help.
Did you buy the correct part number for your car? Is the linkage correctly engaged?
Is there a separate reverse switch on this gearbox?
Only for the reverse lights.
bad PNP sensor causes TCM comunmication error ??
I think I am having the same transmission problems you have. Were you able to find the problem?
I have a P0740 code. I replaced the PNP sensor and it worked fine for a few minutes. Now it won't shift.
@@chcros i had a bad relay in cem
@@chcros i had bad relay in cem .
Would it fix p0810 error?
Is it the same steps for a xc90 t6 with a 4t65e?
It seems pretty similar if not the same.
Mine got the same problem to got transition service required
This prevents the car from being started in gear
Why there is 3 options in PNP switch part ?
There are numerous versions of this transmissions, as the updated and changed through the years
Can u provide to the part?
What to do with tcm 0100?
Is this a 2004 S60?
2002
This is a 2002
Thx!
Bro if you put the vehicle shifter into a low gear you would have had an easier time with the 17 mm bolt (Under the shifter lever)
Just remove the central selector nut first, 13mm, and then the 17mm is out in the open.
wow, a 10-minute job. they want to charge me $1500 for this
You pay for the time it took to build the skills, not the time it takes to do the job.
5:32 🤤
My car shifted gear
Is this a problem
ulises G kkkkkkkkkkkkkkkkkkkkkkkkkkk
Damn. Maybe next time take the candy wrapper off of your microphone before you record a video.