Just built the same thing pretty. I was suprized at the performance difference after direct soldering the motors. Super fun build. Does the elrs version of the x12 have camera pads? I got the pnp version and had to use the mobula 6 camera plug that it comes with.
If you just rock the connector back and forth with very little force, the pins will snap off clean at the board. I have similar setups using the HM X12 board, it takes seconds to remove the plugs, flip the board upside down and solder to clean pads.
NICE!!! I may have already asked you this, but how are you liking the tx12 with AG01’s? I’m flying a Mambo and Tango 2, but both are having gimbal issues, and I’m running out of patience waiting for TBS to get their v2 gimbals out.. I like the form factor of the Mambo, but I’m needing a radio that has more support. IE edge tx. Thank you!
Hi, ag01 is the best, once you try them you will never want to fly TBS sticks again, they will fill very cheap like a plastic toy, and yes TBS tango/mambo is a mess with calibration. Try Zorro/Tx12 on ag01 minis, you will be happy I think.
У меня свои отношения с проводами. Мне дьявольски везёт, но я каждый раз жду, что очередной эпизод станет тем самым, где 800 оборотов вокруг своей оси и замена рамы.
Dude this flies so great, I'm don't have the words
Just built the same thing pretty. I was suprized at the performance difference after direct soldering the motors. Super fun build. Does the elrs version of the x12 have camera pads? I got the pnp version and had to use the mobula 6 camera plug that it comes with.
Yes, ELRS version have camera pads www.happymodel.cn/index.php/2022/04/05/x12-aio-5-in-1-flight-controller-built-in-12a-esc-and-openvtx/
Great job on the video. Amazing how well a 1s quad can rip it would be super fun to race these.
What kinda flight time you getting? I just ordered a 2" apex toothpick frame from pyrodrone. Going for something similar to this.
How hard was it to remove the motor connectors?
Its not hard at all. Firstly just remove plastic with some pliers, then you can cut pins and desolder remains.
If you just rock the connector back and forth with very little force, the pins will snap off clean at the board. I have similar setups using the HM X12 board, it takes seconds to remove the plugs, flip the board upside down and solder to clean pads.
I will build a hand full of these! So fresh!!
I did a similar build with 22000kv motors and twiglet mini frame. really rips, i have a couple of videos of it
On the video there is an OSD element for Amp draw (in your lower left screen). Is that per esc or total amps?
its total
NICE!!! I may have already asked you this, but how are you liking the tx12 with AG01’s? I’m flying a Mambo and Tango 2, but both are having gimbal issues, and I’m running out of patience waiting for TBS to get their v2 gimbals out.. I like the form factor of the Mambo, but I’m needing a radio that has more support. IE edge tx. Thank you!
Hi, ag01 is the best, once you try them you will never want to fly TBS sticks again, they will fill very cheap like a plastic toy, and yes TBS tango/mambo is a mess with calibration.
Try Zorro/Tx12 on ag01 minis, you will be happy I think.
@@LeshaRodin you rock. Thank you so much!!😎
Bret Sanderson
7 hours ago
What tune is this?
?
Hi, uavtech toothpick preset 4.3bf
Привет, а что за батки используешь?
Да gnb разных номиналов
Концовка норм)))👍
Круто!
Поседел, пока считал, сколько раз ты пролетел мимо провода
Так это элемент трассы
У меня свои отношения с проводами. Мне дьявольски везёт, но я каждый раз жду, что очередной эпизод станет тем самым, где 800 оборотов вокруг своей оси и замена рамы.
What tune is this?
UAV Tech Toothpick preset bf4.3.0
20 A max current, so 5 A ESC's do work but never 🐢 😂