I like the fact that you upgraded with normal speakers, sounds strange to say that, haha. But so many other people upgrade their parts of their vehicles with the most expensive, fancy, lights, blah blah blah. Its nice to see someone that has video with normal and affordable upgrades.
Thank you for this video- I was able to replace my front passenger door speaker with very little difficulty, and hardly any swearing. And I have no skill. You did a great job teaching me!
Good video on door panel removal, Crutchfield is the way to go and they send you brackets and adapters to go from car speaker harness to back of speakers for free
2:47 to get this out you need a pick tool and pull it from the top left (opposite side from where you go) it just pops out then and won’t snap the angled clips.
Hey bro greetings ..nice job with the old housings ,,doing the same thing but one quw=estion is it important how you connect the wires to weld them to the old harness i mean plus or minus or that doesnt matter
I've started getting a rattle in one of my speakers at certain frequencies so this will be really helpful when I decide to address it. Should I just swap the one bad speaker or do you recommend upgrading all at the same time?
Most of the speakers for sale come with a set of two so I’d suggest doing two at a time! There is a nice pickup in audio quality so I’d just do em all like that 👍🏼
Hey dito hope you doing well! Nice tuto as always ! No news form the modeo/ imported fusion I just have to wait the fusion come to USA to France with ship and other stuff before I can drive it ahah I wish you the best for the new year and to your belong hope 2023 will be great for you
Thank you so much bro, I’ve been trying to find how to change them out, my speakers rattle a lot I have a 2016 Fusion SE.. this helped a ton! Are the speakers you bought good in bass and everything else? Or should I go for a more pricey one?
Been working in getting those bolts out in the car door but my tools aren’t loosing the bolt at all both the smaller and big one will an impact driver drill get them out easier?? (note I twirled around with my 10mm and my 5.5mm for almost 2 hours was only able to get 2 small ones out)
I will say my fusion isn’t as clean as yours looks wise and literally (it’s filthy lmao) but I have two soundstream 12 inch subs 2500 watts a piece 5k amp in the trunk and the door speakers are absolutely shot, definitely have some serious foam rot so thank you for your informative video, I’ll check out crutchfield for sure
Hey Dito, not really to familiar with sodering the wires the speaker, any tops? I want to replace my speakers in my 2015 fusion with the same ones you got.
Sure! So main thing is just you want to make sure you’re making clear contact between the pieces. So aim to get it more centered and build up some around it so that it’s secure. Then from there you can wrap some electrical tape around it for extra security and then you should be good 👍🏼
I like the fact that you upgraded with normal speakers, sounds strange to say that, haha. But so many other people upgrade their parts of their vehicles with the most expensive, fancy, lights, blah blah blah. Its nice to see someone that has video with normal and affordable upgrades.
Thank you for this video- I was able to replace my front passenger door speaker with very little difficulty, and hardly any swearing. And I have no skill. You did a great job teaching me!
Good video on door panel removal, Crutchfield is the way to go and they send you brackets and adapters to go from car speaker harness to back of speakers for free
They’re so helpful for sure!
Great video. I really like how you soldered the two wires to the new speaker. Genius!
2:47 to get this out you need a pick tool and pull it from the top left (opposite side from where you go) it just pops out then and won’t snap the angled clips.
u have a video of how u took the housing off? i came across that problem, even bought brackets an that didnt work
ford loves those 5.5mm bolts, its also the size of the adjuster on a final gen vic
Hey bro greetings ..nice job with the old housings ,,doing the same thing but one quw=estion is it important how you connect the wires to weld them to the old harness i mean plus or minus or that doesnt matter
Did you end up upgrading the tweeters as well?
I've started getting a rattle in one of my speakers at certain frequencies so this will be really helpful when I decide to address it. Should I just swap the one bad speaker or do you recommend upgrading all at the same time?
Most of the speakers for sale come with a set of two so I’d suggest doing two at a time! There is a nice pickup in audio quality so I’d just do em all like that 👍🏼
Hey dito hope you doing well!
Nice tuto as always !
No news form the modeo/ imported fusion I just have to wait the fusion come to USA to France with ship and other stuff before I can drive it ahah
I wish you the best for the new year and to your belong hope 2023 will be great for you
That’s still exciting that it’s going on, thanks so much man! I hope this year is awesome for you!
Can you make a video recommending alternative radios for a 2014 Ford Fusion se hybrid
Oooooo new video 🖤🖤🖤
I have subscribed because I have 2019 and I’m trying to trick it out black and purple
Thank you so much bro, I’ve been trying to find how to change them out, my speakers rattle a lot I have a 2016 Fusion SE.. this helped a ton! Are the speakers you bought good in bass and everything else? Or should I go for a more pricey one?
What solder did you use
No tweeters?
Been working in getting those bolts out in the car door but my tools aren’t loosing the bolt at all both the smaller and big one will an impact driver drill get them out easier?? (note I twirled around with my 10mm and my 5.5mm for almost 2 hours was only able to get 2 small ones out)
What did you do to your door handles to make them black did you wrap them
Is it a hybrid
Oof that's a beautiful fusion though haha do u still have it?
I will say my fusion isn’t as clean as yours looks wise and literally (it’s filthy lmao) but I have two soundstream 12 inch subs 2500 watts a piece 5k amp in the trunk and the door speakers are absolutely shot, definitely have some serious foam rot so thank you for your informative video, I’ll check out crutchfield for sure
Hey Dito, not really to familiar with sodering the wires the speaker, any tops? I want to replace my speakers in my 2015 fusion with the same ones you got.
Sure! So main thing is just you want to make sure you’re making clear contact between the pieces. So aim to get it more centered and build up some around it so that it’s secure. Then from there you can wrap some electrical tape around it for extra security and then you should be good 👍🏼
I'm giving up my 2014 Fusion 🥺😭. It was a great ride at first but too many problems towards the end 😮💨
What about the tweeters
Arghh i was hopeing it would show me the posative and neg lol but diffrent to my uk 1993 escort haha
Yo! You gotta react to clawboss'es fusion, it's sexy af
what drink was that