Easy Self Leveling Underlayment- Tile Coach Episode 17
HTML-код
- Опубликовано: 5 ноя 2018
- Join us as we show the easy way to install a self leveling underlayment on a kitchen floor. The self leveler is an easy way to make your floor flat and level prior to tile installation.
Watch us prep the floor and mix the SLU to the manufacturer recommendations. If your floor is out of level, this is way easier than trying to build up and level as you install the tile with thinset mortar.
For video on how to do a tile floor layout please watch: • Tile Floor Layout and ...
For video on how to do pebble tile shower pan, check out this one:
• Easy Pebble Tile Insta... - Развлечения
Self levelers are tricky. Probably the best tool in the shed is a garden rake. Use the back side to pull the leveler around over the whole floor, then use the spiky side to keep breaking the surface tension of the leveler until all ripples are gone - it'll be glass smooth. Also, make sure you use a surface primer if the product says to... you'll regret it if you don't (don't ask how I know this! :)
Putting down leveler tomorrow, I have the exact same concrte puller Issac used but I'm going to grab my rake and pull it with the spiky side! Thanks so much for the tip .. even 2 years later!!
@@snoodle877 Thanks for the input... What kind of Leveler is everyone using? Thanks
@@dwaynerobare1153 mapai leveler plus, from lowes
@@snoodle877 how’d it go? I started installing lvp in my living room and noticed its not sitting flat so now i know my subfloor is uneven. I’ll be taking it off and putting self leveler wherever it needs it. I’m hoping it’s just some spots and not the whole living room. Any advice?
@@imartinez92 Thanks for asking! it was almost perfect … but I ran 2 1/2 bags short! Couldn’t believe it! Floor is nice and level but I do have these transitions from 1st pour to final fix. I’m putting Ditra over all so I’m hoping that with a level floor those minor transitions won’t affect my tile lay down.
wow, expansion form as a dam, THAT is a trick I haven't seen before and this tip alone made this a worthwhile video. Thank YOU!!!! Excellent!
I worked for Issac for 2 years. Very impressed with his knowledge and quality. There will always be a “know-it-all” in the comment section of any channel. Please make your own video if this is you. I really can put to use this installation of the level quick to any job benefit from it thanks to videos like this. Thanx Issac
This is a public forum know-all, and you are not a dictator in here, probably not even in your own kitchen, gobshite.
Relax.
The comment section can be priceless. Many share their experience and reflect on what is seen in the video. Like AJ7's post for example.
As a DIYer I'm grateful for the video AND the comments.
Liar 🤥.
@@MyGoogleRUclips SHUT UP!!!! he is right!!!
@@MyGoogleRUclipslol limo
Wow, thanks a million. Using the foam insulation all round is genious, alot less hassle than nailing baseboard trim and silicone all round. And using a window squeegee to help spread the "batter" is a great tip. My project is to use this materialt to underlay for tile in the kitchen cabinet "hole" where the range was at 7/8 inch below the floor tile level. Much better than buying a huge heavy cement board, especially when you only need a 30in x 30in piece.
thanks for the tip about using a trowel to spread the compound.
I usually red guard any cracks before the self leveling underlayment. Great work 👌🏾
You're a GREAT teacher. I love how you were clear and concise, got straight to the point, and down to business. Appreciate you!
You're the best! Great videos with common sense explanations. Thanks a million.
Yo I’m a 22 year old tile installer all your videos help a bunch, haven’t came across too many floor prep videos
Great vid. Love the planning ahead with the marks on the floor.
I always appreciate people like you man
Isaac; Thanks man! I WISH I had caught this before I just used a lot of un needed thinset to build up a "level" corner of my tile project...Proves to me the need to seek out your solid how-to's before diving into a project all gung-ho. I did do that last summer when I had a different project but this time around I was in too much of a hurry. Speed is costly. Big thumbs up!!
Hey guys. Just wanted to say thanks for the video and tips. We just poured a self leveling floor in our kitchen and "butlers pantry". It went great. Thanks again.
@@TileCoach in all fairness, I probably overdid the great stuff but, that's on me. Lol
Dude you rule. Extremely logical approach, very helpful!
We mixed quickset when i was younger and layed marble floors for uneven floors. We would use a long level to see what part of a room was lower, chalk where was lower, pour quickset, smoothen it out, take lunch to let it harden then come back to start popping chalk lines. Perfect quick fix
I love the bags on the feet. Ingenuity....working with what you got. Good stuff thank you for sharing
Perfect timing of this video! Thanks for uploading. Exactly what I needed.
I Understand the principle of what your doing. The Best Tip you gave and it is so simple to wrap your legs up in plastic bags to keep you clean That is so simple! a Great tip to Keep Clean
I love your work and your explanation. Thank you it’s very understandable.
When I saw you setting up multiple mixing buckets so you could pour the leveler all at once, I said "Ah Ha! that's what I need to do for a one man 80 sq ft. floor that 1" out of level.". Thanks for the great idea!
Thank you for video! It's a "one shot" application, so its nice to see it done.
Thanks for this video! I've got a 2 car garage floor that has kind of sunk in certain places. Self-leveling compound like this is perfect for something like this.
I wonder if it is strong enough to take the weight of a car tire (assuming a car ever gets in the garage). Maybe a special leveler?
The spike roller makes it get to level faster. It never "Self" levels all the way. The spike roller breaks that surface tension and gets the job done! Good videos. Thanks!
Do you absolutely need the spike roller or can u do it good enough with a squeegee
Thank you coach! That bag trick is exactly what the dr ordered!
I like to use my green 360 self leveling laser to make my layouts. I’ll take some screws and set them in different spots. To be a better visual representation when pouring the leveler. Love watching your videos. Thank you for doing your thing!! Tile-Doc out
Hey! I used this trick to level my bathroom floor! It works!. Thanks. Levelquik sets up quick tho. Then I just cut the foam flush with a multitool.
So glad I found your video. I want to tile my bathroom but was pretty disheartened when I found how uneven it was. This helped give me confidence and make a plan. Cheers.
How'd your bathroom turn out?
Wonderful video - and loved you new "boots" You helped me appreciate what it takes for a really flat pour.
you are awesome. simple and straightforward.
May God bless you
Heck yeah! Good job man.
Love the spray foam tip. Very nice
Thanks , I wore them bags over my sock walking to school in Nebraska during the winter as a kid ! Actually it was bread bags !
Great video, I’m getting ready to use self leveling compound for the first time. I like your style and clear explanations, you’ve earned a subscriber. Just one thing...don’t vote your heart, vote using your brain. Emotional decision making is not the way to run a country 😄
Paul G
Learn from me. Do a trial section somewhere harmless to make sure you get the consistency right and you get familiar with the technique.
I didn't...
Look out for the sell by date on the bags. The stuff ages and sets up much faster and doesn't flow. Adding water after doesn't help either.
Otherwise you'll end up like I did at 2am knees down with a belt sander trying to make the best of a bad job.
Interesting using expandable foam. Edge ban makes something similar but this method is cheap and effective. Love it
Very helpful, thanks for making this!
المرجو الاشتراك بالقناة والضغط على الجرس ليصلك كل جديد وفرجة ممتعة
Please subscribe to the channel and press the bell to receive all new and fun watching
ruclips.net/video/9Rh5MxZPMcI/видео.html
Great video. Don’t worry about the bagshoes, improvisation is a gift. How long does it typically take for a self-leveler to dry? Could you show how you actually determined the high and low points with your level and straight edge? Also, thanks for sending out love and sharing your positive attitude.
I self level a whole lot different than you do. But I’m open to learning better or different ways for better or similar results. Thanks for the videos.
Great video . great work extra detailed nice job 👍
thank you was able to use this clip to help with my construction course
You guys are the best 🤙👍
Great tips and tricks bro thanks following your directions 💯
duuude. great job, thanks for the lesson, best vid ive seen of this.
you are a hero! great video!
Thanks for the vid. Helped me out a lot
I wish there were experts like you in our area.
Thanks for taking the time to help the rest of the world...will be using all your techniques today!!
I do enjoy the vids!👍
JUST WHAT I NEEDED...THANKS ALOT.
Well Isaac you become really good at :)
Very helpful thank you for the tips.
Thank you very much: exactly what i was looking for.
New subscriber, great content, learning a lot.
Great job
Isaac, I silicone horseshoe spacers to the floor to show the height I need to pour to. Once all my horseshoes are slightly covered I know I'm flat and level!
I have been using a similar trick with backer board screws to set my heights....
@William may it's "you're" not "your" and you call Isaac retarded?
Good idea. I would use a wood screw and easily adjust the height. Going to do this next time I run into this thanks guys
Great idea. I think I can visualize it. Who will provide a video showing the spacer technique?
ProTileGuy thanks for the tip!
great video
Thank you so much! I will be doing my bathroom this week to prep for tiling. After putting down mortar and then cement board screwing it down its still uneven-old home 1930. Thanks again!!!
in the old homes its better to just go with the flow of the house. Mine was the same way. It was flat but everything sloped towards the middle. I used the uncoupling membrane and tiled it no problem
I use that same Marshalltown rake or spreader too. I picked it up out of necessity one day and it works really well.
@@TileCoach Yep. I use both. The rake to move it around and then the spiked roller to break the surface tension and get it to flatten out.
Isaac Ostrom the roller is good for merging pours from different buckets. The stuff dries so fast merging pours don’t always “level” perfectly. The roller kneeds it together better then pushing it around with a squeegee.
thanks and I love the bags
Good stuff. I would like to see you using a gauge rake but it looks good!
Thanks this is awesome.
Good video. Very helpful.
المرجو الاشتراك بالقناة والضغط على الجرس ليصلك كل جديد وفرجة ممتعة
Please subscribe to the channel and press the bell to receive all new and fun watching
ruclips.net/video/9Rh5MxZPMcI/видео.html
And thanks for the great video.
Great work bro thanks for
Very good video. Thank you
Absolutely the best “self leveling” video I have seen. Thank you for taking the time to share.
No. The best self levelling videos will show the use of spiked rollers.
Foam spray
GENIUS
What name brand self leveling compound do you recommend, or will any type do?
Thank you...
Showing how you used the level and the straight edge. To get your "ground zero" and different depths would of been helpful. Otherwise awesome.
And the way you calculated volume from the point measurements.
Small rotary lazer level at the high point, measure down with your tape measure from the level line, then measure at random points around the room and superglue shims or packers up to the correct height. Then you pour the compound level with the top of the shims/packers 👍
Just pour it... forget the measurements..
How would you handle cracks in the slab under the self leveler? Would you fill those with epoxy, or just prime them and fill them with the self leveler?
Great Tip Thank You
The leveler was wetter then what I’m use to, and mixing enough for the whole pour upfront. I see now that these are important steps. The end result was impressive
Have you tried using a porcupine roller when pouring leveling compound? It works great at blending all the poured material leaving a glass finish. I typically grind the humps using a cup wheel with a hepa vac, then it minimizes the amount of material needed.
I am about to use self leveling concrete on my bathroom floor I have radiant to go over which is in half-inch plywood tracks can the self leveler go directly onto the plywood or should I put some sort of a membrane like tarpaper down first and then the self leveler
Do you have to do the foam edging when doing laminate floor planks?
great video..
Very good Video!
Great video! That is exactly how I level floors!
Awesome!
Great Video
Nice video! How do you now or control the depth of the cement your pouring?
Vote absolutely! Educate yourself and help others!!!
Thanks issac!
Good stuff.👍
@3:35 I have made the exact mistake that you are describing here. I have found that even if I poured two buckets next to each other the edges of those two pours would not blend by themselves. There was an "edge" to where those pours met, due to the surface tension.
If I could do it again I would use garden rake to blend the separate pours. The spike roller is probably the best tool for it, but a rake would probably work too.
with self levelor you have to be fast and the mix must be runny. If you pour on top of the previous pour you run the risk of the first one setting up (which happens within about 5min) and then getting humps in your finished product. I try to pour each bucket in a way that it just touches the edge of the previous one and then check it with a straight edge and laser level if needed. Concrete nails are useful to set your heights before you start but many other things work just as well.
Use a spiked roller, and the pours all blend like magic, provided of course that your material is still runny (not starting to set).
Good video! For concrete do you go back and resaw in the control joints in the slab?
Hey looks good. I use 8in floor grinder with vacuum, it gives more tooth for the floor lever material. Then I prime. Try a plastic leaf rack does real way. But has always you do great work.🤛
Plastic leaf rake sounds like a great idea. I watched another video where the installer used a spiked roller. As a DIY'ER who only needs to install Self-leveling once or twice, using the plastic rake I already own sounds like a great low cost alternative. Thank you for sharing your tip.
المرجو الاشتراك بالقناة والضغط على الجرس ليصلك كل جديد وفرجة ممتعة
Please subscribe to the channel and press the bell to receive all new and fun watching
ruclips.net/video/9Rh5MxZPMcI/видео.html
You are absolutely correct, self leveler is much better than using thinset as a build-up which I've been guilty of before, would have taken me 20 bags on that job to set tile using thinset😨
I will essentially do what he does with thinset when they cant a Ford 20 bags of self level it's easy saves time and money
Yea, I followed someones advice about using thinset to level the floor, what a waste of time and money, project did not turn out good. Going to prime tile, pour underlayment, and put down a floating vinyl plank.
Thinset $16... Self leveler$35 you crazzy
Draconic Windbane if they can’t a Ford self level they can’t Chevy me.
Carlos Cantu I’m $65 an hour. Self leveler is cheaper.
Can this be used on top the durock and tile after
Thank you
Isaac , I like the way you said, we are mixing the self leveler , you watch while the poor guy done all the mixing, Okay you did spread the stuff, but still it was a good video, well done.
Awesome thanks
Good Info!
Check out leveling with tripods, makes it pretty easy for this as well as a spiked roller and spiked shoes for walking in it while its wet. Spiked roller helps to level and get the air bubbles out at the same time. Cheers
Absolutely agree about the spiked roller and shoes. Once you try with these, you will NEVER go back to doing without. The difference is huge. The spiked roller continually breaks the surface tension, and the product flows like magic.
HEY I HAVE a question so i ripped up my carpet so i can tile a few spots underneath have old 6os laminate tile and some painted area do i need to use an acid or conditioner to pull up the old adhesive ? after i pull remaining tile? then use a primer then level?
I have a question I am about to use high end vinyl floor planking on a concrete slab the room is like couple feet below grade. Now existing are 9x9 anyway some are missing what would be best way to even floor.
Great video Isaac! I have a small room (115 sf) in a 200 year old house ... I will be putting down natural slate. I have demo’d about 2-3/4” of old flooring layers down to the original floor boards that I will leave in place. The floor is about 3/8” out of level. I plan to first put down 1/4 Luan and then use a leveling compound. Is that ok over plywood? When I get the floor level I plan to install 3/4 ply, 1/4” Durock, then slate. Do that would like a good plan to you? Thanks very much for any help!!!
المرجو الاشتراك بالقناة والضغط على الجرس ليصلك كل جديد وفرجة ممتعة
Please subscribe to the channel and press the bell to receive all new and fun watching
ruclips.net/video/9Rh5MxZPMcI/видео.html
what did you use to get your high spots marked out? a 6" level or a few straight edges?
Glad I found this. Getting ready to put wood laminate in my living room but the concrete slab is cracked bad and is uneven. This beats grinding the peaks down and crack chasing.
I would like to see the floor after you pour it with a level. To make sure it's flat.
Thank you for sharing. Would you like to answer my question ? Can I use this method to level a floor for tile-over-tile. If so, should I use self leveler before the primer or after?