Jason, thank you so much for posting this, wouldn't have got one without this video! Such a cool add on. For anyone considering one, here are a couple tips that may help: a. The wire that goes through the firewall is relatively delicate (4 tiny wires inside) - be very careful pulling/pushing this through: you're in trouble if you break a wire - whole infotainment display WON'T work! Same if you unplug the camera. The extra grommet hole can certainly be used but recommend cutting the nipple inside the cab - just pull with some pliers and slice it off. Also consider gently slicing the grommet hole with a small knife - just a little, maybe 1/4". Will retain its shape but way easier to get the dongle through. Don't force the wires. b. tightening the camera nut is a huge pain. Test fit the nut on the camera before trying to install - mine was partially cross threaded from factory. It is pretty much mandatory to remove the upper portion of the grill like Jason did - be very careful if you've never done this before. You have to remove the 6 or so plastic fasteners and 1 bolt. But what you can't see are about 6 interlocking tabs that hold the bottom part of the upper grill to the top part of the lower grill/bumper. You'll need to get a very small flat screwdriver and separate the tabs one by one. You have to pull the upper grill FORWARD to the front to release it. DO NOT PULL IT UP like many videos show. You might get lucky and have the tabs self separate but likely you'll break one/some - ask me how i know. With the upper grill removed, the nut can be accessed. c. consider some automotive cloth tape over all connectors/wires in the cab, zip ties have a tendency to rattle.
People ask for more high-end quality vehicles with fancy interiors but nothing is better than a toyota super easy and snaps back on!! And wallahhh!! Your done ✔️
How about a step further and do a 2nd front facing from underneath? Useful for wheel placement and rock bash consideration. Would need a toggle for the video feed switching.
So it did not interfered with your pre-collision/radar system? Did you test drive and check your radar/pre-collision sensor? I've seen other youtube video where they installed the camera on the side of the sensor. I'm not liking it not on the center. LOL. Thanks. Great job!
No issues with the placement. Sometimes the camera itself is glitchy when it’s very cold (or hot) outside. Radar, pre collision, adaptive cruise all work as normal. But only do what you’re comfortable with.
Your video is the only one that doesn’t push the rca into the cab. After watching all the others I was scrambling to find out way they were doing that. It just doesn’t make sense because that rca I’d for inside the cabin. Thank you for confirming that.
Hey Jason, I went to order this kit from Cali Raised for my 2018 4Runner Limited. Your discount code isn't working. I presume it must have expired and wanted to let you know in case you can get it renewed. I'm not handy and don't have the tools it takes to do this, but there's a car audio shop near me that installs aftermarket backup cameras and navigation systems that will do a professional job with this. In my research before buying the 4Runner I'd seen one of the newer off road models that had a front bumper camera. It looks like an essential item for off roading, particularly if you're going to be driving on your own without a passenger who can get out and be a spotter when there are obstacles. And as you say, it's also good for everyday driving and parking. I'll wait until later in the day or tomorrow to order this from Cali Raised in case you see this and are able to renew the discount code.
Yeah Colorado’s are harder in this case. Chris and I were chatting about it and this was the best option I could find. Not 100% sure it’d work: www.gm-navigation.com/shop/2019-and-up-chevy-silverado-and-gmc-sierra-camera-module/
Installed and worked GREAT.... for a while. Now it blacks out once it gets too hot. Currently looking for a new camera or a way to keep it from getting too hot.
I installed this and it works great however I noticed when I switch from front camera, to reverse, i get a horizontal split screen where it shows the bottom half of the rear cam on the top. And the top half on the bottom (if that makes sense). Anything I did wrong? I checked the wiring and ground and everything seems correct. Not sure if I need to cut another wire since I have an aftermarket HU? (T8)
Its occasional and to get rid of it I have to hit the button from front to rear super fast almost like I have to confuse the system to get the rear cam back to normal view
My 2022 had the MTM it was very helpful. I really hated that hood scoop, it reflected sun rays. Do your backup/front camera lines turn with the wheel? That blank space was where my camera button was. The crappy rhino about MTM is it turns off at certain speed.
It is a game changer we have one and had several friends give us heck for it. They called it cheating for off-road. LOL I told them i was an old school gamer and wasn't beyond cheat codes. After one of them got one for themselves they were blown away and said they weren't going back lol.
There’s no such thing as as cheating when it comes to safety for you and your passengers. Why take a risk of trashing that beautiful beast. I’ve been on many trails that make this a bonus.
Any Idea why the 2015 back up cam works intermittently? I just purchased mine, it worked when I drove it out of the dealership but they gave my no warranty.
Sorry, not sure. I'd check the wire harness on the back of the head unit. The head unit itself might be going bad? I've noticed glitches sometimes when its extremely cold outside.
This video got me excited! However I found that it is not compatible with 4Runners with a 3d Camera. The 3d camera system already has a camera placed on the front bumper. Too bad there isn't a way to utilise it as a front facing off road camera and not just for 3d (bird's eye view) purposes.
@@JasonExplainsThings Sorry, I should have explained better. I have a Sony XAV-AX100. But if I recall it only has one input for a camera. But I'd really like to be able to add a front camera and have the rear on demand. Thanks!
Big enough annoyance with the factory rear camera, but isn't the front camera going to get non-stop dirty with the slightest amount of stuff on a road and a car in front of you?
Tried to get our ORP ordered with the MTM camera system, but no way in my area given the vehicle supply chain problems :-(. Looks like a great alternative, thanks for the video! Do the lines overlayed on the front camera picture seem calibrated like the rear view camera, i.e. the outer blue line is 3 feet from an object and the red line is 1 foot?
I’m not sure how accurate they are honestly. BTW… I was in the same boat ordering a Tacoma. Tried to get the camera system but it was impossible without getting a fully loaded truck with leather and everything else. So I’m going to be doing this camera again.
For a 2017 this is not good I've, been looking at wires for the last 3 hours and trying to map them to your tutorial an have had no luck. Maybe for 2021 specifically this is great but im having a ton of trouble.
Jason, thank you so much for posting this, wouldn't have got one without this video! Such a cool add on. For anyone considering one, here are a couple tips that may help:
a. The wire that goes through the firewall is relatively delicate (4 tiny wires inside) - be very careful pulling/pushing this through: you're in trouble if you break a wire - whole infotainment display WON'T work! Same if you unplug the camera. The extra grommet hole can certainly be used but recommend cutting the nipple inside the cab - just pull with some pliers and slice it off. Also consider gently slicing the grommet hole with a small knife - just a little, maybe 1/4". Will retain its shape but way easier to get the dongle through. Don't force the wires.
b. tightening the camera nut is a huge pain. Test fit the nut on the camera before trying to install - mine was partially cross threaded from factory. It is pretty much mandatory to remove the upper portion of the grill like Jason did - be very careful if you've never done this before. You have to remove the 6 or so plastic fasteners and 1 bolt. But what you can't see are about 6 interlocking tabs that hold the bottom part of the upper grill to the top part of the lower grill/bumper. You'll need to get a very small flat screwdriver and separate the tabs one by one. You have to pull the upper grill FORWARD to the front to release it. DO NOT PULL IT UP like many videos show. You might get lucky and have the tabs self separate but likely you'll break one/some - ask me how i know. With the upper grill removed, the nut can be accessed.
c. consider some automotive cloth tape over all connectors/wires in the cab, zip ties have a tendency to rattle.
All great points!
Thanks Jason! Just installed same camera on my 2021 4Runner TRD Pro. Was a breeze following your video! Works great! Thanks again!
Awesome! It's a great addition. I use it all the time.
People ask for more high-end quality vehicles with fancy interiors but nothing is better than a toyota super easy and snaps back on!! And wallahhh!! Your done ✔️
YES! Couldn't agree more.
How about a step further and do a 2nd front facing from underneath? Useful for wheel placement and rock bash consideration. Would need a toggle for the video feed switching.
my 2022 sr5 premium only has a rear camera, so I can share your dream. I am going to seriously consider doing this!
Nice, yeah the install would be exactly the same as on my 4Runner.
I have often wished I could also toggle the camera without putting the vehicle in reverse, very cool!
Very Helpful! Thank you Jason ! I have been thinking about it for a while. What do you think about installing parking sensors?
Just in time for my 2021 4Runner. Good job!
Nice. I would move the wire you put under the carpet though. Extra wear and tear on the insulation from getting stepped on
It’s right around the edge so that won’t be a problem. 👍
So it did not interfered with your pre-collision/radar system? Did you test drive and check your radar/pre-collision sensor? I've seen other youtube video where they installed the camera on the side of the sensor. I'm not liking it not on the center. LOL. Thanks. Great job!
No issues with the placement. Sometimes the camera itself is glitchy when it’s very cold (or hot) outside. Radar, pre collision, adaptive cruise all work as normal. But only do what you’re comfortable with.
Your video is the only one that doesn’t push the rca into the cab. After watching all the others I was scrambling to find out way they were doing that. It just doesn’t make sense because that rca I’d for inside the cabin. Thank you for confirming that.
Hey Jason, I went to order this kit from Cali Raised for my 2018 4Runner Limited. Your discount code isn't working. I presume it must have expired and wanted to let you know in case you can get it renewed. I'm not handy and don't have the tools it takes to do this, but there's a car audio shop near me that installs aftermarket backup cameras and navigation systems that will do a professional job with this. In my research before buying the 4Runner I'd seen one of the newer off road models that had a front bumper camera. It looks like an essential item for off roading, particularly if you're going to be driving on your own without a passenger who can get out and be a spotter when there are obstacles. And as you say, it's also good for everyday driving and parking.
I'll wait until later in the day or tomorrow to order this from Cali Raised in case you see this and are able to renew the discount code.
Looks like they changed it on me! It's now: JASONEXPLAINS
@@JasonExplainsThings Thanks. I'll put in an order and use the code.
Thanks! This help this channel keep going!
Thank you for making this video!!! Great job explaining everything.
I would like to be able to put three cameras. one in front, two others in the right rearview mirrors looking backwards.
If this works for the Colorado, I’m buying one. Can’t wait to see the video.
Yeah Colorado’s are harder in this case. Chris and I were chatting about it and this was the best option I could find. Not 100% sure it’d work: www.gm-navigation.com/shop/2019-and-up-chevy-silverado-and-gmc-sierra-camera-module/
Installed and worked GREAT.... for a while. Now it blacks out once it gets too hot. Currently looking for a new camera or a way to keep it from getting too hot.
Same here. Intermittently it has issues. If I find any solutions I’ll share them.
@@JasonExplainsThings I'm thinking of trying to wrap the wires in aluminum tape for heat resistance
Do you know if there is one for 2012? I also have an aftermarket pioneer head unit
I installed this and it works great however I noticed when I switch from front camera, to reverse, i get a horizontal split screen where it shows the bottom half of the rear cam on the top. And the top half on the bottom (if that makes sense). Anything I did wrong? I checked the wiring and ground and everything seems correct. Not sure if I need to cut another wire since I have an aftermarket HU? (T8)
Its occasional and to get rid of it I have to hit the button from front to rear super fast almost like I have to confuse the system to get the rear cam back to normal view
When do you install the dog palace in the 4Runner?
Toby's too tough for palaces!
I'm assuming you would have mentioned this, but it doesn't interfere with the safety sensor stuff in the front in any way?
Nope.
He did mention that it doesn't interfere with it in the video
I gotta get me one of these kits!! Thanks for making this video!
It’s holding up great.
My 2022 had the MTM it was very helpful. I really hated that hood scoop, it reflected sun rays.
Do your backup/front camera lines turn with the wheel?
That blank space was where my camera button was. The crappy rhino about MTM is it turns off at certain speed.
No the lines aren't dynamic. They're more a rough guide. I agree with the hood scoop issue. I may install something to fix that soon.
Any idea if there would be an issue with the JBL set up? I have a 2019 Limited that I would love this for.
Shouldn’t be an issue. For 2019 just make sure you get the 2014-2019 kit.
@@JasonExplainsThings awesome. Thanks for the prompt reply too!
It is a game changer we have one and had several friends give us heck for it. They called it cheating for off-road. LOL I told them i was an old school gamer and wasn't beyond cheat codes. After one of them got one for themselves they were blown away and said they weren't going back lol.
Nice Jeremy! I love considering them off-road cheat codes. I'm going to have to use that.
There’s no such thing as as cheating when it comes to safety for you and your passengers. Why take a risk of trashing that beautiful beast. I’ve been on many trails that make this a bonus.
@@Fozzi1-1836 agreed and it's s joke among us
No, it’s my Colorado that needs one!😀
Well I just bought this thanks for the video
Went to install lol and pulled alittle to hard and the wire snapped in half. Thank god I know how to soldier. Camera flickers a bit but it will work
So how i can install my 4runner 2020 limited ,cause looks different of front side but i already ordered , thank you
Should be the exact same process. I’d confirm compatibility on their website
Any Idea why the 2015 back up cam works intermittently? I just purchased mine, it worked when I drove it out of the dealership but they gave my no warranty.
Sorry, not sure. I'd check the wire harness on the back of the head unit. The head unit itself might be going bad? I've noticed glitches sometimes when its extremely cold outside.
This video got me excited! However I found that it is not compatible with 4Runners with a 3d Camera. The 3d camera system already has a camera placed on the front bumper. Too bad there isn't a way to utilise it as a front facing off road camera and not just for 3d (bird's eye view) purposes.
You'll be fine with the factory camera system. Here's a video all about it's features: ruclips.net/video/8GY9pXBwidM/видео.html
So THAT'S what that button does. And I still look forward to more of your vidoes, thanks!
Good job my friend . Is this available for 4RUNNER SR5 2015 ?
Yep! The 2014-2019 kit should work
Noticed your 2021 isn't push button start?
Yep.
would love info on the head unit youve got installed, looks like a tacoma head unit. Did you do this aftermarket?
Nope. It’s the premium audio/nav factory head unit
Installed mine. Cut the white wire (front facing camera). It’s still showing reverse video. So frustrating. Any thoughts?
I’d reach out to the manufacturer. Sorry you’re having problems.
@@JasonExplainsThings I’ve tried but they won’t return my emails
Nicely done sir, CAMERAS!
Is this or something similar available for 4th gen 4runners?
Tying into the stock head unit would likely be an issue. You'd probably need to get an aftermarket head unit as well that would work with the camera.
@@JasonExplainsThings Sorry, I should have explained better. I have a Sony XAV-AX100. But if I recall it only has one input for a camera. But I'd really like to be able to add a front camera and have the rear on demand. Thanks!
Big enough annoyance with the factory rear camera, but isn't the front camera going to get non-stop dirty with the slightest amount of stuff on a road and a car in front of you?
Not really honestly. The rear camera gets dirty much faster. I think as long as you're not tailgating others it's not really a huge issue.
Tried to get our ORP ordered with the MTM camera system, but no way in my area given the vehicle supply chain problems :-(. Looks like a great alternative, thanks for the video! Do the lines overlayed on the front camera picture seem calibrated like the rear view camera, i.e. the outer blue line is 3 feet from an object and the red line is 1 foot?
I’m not sure how accurate they are honestly. BTW… I was in the same boat ordering a Tacoma. Tried to get the camera system but it was impossible without getting a fully loaded truck with leather and everything else. So I’m going to be doing this camera again.
Yeah, I know. And Canadian version of 4runner off-road (2022) has it. 😂
So well done! Thank you.
For a 2017 this is not good I've, been looking at wires for the last 3 hours and trying to map them to your tutorial an have had no luck. Maybe for 2021 specifically this is great but im having a ton of trouble.
Check the description. The kit for 2019 and back is different.
Will this work on 2010 if cruiser with aftermarket head unit ?
You’ll want to find something that’s made to work with your aftermarket head unit. This is designed to work with 4Runner factory head units
Does this interfere with 12voltsolutions remote start
I haven’t messed with remote start.
Need one for my Tacoma :)
Let's do it!
@@JasonExplainsThings I ordered one, used your JasonExplains5 discount code :)
Great Video Jason Thanks 🙏 man
Hi Jackson!
Very good
Hi, need help in my camera, pls share contact to brief my issue with Front camera installation.
Beyond the video I'd suggest contacting Anytime Backup Camera for assistance.
Funny guy. We don’t like those 22
nobody likes their oil too thick!