We are required to weld 3 4x4x1/4 each same were just talking about you canadians lol they just started making us paint our drivers door white but I've seen many people around here loose doors and get pulled out hope they ALWAYS HOLD FOR YA
We use the belts to keep the rad In place it works well it gives it play but wow they hold your trunk and doors were allowed 3 3in welds per seam.and 4 3in on the trunk but were just starting to run Camry's we used to and still.use mostly Cavaliers gm.products
thanks man and i think it is one of the most built ones i have made still a bit more to do cage o the floor and doors and driver door tie rods back window bar
I have not had any issues with any bolts snapping yet the cage has been in five cars now over a span of two years it's a advantage because you never waste steel and it installs so quickly
Do you modify the rims lug pattern to fit on your cars? I usually run luminas and Buick’s but I’ve only run stock donuts on back. I’m looking to run much smaller tires such as those 8’s you showed. Any suggestions would be appreciated thanks and keep up great vids man
Hey Zack love the channel, have watched every Camry video and was just wondering what you typically pay for one out your way. There’s a couple out here in Nova Scotia but they seam pricey! Keep up the good work and can’t wait to see this yota get trashed!
depends on alot of things 4 or 6 cylinder auto or manual and distance from my house and how rusty they are and of course if they run and drive or not 500-150 is what i pay for them most i spend around 300-400 but some do go higher some are lower but over the scrap yard scles i get 300 for them so i dont lose alot of money
zacks workshop I’m looking at around 600-300 in my area . Can’t derby due to some health issues this year but will be on the hunt for some camrys this fall/winter. Thanks for the reply !
The bumper rule is bs. You should just get a steel 80s rear vic bumper and put a square tube in it then fold the sides over they might tell you to cut a holes in the sides thrill show only look for light on the other end
zacks workshop there only picky with people they don't know very well I seen way too many things go just because they know them but I still don't think they would find the tube in the bumper
zacks workshop that's bs I See cars that don't bend like in tillsonburg on cars front never moved and he used it the hole time but you must be on there bad side lol
We are required to weld 3 4x4x1/4 each same were just talking about you canadians lol they just started making us paint our drivers door white but I've seen many people around here loose doors and get pulled out hope they ALWAYS HOLD FOR YA
well thanks for watching chris and around me rules change event to event
We use the belts to keep the rad In place it works well it gives it play but wow they hold your trunk and doors were allowed 3 3in welds per seam.and 4 3in on the trunk but were just starting to run Camry's we used to and still.use mostly Cavaliers gm.products
i am allowed to weld as well but i just belt it has never gave me any issues
That car looked badass!
what car ?
Cannibal
Use seat belts and spray foam from that civic rad it works great!
i love seat belts
Cool Video Like Video Zacks Workshop
thanks cole
Looks sick
thanks i put alot of effort into it
Aside from skids and maybe creaseing the front its probably the meanest yota iv seen you build
thanks man and i think it is one of the most built ones i have made still a bit more to do cage o the floor and doors and driver door tie rods back window bar
Never seen a rear camry bumper come off I've seen them break in half but never come off
ya i seen that now too
workshop can you look up Ford mustang derby car and watch it
there is alot of videos of mustangsin derbys
Whats the pros on a bolt in cage. I feel like the bolts would snap when the car starts to bend
I have not had any issues with any bolts snapping yet the cage has been in five cars now over a span of two years it's a advantage because you never waste steel and it installs so quickly
I have a question zack is derby season over for you in Canada
pretty much yea
Awesome video Zack the car look sick
thanks i have alot of effort into it
you should get a Ford mustang in the next video
if i get one u will be the first to know
@@zacksworkshop171 ok
Do you modify the rims lug pattern to fit on your cars? I usually run luminas and Buick’s but I’ve only run stock donuts on back. I’m looking to run much smaller tires such as those 8’s you showed. Any suggestions would be appreciated thanks and keep up great vids man
i remove every thing in the back every thing to fit the 8s in the back
Are the back wheels off of a baler?
no small trailer tires
Ps u still doin derbys in Canada with covid our season just started
every event is canceled up here
i have a toyota camry 2001 model no spark no start. please assist
what did u do
Do you prefer the earlier 90s or late 90s
i like 97-99 but they is not ALOT of differences between them i find the newer ones have more power
Hey Zack love the channel, have watched every Camry video and was just wondering what you typically pay for one out your way. There’s a couple out here in Nova Scotia but they seam pricey! Keep up the good work and can’t wait to see this yota get trashed!
depends on alot of things 4 or 6 cylinder auto or manual and distance from my house and how rusty they are and of course if they run and drive or not
500-150 is what i pay for them most i spend around 300-400 but some do go higher some are lower but over the scrap yard scles i get 300 for them so i dont lose alot of money
zacks workshop I’m looking at around 600-300 in my area . Can’t derby due to some health issues this year but will be on the hunt for some camrys this fall/winter. Thanks for the reply !
no problem thanks for watching
Yea the name fits
thanks man
zacks workshop I think the 10 inch tires look good on there don’t know why but me personally I like the wide tire look
i like it too makes it look like a race car with the stance
Do you know when the next mud bog is
oct 17 2018 check out moms motor sports facebook page for updates and pay outs
im derbying a hyundai santa fe on it 2nd run
i had no problem and u sure bc mine doesnt
let me know how it goes
@@zacksworkshop171 it went well
Like the name
thanks man
weld um
will do
send it
will be sent
That looks mean
very means
zacks workshop by the way the name is great
thanks man
The bumper rule is bs. You should just get a steel 80s rear vic bumper and put a square tube in it then fold the sides over they might tell you to cut a holes in the sides thrill show only look for light on the other end
i am planning to run with thrill show they have been alot more picky with there rules i been having issues with them this year
zacks workshop there only picky with people they don't know very well I seen way too many things go just because they know them but I still don't think they would find the tube in the bumper
proplem is than they know me lol some people dont like me as well and alot of them say i cheat i had to drill holes in the frame last year in barrie
zacks workshop that's bs I See cars that don't bend like in tillsonburg on cars front never moved and he used it the hole time but you must be on there bad side lol
i dont know why some peoples cars dont bend i build mine to the rules as best as i can and they always go to rat shit lol
Eventually your gonna run out of names
not if people keep giving me good ideas lol
zacks workshop true
Now i know why these cars are disappearing
Yep I have wrecked 40 of them but hoesntly if I did not do this they end up at crush yards any ways