I have blinking yellow light on gps switch. as you say it indoors at this time . I need to see if it change to green outside today.if it work I will not upgrade the gps unit.
I did exactly as you explain in this Video Clip (3D-»ATTI=1400) so it was expected that my FW450 would actually maintain the Altitude BUT THAT IS NOT HAPPENING. If I don't control the "altitude" with the Colectivo, the Heli will fall to the ground. Can my Friend give me an explanation for this? Thank you very much for your attention. Mario
I know this is old, but just came up on my feed. I’ve got my switches up GPS, middle ATT, and down 3d… I don’t really see the need for return to home, I never fly so far away that I lose perspective
I have changed my 3D mode to ATTI mode on my H1 by setting a value of 1400 to the 3D switch position instead of 1000, it worked but I have 1 issue and don't know if it's a normal condition, in all other filght modes swash plate is level in ATTI mode the left side cyclic servo drops about 4mm wich also tilts the swash to left roll. Is this a normal condition on the bench?
Been trying this on mine but atti seems just like 3d to me as mine will drop if not fast enough on the left stick she doesn't stay at any hight but is spot on in gps
@CRUZROYHelicopters doing that right now lol. Seems to gain a bit of collective between gps and atti that normal ? It sure didn't climb last time between gps and atti gps is rock solid All looks good gonna try
Ok tried it again in just gps all is still good but I think I damaged the belt last time it came down fast I switched back and gave it up it made a unhappy noise I suspect a few belt teeth are gone
If it is dropping you are in 6G mode you have to go on the software and hit the factory reset button to completely reset the flight controller to get ATT mode especially if your H1 is the heli version but caution when you hit the factory reset make sure that you have either wrote down or took a screenshot of all your previous parameters and swash plate numbers before you hit that factory reset Hope that helps you
Now when you get done setting to factory default settings in 2.0 and you get all your parameters and everything reset when you get done have it in 3D mode which is the blue light if the tail motor does not start when you unlock it then you have to go to version one 1.81 and restart the tail motor in that version I know it's crazy but I've been through all this that's how you have to do it if your tail motor starts in 3D mode then you're fine
In the FUNCTION...does Throttle Mode need to be set to: Self Centering -or- Non self-centering ???
Where do I find that software/ Thanks for the video.
Can you lift off in ATTI mode and while airborne switch over to GPS?
Yes you can. During flight , you can switch over between the two, no matter if you lift off with GPS or ATTI.
You going to make a flight, with the changes?
I have blinking yellow light on gps switch. as you say it indoors at this time . I need to see if it change to green outside today.if it work I will not upgrade the gps unit.
Or go into h1 software and recalibrate your unit. “Last page”
Thanks!! What exactly is ATTi mode, as compared to 3D or Normal or 6G? I hear about ATT in different places but I don't quite get it yet. :)
its 1400us its between GPS and home mode, its stable without the gps , so it will stay level but drift
I did exactly as you explain in this Video Clip (3D-»ATTI=1400) so it was expected that my FW450 would actually maintain the Altitude BUT THAT IS NOT HAPPENING. If I don't control the "altitude" with the Colectivo, the Heli will fall to the ground. Can my Friend give me an explanation for this? Thank you very much for your attention. Mario
Friend you and me both
I think we got to change the pitch setting their is a difference when you switch between the two ?
What is ATTI MODE? Also, please give me a down and dirty tutorial on binding my Flysky FS-i6s Radio from my 450 to the FlyWing BELL-206 Thanks
you have to add models, that radio only has 5
ruclips.net/video/nk7eCR0-OtI/видео.html
once you follow the add model video, follow this one to make settings the same . ruclips.net/video/zpkp5G-IZyI/видео.html
atti mode, is heli will keep height but lose gps
I know this is old, but just came up on my feed. I’ve got my switches up GPS, middle ATT, and down 3d… I don’t really see the need for return to home, I never fly so far away that I lose perspective
Don't forget that RTH will activate automatically if the battery power gets too low during flight, a good safety feature.
I have changed my 3D mode to ATTI mode on my H1 by setting a value of 1400 to the 3D switch position instead of 1000, it worked but I have 1 issue and don't know if it's a normal condition, in all other filght modes swash plate is level in ATTI mode the left side cyclic servo drops about 4mm wich also tilts the swash to left roll. Is this a normal condition on the bench?
what does the 1000, 1300, etc even mean? can someone explain what that value indicates?
These are specific numbers that act like an electronic tag to the flying mode they are assigned to.
Been trying this on mine but atti seems just like 3d to me as mine will drop if not fast enough on the left stick she doesn't stay at any hight but is spot on in gps
need a computer and a good outside calibration
@CRUZROYHelicopters doing that right now lol. Seems to gain a bit of collective between gps and atti that normal ? It sure didn't climb last time between gps and atti gps is rock solid
All looks good gonna try
Ok tried it again in just gps all is still good but I think I damaged the belt last time it came down fast I switched back and gave it up it made a unhappy noise I suspect a few belt teeth are gone
each time i put mine in atti mode it drops from the sky have to put more up on controller yes blinking red
If it is dropping you are in 6G mode you have to go on the software and hit the factory reset button to completely reset the flight controller to get ATT mode especially if your H1 is the heli version but caution when you hit the factory reset make sure that you have either wrote down or took a screenshot of all your previous parameters and swash plate numbers before you hit that factory reset Hope that helps you
@@danduer1174 thanks will do taken all photos and will reset it next week after fun fly week end xx
And I also forgot to mention my friend when you go on the software it has to be version 2.0 software
@@danduer1174 ok thanks again for reply will look what vir iv got doing it next week
many thanks x just looked yes got vir 2.0
Now when you get done setting to factory default settings in 2.0 and you get all your parameters and everything reset when you get done have it in 3D mode which is the blue light if the tail motor does not start when you unlock it then you have to go to version one 1.81 and restart the tail motor in that version I know it's crazy but I've been through all this that's how you have to do it if your tail motor starts in 3D mode then you're fine
I did the factor reset now gps and atti have no difference like it did like yours i think mine is set now will try tomorrow