Thank You for the video. I have to replace the board and thought I would have to remove the generator. Great video. My problem is the gen would run for anywhere from a few minutes to a few hours and then shut down. code 36. The carb bowl was empty. first thought was fuel pump so I replaced it but had the same problem. I stripped off a small area on the fuel pump wires and hooked my meter up so I could watch the voltage while it was running. I cranked it and watch for about 10 minutes. The voltage to the pump started out at 14V. After a few minutes I saw it start to drop slowly. It went from 14, 13, 12 etc. all the way to less than a volt. Course the pump cant run off that so the gen shut down due to lack of fuel. I''m pretty sure its the circuit board so I'm going to research a bit more before I order one.
THIS IS HOW I FIXED MINE, IN THE CASE OF.... "I CAN'T START MY GENERATOR" It's has been two years since last time it was running, so I started by checking oil level full at gen dipstick (it won't start if low oil because of sensors) then I checked gasoline more than 1\4 tank in the RV (also safety sensors), sparkplug checked for good spark, also checked the manual reset circuit braker ( to be ON) at front motorhome engine compartment for 12v current to the generator to be able to start it, also cleaned the carburetor and even installed new one but same situation, then checked wires and found some has been chewed like gum by rats at the back of starting switch generator panel so I replaced them, at this time the generator started but stay running only by keep pushing the switch on all the time, so then finally I knew it was internal electrical problem from the engine itself, so I took the generator out from my RV to work in my garage, (I did this by myself with some tools and old Mayan tricks ) lol, it's really heavy for one person. I disassemble the unit at my garage and started by removing the cover, then the cooling fan or flywheel unit (it's 2 items in one) until finally I was at the gen rotor and brushes assembly area and this is what I found: one more wire chewed by filthy rats plus the stinky rat nest in the middle of the generator motor coil, I fixed the wire and sanded the commutator copper contacts where the brushes are sitting becouse they were real duty with old urine from the rats, and of course I got rid off the stinky nest, lol!!! Then I assembled everything back together and... bingo it's runing like a champion!!! For this project materials involved was about $60.00 including an aftermarket new carburetor and an harmonic balancer/steering wheel puller (available at any auto parts for $25.00) to pull the aluminum fan out and (flywheel). Just picture this: (Any gasoline engine run smooth if gasoline and DC current aren't interrupted) so following this important principle you'll always find the problem to be fixed. Also if you have a onan microlite 4000 like mine, don't run it for more than a minute without the cover because you'll cook the engine real fast, also keep the eye on the aluminium fan and your fingers after cranking it in case you missing one or two members...just kidding, lol!!! After testing the gen with the help of a gasoline container, a piece of hose and 12v battery, I did put the air cooling assembly back and the rest of components including the cover, then it was ready to be installed at my RV. Once the gen was installed back at my motorhome I started it to be tested for 120v electricity but not before flipping the AC circuit switch (on) at the gen starting control panel (sometimes hiding under or around the panel) to be able to transfer power to my RV GFCI main outlet and electric panel as well, my motorhome it's equipped with GFCI so I reset it and tested for green led light indicating power is ready at my main breakers panel, so I turned my main breaker (on) along the others ones but no power was present at my breaker main switch (faulty main braker) so I flipped it many times, sometimes you can make it work again, mine did work, lol!!! I'm happy because everything works now including the refrigerator for cold drinks and AC for this crazy summer, lol! Later I'll buy me a new main braker, for now this is a resurrected generator story that needed to be shared. If this can help eaven one person to save time and $$$ it'll make me more happy, thanks for reading!
Thank you so much just purchased a 5th wheel used with this generator been trying to figure out why I have no 12v power to unit for starting and priming. Come to find out its missing its control board
Sorry I had just decided to put a couple vids onto RUclips, so I know it’s been a while but my generator wouldn’t connect to the trailer meaning the transfer switch wouldn’t switch. Sorry this took so long
Thank You for the video. I have to replace the board and thought I would have to remove the generator. Great video. My problem is the gen would run for anywhere from a few minutes to a few hours and then shut down. code 36. The carb bowl was empty. first thought was fuel pump so I replaced it but had the same problem. I stripped off a small area on the fuel pump wires and hooked my meter up so I could watch the voltage while it was running. I cranked it and watch for about 10 minutes. The voltage to the pump started out at 14V. After a few minutes I saw it start to drop slowly. It went from 14, 13, 12 etc. all the way to less than a volt. Course the pump cant run off that so the gen shut down due to lack of fuel. I''m pretty sure its the circuit board so I'm going to research a bit more before I order one.
So was it the board? Mine is doing the same thing.
THIS IS HOW I FIXED MINE, IN THE CASE OF....
"I CAN'T START MY GENERATOR"
It's has been two years since last time it was running, so I started by checking oil level full at gen dipstick (it won't start if low oil because of sensors) then I checked gasoline more than 1\4 tank in the RV (also safety sensors), sparkplug checked for good spark, also checked the manual reset circuit braker ( to be ON) at front motorhome engine compartment for 12v current to the generator to be able to start it, also cleaned the carburetor and even installed new one but same situation, then checked wires and found some has been chewed like gum by rats at the back of starting switch generator panel so I replaced them, at this time the generator started but stay running only by keep pushing the switch on all the time, so then finally I knew it was internal electrical problem from the engine itself, so I took the generator out from my RV to work in my garage, (I did this by myself with some tools and old Mayan tricks ) lol, it's really heavy for one person.
I disassemble the unit at my garage and started by removing the cover, then the cooling fan or flywheel unit (it's 2 items in one) until finally I was at the gen rotor and brushes assembly area and this is what I found: one more wire chewed by filthy rats plus the stinky rat nest in the middle of the generator motor coil, I fixed the wire and sanded the commutator copper contacts where the brushes are sitting becouse they were real duty with old urine from the rats, and of course I got rid off the stinky nest, lol!!!
Then I assembled everything back together and... bingo it's runing like a champion!!!
For this project materials involved was about $60.00 including an aftermarket new carburetor and an harmonic balancer/steering wheel puller (available at any auto parts for $25.00) to pull the aluminum fan out and (flywheel).
Just picture this: (Any gasoline engine run smooth if gasoline and DC current aren't interrupted) so following this important principle you'll always find the problem to be fixed.
Also if you have a onan microlite 4000 like mine, don't run it for more than a minute without the cover because you'll cook the engine real fast, also keep the eye on the aluminium fan and your fingers after cranking it in case you missing one or two members...just kidding, lol!!!
After testing the gen with the help of a gasoline container, a piece of hose and 12v battery, I did put the air cooling assembly back and the rest of components including the cover, then it was ready to be installed at my RV.
Once the gen was installed back at my motorhome I started it to be tested for 120v electricity but not before flipping the AC circuit switch (on) at the gen starting control panel (sometimes hiding under or around the panel) to be able to transfer power to my RV GFCI main outlet and electric panel as well, my motorhome it's equipped with GFCI so I reset it and tested for green led light indicating power is ready at my main breakers panel, so I turned my main breaker (on) along the others ones but no power was present at my breaker main switch (faulty main braker) so I flipped it many times, sometimes you can make it work again, mine did work, lol!!!
I'm happy because everything works now including the refrigerator for cold drinks and AC for this crazy summer, lol! Later I'll buy me a new main braker, for now this is a resurrected generator story that needed to be shared.
If this can help eaven one person to save time and $$$ it'll make me more happy, thanks for reading!
thank you I need to change motherboard was thinking had to remove generator until I saw your Video much appreciated
Thank you so much just purchased a 5th wheel used with this generator been trying to figure out why I have no 12v power to unit for starting and priming. Come to find out its missing its control board
Great vid, how do you know if your motherboard is bad?
Sorry I had just decided to put a couple vids onto RUclips, so I know it’s been a while but my generator wouldn’t connect to the trailer meaning the transfer switch wouldn’t switch. Sorry this took so long