David Thanks for the video. The area we live in I may need to unhook chiller and put in the garage for a couple of weeks in the winter, have you looked into using camlocks ?
Incredible build man. I thank God I’ve waited to pull the trigger on ice barrel until now. I’m going with the 500 and following this exact advice. Thanks!
Three things I would do differently 1. Use plumbers tape on all threaded connections. 2. - use plastic connectors vs brass or metal if possible. 3. Put a ball valve inline before the filter to allow clean out
Loving my active aqua 1/2hp chiller paired with the 1000gph pump. Total game changer compared to my last chiller/pump combo. Hottest part of the day and it was only 2° away from set point of 45°. My last setup with the same tub would be 52-53° by about the same time.
Ok....Barrel 500 is on the way and should be at my house next week...Can not wait! I had already purchased all the items in your description from Amazon and used your discount to get an additional $189 off the Barrel (thanks for that). I am setting up in my garage gym and will also need to make sure there are no leaks. Literally like a little kid on Christmas morning! Thanks again for all the great videos.
I appreciate this so much!! I’m doing this setup with the 300!! ( patiently waiting for it to ship) but in the meantime I’ve got the 1/4 horse active aqua going into a shitty cold pod and it’s holding temp at 42 f!! In salt lake with 100 degree weather!! Impressive
I ended up doing this DIY. I added another filter after the pump. it's working great. Thank you very much for creating this DIY video man. great stuff on here!
Love the build! If I may suggest, in order to pump out the water faster put the T at the outlet side of the pump. With the spigot open then plug your inlet side (with the black male 3/4 plug that the 500 came with) from the inside and it will empty your 500 in no time. I did this with my over complicated build along with a garden hose and I water the plants and grass with the water. Another tip is to get a threaded and barbed combo 3/4 for the inlet side to your hose connection to lower the profile and hug the barrel better. Just my 2cents on your awesome channel. Love the content brother.
Thank you for this video! I am going to run with this set up opposed to the other set up. You are the man! Hope you get to the 100 thousand subscribers soon!
This was super useful for me as my first chiller just died on me and I have to redo my setup. The only thing I'd recommend adding is a shut off valve in between the T connector and the filter so you can clean/replace the filter without having the water drain out. Otherwise I'm following your instructions exactly 👍
Another great tutorial. I have the OG IB400 set up more like your original build. I had issues with leaks and noise from the aqua pump, so set it up like your original build with the green filter sitting inside the barrel as well. I would much prefer to keep everything outside of the barrel so that I can move my arms and legs around without bumping anything but am going to enjoy the experience and leave it as is until I change the water. I love the insulation with this model though, so I'll have some thinking to do and may have to start putting a little money to the side for an “upgrade.” The 400 sweats quite a bit. Not sure if you've seen DIY Cold Plunge but he put out a plan for adding another ozone and filtration set up. I have that going as well which really seems to be helping keep the water clean. I have it set on a timer for 30 minutes every night but based on what you mentioned, I might cut that back to maybe 15 minutes a night or every two or three nights.
I just wanted to say thank you for your extreme detail. Laying everything out in such a way that we can see it and understands how things are physically working is awesome. For me you took all the guesswork out of actually getting this done. Not sure if you have any idea of the cost to run a tub for a month, I know there are many variables (what tub, where...in sun out of sun...etc, how big of a pump and chiller, where you live such as Florida, in my case the ridiculous California)...but, any estimated range would be good to know. Thanks again for the info.
Thanks for the love and support! Surprisingly I have multiple tubs running 24/7 and dont see any major noticeable difference in my power bill. I could find a way to test it but with a family of 6 and the doors always open my bill was high before hooking these up and its about the same now :)
I have the 1/4 hp and the daner 950. Just waiting for my IB 500. I did build a ozone into my filter system. Just a preference after messing with water challenges in my last cold plunge. Excited to get it all set up
I've read that ozone can damage certain types of rubbers and plastics but I rarely see it discussed with cold plunges. Have you looked into this at all?
I did some research and there isn't any info that says ozone is a risk to cold plunges. It could be a risk to a chiller though so I have mine after the output of the chiller just to be safe. I will monitor and remove the ozone if it is ineffective or causing any erosion. It's a good call out. I am not 100% confident but there are lots of people who use them with no complaints.
Awesome! That topic is always tricky. Ozone works well, but its not needed all the time. That is why I jsut use an ozone generator when the water looks or smells like its getting bad and I run it for an hour. If i built on in i would probaby only run it for 15-30 mins in the middle of the night.
I would recommend a 90 elbow on the inside of the ice barrel to redirect the outflow from the pump. That Danner pump will blast you in the face otherwise.
Hi David. In checking out on the Ice Barrel 500, they have a charge for $89 for VIP protection. I could not see any way to edit this out or what they mean by protection damage and loss. I would appreciate your feedback. The video said that it would bring the cost down to $1300 but currently with the $89 charge it’s 1400+. And thank you for your authentic service. I can’t wait to build mine!
I’ve never heard of that. I bet it’s like a fee to make up profit margins. No idea but I’m sure we will be seeing that pop up on all of them soon. Especially with all the shipping damages that have been happening
Awesome video David! Appreicate you breaking everything down step by step and providing the part list. Very helpful! I'm new to the DIY cold plunge set up, and was hoping you, or anyone else on the thread could answer a couple questions for me. Is it necessary to always keep the water pump running, or its it best to set the pump and cooler on a timer? Do you have to unplug the equipment before getting into the cold plunge (i.e. risk of electrical shock), since the pump and cooler are outside the unit? How loud would you say the Danner 950 water pump is when running? Any help would be greatly appreciated! Thanks!
@davidmausjr how are you ensuring the cords do not get wet? should i make sure the fill level is correct? is it okay for the cords to get wet from water overflow and rain outdoors i guess?
Dave, what’s up with Ice Barrel? Communication is horrible. After watching this video I decided on the ice Barrel 500 and ordered it over a month ago and still haven’t received it. Do you have any direct communication with Ice Barrel?
Same here. I ordered the Ice Barrel 500 in June 2024 and I still don't have the product (9/9/24). Now I have to research and order another cold plunge from a different company. I must have sent Ice Barrel around 13 reminder emails. I've been in contact with Gillian and Payton, but they are way too slow in responding. I appreciate David promoting Ice Barrel, however, I would stay away and look for another company. Ice Barrel has the worst communication and now I need to get my money back. Such a waste of my time.
Have you ever tried adding epsom salts or anything like that to enhance the therapy benefits with the plunges? For the last month it was cold enough to still use my rubbermaid I started adding epsom and found it beneficial. See others in the r/coldplunge talking about putting dead sea salt in theirs.
I see you’re pushing the 1/4 hp chiller. Tell me this, how long does it keep the water at the 3degree leeway before it kicks on? Does the chiller run once an hour for 15 or so minutes or does the insulation keep it cold to where the chiller runs once every two hours ?please and thank you
Hello I have a question what would be the best way to connect the ozone bubbler into this setup? Can I drop it from the top and still close down the lid?
I am looking to have the pump, filter and chiller in another room that shares a wall with the ice bath. Would I be able to run about 24” of 3/4” pipe out of the bottom drain, run in thru that wall then hook up into the filter, pump and chiller? I am guessing it wouldn’t be a problem but I wasn’t sure if the pump works best directly attached.
How well did the 1/4 hp chiller end up working?? I live in a very hot climate and have the 500. I ve been doing weekly costco trips for ice but i am looking at getting a chiller at some point. Great video and walk through.
its working like a champ! still in the same spot, baking in the FL sun and ive been impressed. Keeps the temp right on the number for me. I keep it all on 24/7 but the chiller kicks off when reaching the temp
Excellent David! - thanks for making this. I'll most likely get this done for my Ice Barrel 300 - since i have mine in my garage, you're thinking the 25 HP is plenty right? I try to stay around 45 degrees - thanks
David, quick question I live in the state of Kentucky. Do you think any of the components would freeze and bust? If so should I unhook the chiller in the winter?
Hey Dave, just bought mine. Have you looked into whether is possible to side mount the components on the side of the ice barrel 500 like the Desert Plunge does? Asking because I like how clean the cord management is as well as the addition of an automated ozone device.
I wouldn’t use a tee. I would just use a valve before the strainer to allow for strainer cleaning without draining barrel. I would also use pipe dope or teflon tape on each fitting.
Incredible timing - just found out my Ice Barrel 500 gets delivered in 1 week (after weeks of waiting) and was getting ready to pull the trigger on your previous setup! Love your videos, thank you so much for all the great content. Quick question - I live in Boston which means over the winter it's regularly below freezing. I plan to have an outdoor setup. Will I only be able to use this chiller in the warmer seasons (ie will it freeze outside?) Any advice for chiller for someone in my area who has to deal with freezing temps?
I have been watching a lot of your videos on all of the different tubs and versions, Ice Barrel, MOD, Desert, Plunge. So i am looking for some advice on what to buy, budget $3000, I am 55, 5’11” 269pounds looking to use this as therapy as I have auto immune issues that we are managing naturally as all of the medicine version side effects have made me feel worse. I have been plunging for the past 14 days every day in trough. Water temp from 38-51 degrees depending on day. Worse part seems to being sitting on metal on ground after initial shock. What would you suggest?
Awesome! I think I will purchase the 1/4 as you mention and you did state you keep it outside. Do you cover it at all for rain or just leave it as is? Due to how you set it up is there any worry of electrocution if you are using a GFCI outlet? I ask since the pump is now external. Thank you!
Does anyone have any suggestions for mats or something to catch the water under the Ice Barrel 500? Does the felt mats work? I was thinking about something like a washer basin, but I don't think they get big enough. Any thoughts?
Hi, How cold does your ice barrell 500 get with the 1/4 hp chiller? And have you tested the 1/2 hp vs the 1/4 hp? I'm looking to get 37 degrees with the 1/4 hp chiller.
@@DavidMausJr Just installed my chiller setup on my 300 today. Followed this exact tutorial, step for step. Works great and saved a ton of space. Thanks again, sir!
Where do you attach the filter? or do you not use one and only rely on the strainer? really love this set up and looking to purchase, just curious on this filter decision. thanks
I noticed that some other DIY options utilize a whole house filter. in this set-up you only show a very small sediment filter. I have an Ice Barrel 300 and have tried it out w/o any pump/filtration and after a few weeks I noticed the water itself stays clear with hydrogen peroxide and a spa water stabilizer/cleaner BUT there appears to be LOTS of small dead skin flakes floating around, I'm concerned with a small pre-filter it won't be sufficient to keep these all at bay. my goal is to change out water as infrequently as possible. I have purchased the DIY set-up....just wondering if I should add a whole house filter in addition to the small sediment filter you show here before putting it all together
Hi, @davidmausjr, I'm hoping you can answer this question for me. I actually referred a few friends to buy this kit on amazon. I'm not sure what's going on w/ my kit, but since I already had the stock tank and chiller (1/3 Hp Arctic Pod), I thought I could easily adapt. HOWEVER, my chiller which seemed to work fine and could chill my previous tub from high 50's to low 40's in just a few hours (using a 200 Gph pump and 1/2" connections), this new setup takes FOREVER to chill the water. The only thing I can think of is the pump is pushing the water through my chiller too fast and I'm trying to figure out how to slow the flow. Your help/advise would be much appreciated!
@davidmausjr thank you for all of your insight. I have procured the IB300. In some of your videos you show a connection to the 1HP AA chiller and in others you talk about going all the way down to a 1/4 HP. I plan to use my IB first thing in the morning so will have the chiller running the night before to get the water temp down. I am debating between the 1/2 HP and 1 HP AA. The setup will be outside in Texas. Thoughts on which one to go with?
Thanks David, great information as always! Hey wondering if there is a way to add a hot water component to this setup to make it a cold/hot setup? Thanks again!
@@jonmkellermy wife’s boss has a chiller hooked up to his hot tub built into the pool. It’s not ideal nor cheap though and takes 24 hours to cool. He only uses it once or twice a week because of that. It’s better to have a dedicated unit.
Hi David. Super informative. I have my IB500 but have not bought the chiller yet. Question: what are the specs for a drain hose to connect to the spigot? My chiller is inside so will need to drain using a hose.
Any idea how well that cooler last outside long term? I’m planning on doing this but I’m concerned how long that cooler will last. Maybe need to build a box to put it in to make sure it last as long as possible.
Hi David . I just moved and had to part with my troth I was using. I was wondering if there is an ice barrel you are not in need of or want to part with it. I live in Florida myself. Please let me know and God Bless 🙏🏼😊
Are the fittings with your DIY relatively universal for other similar tubs with chiller fittings (i.e. redwood outdoors Alaskan cold plunge)? In other words, if I get your DIY package will it be appropriately sized for most other plunges? Thanks!
Yes that should work! The only thing you would have to adjust is the attachment to the barrel, i wouldnt suggest getting all 1/2" parts, just get a thread adapter. This will work: amzn.to/3VWD5Jr
Just finished the setup today! Used a 1HP chiller from Active Aqua… total overkill haha. Big question: what smart devices do you use to turn everything on / off? I don’t really want the pump running 24/7 as this sits in a temp controlled garage. Any thoughts? Was thinking a simple timer but. Just don’t want to mess up the active aqua.
Two questions. How much of the hydrogen peroxide are you adding? And do you have a filter as part of this DIY? Seems like some of your tubs have a 20 micron filter and some do not?
I just did a follow on your Amazon profile. I’m happy to order them through you but if I just going to use my bathtub, can you tell me which items I need? Thank you so much
For sure! You just need a way to keep the hoses inside the water, maybe just using the last connections in a metal material to keep them down? or ziptie them together inside the water
Hey Dave, I have done all the steps and used plumbers tape on everything. I keep having leaks on the bottoms through the rubber washer. Ive tighten it used plummers tape, but it seems to be leaking. Do you have any suggestions on how i can solve this issue?
Super helpful thank you. Quick q - if my pump is submersible only (unlike yours which works external to the tub), how would this impact your setup? Ex: if I ended my exterior setup with the filter like yours, would water still flow in & out of the mesh filter?
Check out the new Kit! DMJR.co/500DIYKit (it will also work better for the Ice Barrel 300)
Is the 300 as insolated as this one? Would the 1/4 HP be enough for that 300 build?
@@andrewclarke8036 It is very similar, but not as much. You may want to up to the 1/2 if you live in a really hot climate
David Thanks for the video. The area we live in I may need to unhook chiller and put in the garage for a couple of weeks in the winter, have you looked into using camlocks ?
also, is there any issue getting the 1/2" danner pump and using 1/2" tubing all around. I think my current chiller is 1/2"
Hey David, thanks for the video! Q: how’s the 1/4 HP holding up since? Would you recommend going up to the 1/2 HP?
You created the video I was searching for thank you for the build, cant wait to get my set up completed !
Glad to help!
Incredible build man. I thank God I’ve waited to pull the trigger on ice barrel until now. I’m going with the 500 and following this exact advice. Thanks!
Three things I would do differently 1. Use plumbers tape on all threaded connections. 2. - use plastic connectors vs brass or metal if possible. 3. Put a ball valve inline before the filter to allow clean out
I dont disagree! Couldnt find the pieces on amazon to do number 2. I totally misses number 3! I may add it when I do a full cleanout
Is there a disadvantage to using metal or brass connections?
@@jodyneffable - I like to know the same thing.
Why is plastic better?
@@Superstar-cl7we homogeneous materials. Better to keep like like
Loving my active aqua 1/2hp chiller paired with the 1000gph pump. Total game changer compared to my last chiller/pump combo. Hottest part of the day and it was only 2° away from set point of 45°. My last setup with the same tub would be 52-53° by about the same time.
Which barrel/tub are you using?
Ok....Barrel 500 is on the way and should be at my house next week...Can not wait! I had already purchased all the items in your description from Amazon and used your discount to get an additional $189 off the Barrel (thanks for that). I am setting up in my garage gym and will also need to make sure there are no leaks. Literally like a little kid on Christmas morning! Thanks again for all the great videos.
Awesome set-up. I'm just getting to the point where I'm ready to get all the goodies ordered for the 500! Thanks again, David!! ✌️
Awesome!!
Thanks for this. Got the pieces needed and will be setting up this week. Appreciated the work you did to make it easy for us.
Glad to help!
I appreciate this so much!! I’m doing this setup with the 300!! ( patiently waiting for it to ship) but in the meantime I’ve got the 1/4 horse active aqua going into a shitty cold pod and it’s holding temp at 42 f!! In salt lake with 100 degree weather!! Impressive
I ended up doing this DIY. I added another filter after the pump. it's working great. Thank you very much for creating this DIY video man. great stuff on here!
Love the build! If I may suggest, in order to pump out the water faster put the T at the outlet side of the pump. With the spigot open then plug your inlet side (with the black male 3/4 plug that the 500 came with) from the inside and it will empty your 500 in no time. I did this with my over complicated build along with a garden hose and I water the plants and grass with the water.
Another tip is to get a threaded and barbed combo 3/4 for the inlet side to your hose connection to lower the profile and hug the barrel better.
Just my 2cents on your awesome channel. Love the content brother.
Incredible idea! Didnt even think of that. Thanks brother!!
I’m not sure I follow - the water would drain through the pump - or we would use the pump to increase drain rate?
Any way you can share some visuals of your set up @kingfish9677
David, you are a legend. This is such a straightforward DIY. Bonus points for the Amazon buy list.
Thank you for this video! I am going to run with this set up opposed to the other set up. You are the man! Hope you get to the 100 thousand subscribers soon!
Wow - great work! Perfect video. Thank you.
Appreciate that!
This was super useful for me as my first chiller just died on me and I have to redo my setup. The only thing I'd recommend adding is a shut off valve in between the T connector and the filter so you can clean/replace the filter without having the water drain out. Otherwise I'm following your instructions exactly 👍
Another great tutorial. I have the OG IB400 set up more like your original build. I had issues with leaks and noise from the aqua pump, so set it up like your original build with the green filter sitting inside the barrel as well. I would much prefer to keep everything outside of the barrel so that I can move my arms and legs around without bumping anything but am going to enjoy the experience and leave it as is until I change the water. I love the insulation with this model though, so I'll have some thinking to do and may have to start putting a little money to the side for an “upgrade.” The 400 sweats quite a bit.
Not sure if you've seen DIY Cold Plunge but he put out a plan for adding another ozone and filtration set up. I have that going as well which really seems to be helping keep the water clean. I have it set on a timer for 30 minutes every night but based on what you mentioned, I might cut that back to maybe 15 minutes a night or every two or three nights.
Insane timing for this video, I was just about to build this kit and was like why is dude talking about an eclipse, this must be old, ha!
Haha! Filmed during it today! 😂
Love the hose filter. I was thinking about that today. Ha I was very close to rerouting my water softener to the exterior to fill mine up.
I just wanted to say thank you for your extreme detail. Laying everything out in such a way that we can see it and understands how things are physically working is awesome. For me you took all the guesswork out of actually getting this done. Not sure if you have any idea of the cost to run a tub for a month, I know there are many variables (what tub, where...in sun out of sun...etc, how big of a pump and chiller, where you live such as Florida, in my case the ridiculous California)...but, any estimated range would be good to know. Thanks again for the info.
Thanks for the love and support! Surprisingly I have multiple tubs running 24/7 and dont see any major noticeable difference in my power bill. I could find a way to test it but with a family of 6 and the doors always open my bill was high before hooking these up and its about the same now :)
Your Channel is amazing and great help
Thank you for making all the helpful videos
Thank you!
I got my Ice Barrel 500 and did the exact setup except with all PVC connections. Thanks for all the info.
Really awesome channel. Glad i stumbled on it. Very cool finding like minded people that make you better! Thanks!
Let’s go! God is good!
He sure is!
I have the 1/4 hp and the daner 950. Just waiting for my IB 500.
I did build a ozone into my filter system. Just a preference after messing with water challenges in my last cold plunge. Excited to get it all set up
I've read that ozone can damage certain types of rubbers and plastics but I rarely see it discussed with cold plunges. Have you looked into this at all?
I did some research and there isn't any info that says ozone is a risk to cold plunges. It could be a risk to a chiller though so I have mine after the output of the chiller just to be safe. I will monitor and remove the ozone if it is ineffective or causing any erosion. It's a good call out. I am not 100% confident but there are lots of people who use them with no complaints.
@@jamieferrazano ww2.arb.ca.gov/resources/fact-sheets/ozone-effects
Awesome! That topic is always tricky. Ozone works well, but its not needed all the time. That is why I jsut use an ozone generator when the water looks or smells like its getting bad and I run it for an hour. If i built on in i would probaby only run it for 15-30 mins in the middle of the night.
Thank you. Excellent setup. It’s warming up and it’s time put a chiller on my IB500. How often do you run the pump/chiller? Do you use a timer?
The danner is an excellent pump. Great choice. They do start to make a weird kind of clicking noise after several months of continuous use though.
Perfect setup with pump just ordered thank you
I would recommend a 90 elbow on the inside of the ice barrel to redirect the outflow from the pump. That Danner pump will blast you in the face otherwise.
It is for sure a rush of water. Lol
Hi David. In checking out on the Ice Barrel 500, they have a charge for $89 for VIP protection. I could not see any way to edit this out or what they mean by protection damage and loss. I would appreciate your feedback. The video said that it would bring the cost down to $1300 but currently with the $89 charge it’s 1400+. And thank you for your authentic service. I can’t wait to build mine!
I’ve never heard of that. I bet it’s like a fee to make up profit margins. No idea but I’m sure we will be seeing that pop up on all of them soon. Especially with all the shipping damages that have been happening
Just bought mine last week! Hopefully it comes soon! Perfect timing
Good choice!
Awesome video David! Appreicate you breaking everything down step by step and providing the part list. Very helpful! I'm new to the DIY cold plunge set up, and was hoping you, or anyone else on the thread could answer a couple questions for me.
Is it necessary to always keep the water pump running, or its it best to set the pump and cooler on a timer? Do you have to unplug the equipment before getting into the cold plunge (i.e. risk of electrical shock), since the pump and cooler are outside the unit? How loud would you say the Danner 950 water pump is when running?
Any help would be greatly appreciated! Thanks!
@davidmausjr how are you ensuring the cords do not get wet? should i make sure the fill level is correct? is it okay for the cords to get wet from water overflow and rain outdoors i guess?
Yes they can get wet (assuming you’re using quality cords) just keep the plugs protected.
Can you have the ice barrel with chiller inside you home? I’ve seen people say they sweat some
Dave, what’s up with Ice Barrel? Communication is horrible. After watching this video I decided on the ice Barrel 500 and ordered it over a month ago and still haven’t received it. Do you have any direct communication with Ice Barrel?
Same here. I ordered the Ice Barrel 500 in June 2024 and I still don't have the product (9/9/24). Now I have to research and order another cold plunge from a different company. I must have sent Ice Barrel around 13 reminder emails. I've been in contact with Gillian and Payton, but they are way too slow in responding. I appreciate David promoting Ice Barrel, however, I would stay away and look for another company. Ice Barrel has the worst communication and now I need to get my money back. Such a waste of my time.
@trinihulk2454 Having the same issue. They took my money and it's been months. Terrible customer service. No communication.
Have you ever tried adding epsom salts or anything like that to enhance the therapy benefits with the plunges? For the last month it was cold enough to still use my rubbermaid I started adding epsom and found it beneficial. See others in the r/coldplunge talking about putting dead sea salt in theirs.
People do it for sure! I havent really tried it in the cold plunge but might have to!
I see you’re pushing the 1/4 hp chiller. Tell me this, how long does it keep the water at the 3degree leeway before it kicks on? Does the chiller run once an hour for 15 or so minutes or does the insulation keep it cold to where the chiller runs once every two hours ?please and thank you
Hello I have a question what would be the best way to connect the ozone bubbler into this setup? Can I drop it from the top and still close down the lid?
Any issue putting the filter in front of the pump ? Can that damage pump pulling water
No issues at all! Works great!
I am looking to have the pump, filter and chiller in another room that shares a wall with the ice bath. Would I be able to run about 24” of 3/4” pipe out of the bottom drain, run in thru that wall then hook up into the filter, pump and chiller?
I am guessing it wouldn’t be a problem but I wasn’t sure if the pump works best directly attached.
How well did the 1/4 hp chiller end up working?? I live in a very hot climate and have the 500. I ve been doing weekly costco trips for ice but i am looking at getting a chiller at some point. Great video and walk through.
Like a charm! No issues at all and always right on my set temp
What was the ozone generator you were talking about? Link please, TIA.
DMJR.co/cleaningkit
do you have an update on how the 1/4 hp pump took to bring to temp in FL temps? how often do you run your pump?
its working like a champ! still in the same spot, baking in the FL sun and ive been impressed. Keeps the temp right on the number for me. I keep it all on 24/7 but the chiller kicks off when reaching the temp
Hey David, how come you aren’t using a home house water filter within your system?
I have one, just a little extra cleaning
Excellent David! - thanks for making this. I'll most likely get this done for my Ice Barrel 300 - since i have mine in my garage, you're thinking the 25 HP is plenty right? I try to stay around 45 degrees - thanks
Totally!
David, quick question I live in the state of Kentucky. Do you think any of the components would freeze and bust? If so should I unhook the chiller in the winter?
If you think the power will go off for a long time then yes, with the water constantly moving you might be ok but most will just unhook for winter.
Gonna be setting mine up indoors is there any condensation build up on the barrel ?
Will the Darren 1200gpm work w the Ice barrel 300 or should I stick to 950gpm
1200 is great but the 950 has been working well too
Thanks man. I really appreciate the walkthrough on this one.
Hey Dave, just bought mine. Have you looked into whether is possible to side mount the components on the side of the ice barrel 500 like the Desert Plunge does? Asking because I like how clean the cord management is as well as the addition of an automated ozone device.
You can totally do that! Just make sure you use a short 1/2” screw. Nothing longer should be needed
Does this setup work on the 400 if you have the new conversion kit they sell you posted about
I wouldn’t use a tee. I would just use a valve before the strainer to allow for strainer cleaning without draining barrel. I would also use pipe dope or teflon tape on each fitting.
I would also use a rubber hose washer on the barbed fitting coming off the pump. My setup is indoors and I needed it leak proof.
Solid ideas!
Can you share a picture of the valve and washer setup?
If you were going to add a 5 micron filter, would you add it before or after the pump?
Before. You want to keep everything out of the pump
Thanks again for the info!!
Totally!!
Incredible timing - just found out my Ice Barrel 500 gets delivered in 1 week (after weeks of waiting) and was getting ready to pull the trigger on your previous setup! Love your videos, thank you so much for all the great content. Quick question - I live in Boston which means over the winter it's regularly below freezing. I plan to have an outdoor setup. Will I only be able to use this chiller in the warmer seasons (ie will it freeze outside?) Any advice for chiller for someone in my area who has to deal with freezing temps?
@sindsy82 My 500 says it was received in Ohio by FedEx on 4/12. Wonder how long it will take to get to Nevada.
Can I use the active aqua on the ice up industry plunge ? And if so what size tubing and attachments will work ?
I’m sure you can, I just need to take a better look at the Ice Up tub fittings.
Let me know when you can i appreciate it! Thanks
when testing the pump for leaks @11:45 why not connect tubing to the pump and dumb it back into the top of the tub?
I have been watching a lot of your videos on all of the different tubs and versions, Ice Barrel, MOD, Desert, Plunge. So i am looking for some advice on what to buy, budget $3000, I am 55, 5’11” 269pounds looking to use this as therapy as I have auto immune issues that we are managing naturally as all of the medicine version side effects have made me feel worse. I have been plunging for the past 14 days every day in trough. Water temp from 38-51 degrees depending on day. Worse part seems to being sitting on metal on ground after initial shock. What would you suggest?
All that you listed are solid options. I’d check out the Desert Plunge Wide. It’s only like $3k with my discount added (MAUS) is the code
Hi I wanted to ask why not all the adapters in stainless steel . I saw you chose some in brass, was that just a preference ?
How many times can you refill your cold plunge with the inline rv water filter? Is it a one use and done product?
About 4 fill ups
Can you post a video of how loud it is? I'm
Considering putting it I doors. Thanks so much!
Awesome! I think I will purchase the 1/4 as you mention and you did state you keep it outside. Do you cover it at all for rain or just leave it as is? Due to how you set it up is there any worry of electrocution if you are using a GFCI outlet? I ask since the pump is now external. Thank you!
The 1/4 HP chiller is taking time to cool it down... been stuck at 80 F for 3 hours. Im in North Texas
Cant wait to get one
Any idea how much electric the pump and chiller use with this set up on a daily basis after the initial cool down?
Pulls between 1-5 amps continuously
For ozone, would you drill a hole, or, world you find a clever t-joint, etc, to plumb it in?
T joint and plumb it out just get an ozone generator and use when needed.
Did you end up plumbing the T Joint? I'm curious to find some videos of people adding ozone to their IB 500
Does anyone have any suggestions for mats or something to catch the water under the Ice Barrel 500? Does the felt mats work? I was thinking about something like a washer basin, but I don't think they get big enough. Any thoughts?
check out this link there is a mat in that people use and love dmjr.co/cleaningkit
@@DavidMausJr Thanks bro! I will check that out.
I love that you video chat!! That’s awesome!!
It’s fun! Love helping people any chance I get!
Is there a reason you didn’t use ball valve so you can clean out filter without water leaking out?
I should have, its in the kit now but i didnt really think about it since mine are always outside.
@@DavidMausJr Where do you put the ball valve in the order? In between T and Filter?
Hi, How cold does your ice barrell 500 get with the 1/4 hp chiller? And have you tested the 1/2 hp vs the 1/4 hp? I'm looking to get 37 degrees with the 1/4 hp chiller.
It got me to 39 with no problems, I didnt hack mine to get it to 37 but people do. To me, 40 is cold enough :)
I didn't see the drainage spigot linked in the amazon list. Can you kindly link to that?
It comes with the ice barrel 🤙🏽
Can I use this same setup for the plunge pop up tub ?
Have you noticed any other benefits from the Danner pump, versus the Hydrofarm (other than structural integrity)?
Nope. Just stronger and feels like a better quality plastic. Other than that it moves water
@@DavidMausJr Just installed my chiller setup on my 300 today. Followed this exact tutorial, step for step. Works great and saved a ton of space. Thanks again, sir!
Where do you attach the filter? or do you not use one and only rely on the strainer? really love this set up and looking to purchase, just curious on this filter decision. thanks
I show exactly how in the video but the way I have this is directly to the connections into the barrel and then the pump.
I noticed that some other DIY options utilize a whole house filter. in this set-up you only show a very small sediment filter. I have an Ice Barrel 300 and have tried it out w/o any pump/filtration and after a few weeks I noticed the water itself stays clear with hydrogen peroxide and a spa water stabilizer/cleaner BUT there appears to be LOTS of small dead skin flakes floating around, I'm concerned with a small pre-filter it won't be sufficient to keep these all at bay. my goal is to change out water as infrequently as possible. I have purchased the DIY set-up....just wondering if I should add a whole house filter in addition to the small sediment filter you show here before putting it all together
Hi, @davidmausjr, I'm hoping you can answer this question for me. I actually referred a few friends to buy this kit on amazon. I'm not sure what's going on w/ my kit, but since I already had the stock tank and chiller (1/3 Hp Arctic Pod), I thought I could easily adapt. HOWEVER, my chiller which seemed to work fine and could chill my previous tub from high 50's to low 40's in just a few hours (using a 200 Gph pump and 1/2" connections), this new setup takes FOREVER to chill the water. The only thing I can think of is the pump is pushing the water through my chiller too fast and I'm trying to figure out how to slow the flow. Your help/advise would be much appreciated!
Oh man I’m sorry for that. Can u send me a pic or video on Instagram @dmausjr
is chiller waterproof do i need a cover if outdoors??
totally fine outside (ive had all of mine outside and never had one issue)
@davidmausjr thank you for all of your insight. I have procured the IB300. In some of your videos you show a connection to the 1HP AA chiller and in others you talk about going all the way down to a 1/4 HP. I plan to use my IB first thing in the morning so will have the chiller running the night before to get the water temp down. I am debating between the 1/2 HP and 1 HP AA. The setup will be outside in Texas. Thoughts on which one to go with?
With the insulation you’re good with the 1/2hp in my kit. DMJR.co/500diykit
How cold does this chiller get the water ?
Thanks David, great information as always! Hey wondering if there is a way to add a hot water component to this setup to make it a cold/hot setup? Thanks again!
Totally a way to do that!
Any chance you might come out with a video… how to turn any ice plunge into a hot tub? 😃
@@jonmkeller Not a bad idea! :)
@@jonmkellermy wife’s boss has a chiller hooked up to his hot tub built into the pool. It’s not ideal nor cheap though and takes 24 hours to cool. He only uses it once or twice a week because of that. It’s better to have a dedicated unit.
Hi David. Super informative. I have my IB500 but have not bought the chiller yet. Question: what are the specs for a drain hose to connect to the spigot? My chiller is inside so will need to drain using a hose.
Any idea how well that cooler last outside long term? I’m planning on doing this but I’m concerned how long that cooler will last. Maybe need to build a box to put it in to make sure it last as long as possible.
Just set up a similar plunge. But have noticed my filter leaks a bit if I have the chiller and pump unplugged for a day or so. Any idea why?
Probably the water pressure sitting in it. Any reason to keep it off? I just keep mine on
Hi David . I just moved and had to part with my troth I was using. I was wondering if there is an ice barrel you are not in need of or want to part with it. I live in Florida myself. Please let me know and God Bless 🙏🏼😊
Where do you live? Send me a message on IG @dmausjr
Thanks Dave!😊
David do you keep the active aqua outside in the weather, i.e. rain?
How low do the temperatures get with the 1/4 and IB 500 in 80-90 F weather?
How does the 1/4 do with getting it down to the high 30’s?
Same way the bigger ones do, cooling coils
Are the fittings with your DIY relatively universal for other similar tubs with chiller fittings (i.e. redwood outdoors Alaskan cold plunge)? In other words, if I get your DIY package will it be appropriately sized for most other plunges?
Thanks!
Looks like the Redwood Outdoor has a .50 instead of the ice barrel 3/4… do I just update every male- female bard/fitting to .50 or just the barb?
Yes that should work! The only thing you would have to adjust is the attachment to the barrel, i wouldnt suggest getting all 1/2" parts, just get a thread adapter. This will work: amzn.to/3VWD5Jr
Thank you 🤙🏼
I'm confused; doesn't the Active Aqua Water Chiller have a pump inside? If so, an extra pump for extra water flow?
You cooled down the water to 45 degrees in a couple of hours with a 1/4 hp chiller? Is that right?
which pump would you say is quieter? danner or hydrofarm?
Hydro seems quieter, danner is quiet until water flow is restricted which is nice as a reminder to clean the filter.
@@DavidMausJr thanks! ordered the full set up
Just finished the setup today! Used a 1HP chiller from Active Aqua… total overkill haha.
Big question: what smart devices do you use to turn everything on / off? I don’t really want the pump running 24/7 as this sits in a temp controlled garage. Any thoughts? Was thinking a simple timer but. Just don’t want to mess up the active aqua.
Sweet! You can totally use a timer 🤙🏽
The 950 pump still out of stock what another option could be a good option ?
Two questions. How much of the hydrogen peroxide are you adding? And do you have a filter as part of this DIY? Seems like some of your tubs have a 20 micron filter and some do not?
What temperature are you able to maintain with the 1/4 HP chiller in the Ice Barrel 500? Would the 1/2 HP chiller maintain a colder temp?
1/4 is keeping it right at any temp I set it to
39
@@DavidMausJr Thank you very much.
I just did a follow on your Amazon profile. I’m happy to order them through you but if I just going to use my bathtub, can you tell me which items I need? Thank you so much
For sure! You just need a way to keep the hoses inside the water, maybe just using the last connections in a metal material to keep them down? or ziptie them together inside the water
Hey Dave, I have done all the steps and used plumbers tape on everything. I keep having leaks on the bottoms through the rubber washer. Ive tighten it used plummers tape, but it seems to be leaking. Do you have any suggestions on how i can solve this issue?
the full value handle hits the filter any ideas for a pipe between the filter and valve?
I guess I could put it at the barrel connection before the T valve so that the handle is not an issue.
Sorry first timer here. Do some chillers come with filter and pump integrated?
Super helpful thank you. Quick q - if my pump is submersible only (unlike yours which works external to the tub), how would this impact your setup? Ex: if I ended my exterior setup with the filter like yours, would water still flow in & out of the mesh filter?
Do you just keep the pump plugged in and running 24/7?
Yep!