Man sieht im ganzen Video jedoch nicht wo das Laeuferspiel (Spaltmass) eingestellt wird. Ohne das richtige Spiel wird sich der Verdichter bei Erwärmung ( Lastlauf) zerstören.
Starting from 1:42 I recommend to use bearing fitting tools for careful mounting eg. simatec ft33, unless you want to damage the bearing (the most common bearing issues are caused by improper mounting)
Michał Kraus thanks for sharing . I’m using the stick is full copper stick, not metal stick. I choose the Cooper because can protect the bearing surface when install . I know this is not the probability tools. Thanks for your reply I will improve the tools when doing the airend
when need to remove used old bearing must heat the metal . If you no heat the metal too difficult to remove. Puller special tools also can remove the gear and bearing , but will spoil the metal shaft surface. install a new bearing also need to heat the bearing , because you heat the bearing the bearing hole will increase the size. after install the bearing cooling down will going back the original size. Heat will increase the size . Cool will decrease the size. different size bearing different timing and tempeture.
I can be considered in the 25μm to 50μm High Pressure discharge clearance, to 100μm to 150μm, low pressure suction clearance for AIRREND ELGI, please tell me about these clearance. I have a problem with a compressor because it was necessary to change the bearings because these don't work and the screws suffered many scratches. Please support if the clearances gives are a good option to improve the vibrations in our device.
It's not a good reparation.. You sould use paper gasket with the according thickness to maintain the compresion chamber measure, if you use joint paste you are changing the total length and will be problems.. Take care
When high compressor oil temperature have this few reason , maybe the radiator cooler dirty ? Fan belt condition not good ? Or Compressor oil thermostat problem etc ....
very interesting for me as a non-pro that is interested in mechanical devices. thanks for sharing!
Great 👍👍👍👍
this is such a wonderful video and there are so few takers for it . thank u sir ji , lovely information sharing
Amazing
airman 👍
Nice jobs
very good work by experienced technician thanks
Sreejith Ts Thanks for watching and support
Man sieht im ganzen Video jedoch nicht wo das Laeuferspiel (Spaltmass) eingestellt wird. Ohne das richtige Spiel wird sich der Verdichter bei Erwärmung ( Lastlauf) zerstören.
Starting from 1:42 I recommend to use bearing fitting tools for careful mounting eg. simatec ft33, unless you want to damage the bearing (the most common bearing issues are caused by improper mounting)
Michał Kraus thanks for sharing . I’m using the stick is full copper stick, not metal stick. I choose the Cooper because can protect the bearing surface when install . I know this is not the probability tools. Thanks for your reply I will improve the tools when doing the airend
Very good
Very nice..!!!!!!!
Thank for you good job
thanks
good job
There is one hole fitted with alenkey bolt what is the uses of that hole please can you tel me sir?
bom trabalho obrigado por nos mostrar seu trabalho bem feito isso que vc jateia ai no parafusso como chama onde podemos comprar
Bom dia. Acredito que seja lixa d'água.
Hi sir, wanna ask about how u dismantle the cylindrical roller bearing?
What is the machine you use for the bearings at 2:12? It heats up the bearing?
SKF Brand bearing heater
May I know where can I learn how to service and overhaul air compressor in Malaysia?
Why heating bearings and gears when assembling and at what temperature? what is the name of heating equipment? please pardon me for asking
when need to remove used old bearing must heat the metal . If you no heat the metal too difficult to remove. Puller special tools also can remove the gear and bearing , but will spoil the metal shaft surface.
install a new bearing also need to heat the bearing , because you heat the bearing the bearing hole will increase the size. after install the bearing cooling down will going back the original size.
Heat will increase the size . Cool will decrease the size.
different size bearing different timing and tempeture.
Thank you
I can be considered in the 25μm to 50μm High Pressure discharge clearance, to 100μm to 150μm, low pressure suction clearance for AIRREND ELGI, please tell me about these clearance. I have a problem with a compressor because it was necessary to change the bearings because these don't work and the screws suffered many scratches. Please support if the clearances gives are a good option to improve the vibrations in our device.
it must be 0.009 "
good video. where can I find a manual about repairing airend??
Marbi25 what model AIREND you want to overhaul?
Pls vedio normal.
Atlas 1200-330 airend overhoul mannual provid me.
You put too much high temp silicon gasket, I suggest to use loctite 518
Thanks For Comments. Now we Using Loctitle gum already red color ..
It's not a good reparation.. You sould use paper gasket with the according thickness to maintain the compresion chamber measure, if you use joint paste you are changing the total length and will be problems.. Take care
Mamame Laverga thanks your sharing🤝
porque o vídeo não esta na velocidade normal afinal amigo você queria mostrar o que ?
Hi. Any possibility I can learn how to overhaul an air end through your program?
Michael Jay Pernes I will try my best when I overhaul the AIREND and taking the video thanks for support
Kalau ngatasi masalah temperatur tinggi/ oli gak mau naik bagaimana mas...
Refan Afandi sniper merk apa bos? bs di bantu email od13ok@gmail.com 😅
When high compressor oil temperature have this few reason , maybe the radiator cooler dirty ? Fan belt condition not good ? Or Compressor oil thermostat problem etc ....
Sleeping now
Kalau overhoul kompresor denyo 390 bisa gak bos?
Mesin saya posisi di Semarang.
Thanks
You want overhaul AIREND or engine this Denyo 390
Comproser model 390s kalau untuk minyak apa yang perlu di isi di dalam gear itu
Shell Corena oil Rs32
Mobil Rarus 424
Faircol RA32
Total Fluidmatic IIIG Automatic Transmission Fluid
@@TEDDYKASHIMURA ads sample gambar bos
catalog.total.sg/en-sg/products/9t0/FLUIDMATIC-IIIG
@@TEDDYKASHIMURA untuk rotary gear...berapa liter perlu di isi?
Elgi.450/150.repreng.bareng.number.dala
The first of NU* inner bearing too hight temperature.
Lu Van Com I follow Japan original bearing parts. Next time I try using another bearing... thanks for recommended
iyi calısma
Bisu tidak ada petunjuk teknis pemasangan bearing
USELESS ... kill that music and say something instead !!!!!!!!!!!!!!!!!