Это видео недоступно.
Сожалеем об этом.
How to repair screw compressor
HTML-код
- Опубликовано: 14 мар 2021
- #screw_compressor #compressor #screw
In this video we will look at how to repair leaking screw compressor.
If you like this video please click the like button and let this video reach others.
Please also visit and subscribe to my other channel ruclips.net/channel/UCBwprn-1E1Cf1knx5rsNMJQ for car reviews.
Good job. That was nice to watch
hi i think you may have not fitted the check ball in the seal housing this will cause oil leaks
Great video thank you! What type of sealer did you use?
Good job
Thanks!
Доброго дня! Блок CF 90 або 60. По перше так губки сальника не могло видавити, це тільки при монтажі!!!
По друге не помітив резинової кульки в кришці сальника!? Вона впливає на працездатність сальника! Гарного дня!
Selam, contaların altına sürdüğünüz nedir.
To make the gasket holes, you can use a metal ball fron a bearing, to cut it, is easy
wonderful advice!! thank you very much
የት ነው የማገኘው ተበላሽቶብኝ ነበር compreser termo cuple or senser
Sper part?
Sooo good
Your sealer only dries in the absence of air, no need for it to setup like with a silicone..
Very hot encreas after assembly, pressure make,
How I can reduse it
thermostatic valve oil filter or temperature sensor
maganda, ang lakas....
Thank you very much!!
oil is every where , we have the same problem in our factory how do we get to you ? any address
Thanks dear
You are most Welcome dear!
Now I watched the video until the end. First of all, you should use professional tools and not screw like an amateur. I know this type of compressor. Is an original from Germany from MAN-GHH.
If the radial shaft seal is changed, the sleeve ring must also be changed. Otherwise the compressor will be leaking again after a very short time.
No paper seal is required for the surface seal. Applying Loctite 574 to the clean surface with a foam roller is the best seal. In the absence of air, the sealant sets and seals optimally.
Indeed! well Said!
I have a rotary screw compressor the problem i have is the screw pomp makes noisy scream I don't know what is the problem oil and filters are changed any help pls ?
Dear! the number one cause of a noisy screw compressor is worn out bearings!! Please check to see if the compressor bearings are in good condition!! Good luck!!
@@TheAbJGarage thanks you so much hope nothing more !
Sir we have same screw compressor but i very try to extract bearing by hammer but no possible
You need a bearing puller to do it... We are performing all type of screw compressors service and located in coimbatore, Tamilnadu, India.. Contact us for more support
If still the bearing refuses to come off with a puller, try heating with low heat. That will allow the bearing to relax and release it's firm grip as it tries to expand a little .
@@TheAbJGarage no, if you heat the bearing, heat from bearing's inner racer will immediately pass to the shaft which inturn will expand the shaft along with the bearing.. So unfortunately you can't remove the bearing from the shaft
@@CLASHOFCLAN-tx3km that is sure to happen if you heat it for long. I was suggesting heating the bearing and quickly removing of the shaft.. we have used this method on some hard to remove bearings and it worked just fine ....look at this video dear...ruclips.net/video/2du522NFpLY/видео.html
@@TheAbJGarage that's great but this is a motor bearing, where I hope it is a ball bearing and the fit will be less compared to other bearings like tappered roller or 4 point angular contact ball bearings.. Moreover this bearing looks large enough to hammer and pull it out... This will not work in our cases where there will be no place to hammer the bearings
My screw compressor is trip again and again
Dear check to see if the pump runs free by spinning the drive pulley by hand, if it is free, then look for electrical problem (probably short circuit) at the motor or its control wiring. If the compressor is not free to spin manually, then it's probably internal problem causing resistance, such as damaged bearings due to lack of lubrication, or foreign materials jammed in the system causing resistance to rotation.
Oil tamp problem and not for oil cooling...