I will never understand why you have any dislikes. You are amazing to your attention to detail and the extra work in your projects. Keep the camouflage, it makes it rugged. Maybe do a Raptor camouflage? Excellent work!
Hey great job with the spring over axle swap! Looks good! Not sure what the horsepower is or how soft those springs are but you might want to look into adding an anti wrap bar. Flipping the springs to the top can exaggerate spring wrap, turning your springs into an “S”. I’d say run it first and then decide.
Grateful to see another video of the Suzuki project. Yeah, it was much more work than anticipated. Holy moly. Great work though, as always. ... I m a bit worried of the rear suspension (at the extremes), but I do not see it going too far. It is stiff.
I have a couple of those tamron lenses. They are very good especially the 28-75, you can capture a good wide angle shot with it. Your Zuk build is looking mighty fine. Keep it up.
We have a lot of those Suzuki's here in the Philippines Same 3 cly 600cc but there called Rusco here. I never seen any with short shackles. There all 8" Most have fiberglass canopies behind the cab here with short jump seats on both sides of the bed. I have yet to see that on any in the states. I just purchased mine a week ago and will making a bumper for the front to install a winch and roof rack. We do a lot of off road ridding since there are no roads going to our property in the mountains. Were limited as to what we can take on the bike so the Rusco is a welcome edition. Keep up the great work!
Finally! A video showing the correct way to lift a mini truck. Don't buy a kit that just puts all of your geometry out of acceptable operating range. Everything will just wear faster and the vehicle will handle worse.
I think it looks great! Only thing I kept thinking is when is he going to round the corners off on those rear shackles...well I guess never! lol. Great video! Thumbs up as always! 👍
Oh yeah I forgot to tell you I bought a slip yoke eliminator for a 88 samurai then called advanced adapters and emailed them what I needed to connect my mini transfer case to the yoke eliminator and it's not much of a difference but they nailed it and I was in to it for a fuzz over $300 for both then went to the junk yard and made my own super duper driveshaft
Excellent work, but one question.. why did you bother powder coating those spacers if you were going to leave that cross-member all crusty? Or is that for another video?
With all the tools you have I don’t understand why you’re working on the ground get your saws off the ground get your drill press off the ground you’ll save your back and your knees 😎
Are you in a heavy snow zone? I’m wondering how much snow can you get thru with your plow setup? Is the truck heavy enough or have enough power to bust through big snow.
The rear shackles can not rotate due to the side mount tab of the rear bar. this will really hurt your articulation. If you half round the ends of the shackles and the rear bar mount tabs the problem is fixed,
MEASURE TWICE CUT ONCE HOMIE COME ON MAN....! Nah I'm just kidding I have a 92 Mitsubishi minicab which is a dirty clone to a high jet or Suzuki carry I did the same lift basically what you've done and yeah I made mistakes but oh well it's a cool little hobby these trucks are neat and I love it
Man you got to take advantage of your lift, I put it up on the lift eye level and use the tranny Jack to hold the pumpkin up, saves your knees when you're 60 😉
You have my vote for You Tube Channel of the Year. 💪👍👊
Turned out nice 👍
Thanks for taking the time to document all your work for us! Take care Austin 🙂
Thanks for watching!!
I will never understand why you have any dislikes. You are amazing to your attention to detail and the extra work in your projects. Keep the camouflage, it makes it rugged. Maybe do a Raptor camouflage?
Excellent work!
This channel is like a gold mine for me. Thanks a lot!
Austin
thats the coolest snow plow I have ever seen!!!!! nice job Again !!!!!!
Looks alot better and I bet it rides and handles alot better doing those things to it as well. Keep up the great work Austin!
Hey great job with the spring over axle swap! Looks good! Not sure what the horsepower is or how soft those springs are but you might want to look into adding an anti wrap bar. Flipping the springs to the top can exaggerate spring wrap, turning your springs into an “S”. I’d say run it first and then decide.
This Suzuki is really coming together bro
I’m shocked to see you move away from the Napa Black on the spring hangers. 🤣
That was a lot of work you put into that lift. 👍🏻
Grateful to see another video of the Suzuki project.
Yeah, it was much more work than anticipated.
Holy moly. Great work though, as always.
...
I m a bit worried of the rear suspension (at the extremes),
but I do not see it going too far. It is stiff.
I have a couple of those tamron lenses. They are very good especially the 28-75, you can capture a good wide angle shot with it.
Your Zuk build is looking mighty fine. Keep it up.
Thanks!!
Great job , you can make driveshaft spacer out off pinion flange it will be about 1/4 inch or 3/8 inch that will help
We have a lot of those Suzuki's here in the Philippines Same 3 cly 600cc but there called Rusco here. I never seen any with short shackles. There all 8" Most have fiberglass canopies behind the cab here with short jump seats on both sides of the bed. I have yet to see that on any in the states. I just purchased mine a week ago and will making a bumper for the front to install a winch and roof rack. We do a lot of off road ridding since there are no roads going to our property in the mountains. Were limited as to what we can take on the bike so the Rusco is a welcome edition. Keep up the great work!
100% Nuts On!! Turning into some awesome content. 🔥🔥🔥
Perfect timing! i get to watch this before getting ready for work.
Skills bro! This looks great, and the work is top notch!
Always amazed by your projects. Little truck looks great. Love your channel
nice job correcting yourself. Was just about to comment about driveline angle. I like your solution. considering this lift for my S110 hijet.
Loads of fun...looking forward to seeing what's next...😎👍
I love your attention to details on your builds. You need some black lug nuts now to go with the blacked out rims.
Excellent job once again. Thanks for Sharing.
I put. LED headlights on mine for plowing. You will also want a LED light bar mounted high….for when plow is up. Keep up the good work!
I got some ideas about lights!! Thanks!!
Super cool series!
You did a brilliant job with that machine! 👍
awesome builds love them videos keep them coming sir .👍👍👍👍👍👍👍
Great work!
Finally! A video showing the correct way to lift a mini truck. Don't buy a kit that just puts all of your geometry out of acceptable operating range. Everything will just wear faster and the vehicle will handle worse.
It looks great. Nice work…..!
Really great video,you show your talent every time you fabricate a new item.keep doing what your doing and carry on.😎😎😎👍👍👍
You’re the best bro!
Honestly I'd rather the CARRY over the red truck , this little rig is wicked,
nice job .....you should make k kits ......master of your craft ....
Austin, you need to build a stand for your drill press. you could incorporate storage in the base for bits.
I think it looks great! Only thing I kept thinking is when is he going to round the corners off on those rear shackles...well I guess never! lol. Great video! Thumbs up as always! 👍
You need a belt grinder 2" x 48" or 2 x 72" . Its one my used tools in my machine shop..
Hello. Nice job. I think you should add some light on the top of the cabin, since after wearing the plow, standard lights are covered greatly.
Oh yeah I forgot to tell you I bought a slip yoke eliminator for a 88 samurai then called advanced adapters and emailed them what I needed to connect my mini transfer case to the yoke eliminator and it's not much of a difference but they nailed it and I was in to it for a fuzz over $300 for both then went to the junk yard and made my own super duper driveshaft
Excellent work, but one question.. why did you bother powder coating those spacers if you were going to leave that cross-member all crusty? Or is that for another video?
New to the channel, great stuff here. And thumbs up on the Tameron lens.
2 things…it needs wider tires and wheels and it will level out when you add some weight in the back to get traction when plowing
Perfect 👏👏👏
With all the tools you have I don’t understand why you’re working on the ground get your saws off the ground get your drill press off the ground you’ll save your back and your knees 😎
You might want to look into driveline spacers for a samurai, might be same pattern?
Are you in a heavy snow zone? I’m wondering how much snow can you get thru with your plow setup? Is the truck heavy enough or have enough power to bust through big snow.
Chains and or sand bags for the rear while plowing?!
What lens did you use before?
I have the same Tamron lens and its great, wish it had stabilisation built in.
Just a Sony kit lens! So far I like the tamron!
New lens seems good
Great Job! ... Are you building this to eventually Sell and move onto the next build when's it's complete?
I’ll probably keep this one around!
ive been watching the snow pile up and been like you can now test ur plow rig!! i live not far from you lol
We still only have 2” maybe!!
Hey Austin! I saw you got a new camera lens. I have a Tamron lens for my Nikon film camera. What camera are you using for videos?
THANKS, Rich
I use a sony a7ii for now!
@@austinniemela Thank You Sir!
The rear shackles can not rotate due to the side mount tab of the rear bar. this will really hurt your articulation.
If you half round the ends of the shackles and the rear bar mount tabs the problem is fixed,
Good job. Go on. And also what have You decided to do with body? Are You going to repare it?
One of these days ima come back and hes gunna have 1mil subs
AUSTIN CANDY RED THE MINI TO MATCH THE BIG BOY TRUCK ... THAT WILL BE RADD .
So when is the Honda K series awd swap on the Suzuki Carry?
Great video as always, I was wondering we see a 20 min video, how many days of work are we seeing condensed to 20 min?
The rear took 3 days, short days however!
Awesome
Does it plow snow decent?
This thing is badass!! Are you going to keep the camo or eventually paint the body too??
Thanks!! I haven’t decided on paint yet!
Sweet
If you ever need to sell this Kei it should be perfect for any Hokkaido millionaire...just to help you find the right buyer.
About time to swap in a 4 cyl. In it. Coming along nicely..👍🏽👍🏽
You did all that work to just end up back were you began
Now some camouflage Raptor liner
Nice work, what camera are using?
Check the description
It’s a Sony a7ii
Finally
Lookin' killer. man! When time come you should put the Sedona RipSaw R/T on this bad boy. Those tires are the bee's knees!
MEASURE TWICE CUT ONCE HOMIE COME ON MAN....! Nah I'm just kidding I have a 92 Mitsubishi minicab which is a dirty clone to a high jet or Suzuki carry I did the same lift basically what you've done and yeah I made mistakes but oh well it's a cool little hobby these trucks are neat and I love it
Turbo it !
Build a bigger powder coating oven!!
Man you got to take advantage of your lift, I put it up on the lift eye level and use the tranny Jack to hold the pumpkin up, saves your knees when you're 60 😉
He explained in the prior video that he tried to use lift and it the rear lift arms are too long for the Mini Truck
From western Sahara
Wow! Really nice idol! Shoutout! #MOVEONTV
Don't need no stinkin' mufflers....except maybe for inspection.
😳👍
👍👍👍👌🤝😎
Next week Toyota.
Me like
20:26 ... definitely worse