370Z H&R 20mm F&R Wheel Spacers - This is How You Fix The OEM 19" Rays Hideous Wheel Fitment 😃😎🔥
HTML-код
- Опубликовано: 22 фев 2022
- Adding H&R Front/Rear spacers to get rid of the OEM wheel gap. These are 20mm and hub centric, these are high quality and H&R doesn't disappoint. This definitely fixed the wheel gap and now it is more on point, looks sporty just the way it should have looked from the factory. Thanks for watching, trying to upload once a week and become a more consistent content creator for the G and Z platform. See you at the next, take care and have a good one everyone.
Where I purchased the F&R wheel spacers:
throtl.com/products/hr-drm-wh...
where I purchased the black wheel lug nuts:
conceptzperformance.com/czp-s...
Music Credit:
tubebackr-fresh-up: Fresh Up by tubebackr | / tubebackr Music promoted by www.free-stock-music.com Attribution-NoDerivs 3.0 Unported (CC BY-ND 3.0) creativecommons.org/licenses/...
Cherry Metal by Arthur Vyncke | / arthurvost
Music promoted by www.free-stock-music.com
Creative Commons Attribution-ShareAlike 3.0 Unported
creativecommons.org/licenses/...
Trap Sport Gaming Music | PLAY THIS GAME by Alex-Productions | / @alexproductionsnocopy...
Music promoted by www.free-stock-music.com
Creative Commons Attribution 3.0 Unported License
creativecommons.org/licenses/...
#memosgarageaz #Nissan370Z #370z #H&R #H&Rwheelspacers #ISR #nissanznation #nissanzlife #Z34 #throttlebodyspacers #vqlife #vqfamily #vqnation #vq37vhr #infiniti #infinitig37 #infinitig37sedan #isrperformance #conceptzperformance #g37enginemods #g37sedanmods #g37sedantuned #admintuning #adminremotetuning #g37exhaust #g37sedan #mancavegarage #garage #garagegoals #garagelife #garages #garageshop #garagemade #garageworld #garagebuild #garagework #wheels #infinitiparts #infiniti_street #g37sohoexhaust #dragracing #dragrace #torquesolution #enkierpf1 #cworksdesign #g37sohoexhaust #g37resonatedtestpipes #g37paddleshifters #bccoilovers #bcg37coilovers #mishimotooilcatchcan #pedalcommander #race #cptcoldairintake #hotchkisswaybars #agencypowerpulleys #z1motorsports #isrlongtubeheaders #ecutek #g37ecutek #g37racingfuel #carbonfiberairducts 
Авто/Мото
on stock nismo suspension can u run a 20mm without rub bc i don’t have my finders rolled or anything
Have you looked online to see what the height differences is between a 370z touring vs a mismo model? All I could find was the Nismo is about .6" lower but not 100% sure. Also are the Nismo wheels the same spec as the 19" Rays F&R? As well as tires? In my case with the 19" Rays 19x9 (front), 19x10 (rear), Tire Size: 245/40/19 (front), 275/35/19 (rear), Wheel Offset: +47 (front), +30 (rear) and 20mm spacers all around, If I was to lower the car about .5-.6" I think I wouldn't rub at the front for sure, the rears might be close though. Installing BC Racing Coilovers soon, so we'll see how that goes.
Hello! Any thoughts on 30MM in the rear? I ordered that size then saw this video. I’m on stock suspension base with 18” wheels. I need to close that gap as much as possible until I get aftermarket wheels.
Hello, sorry for the late response, have crazy holiday stuff going on right now 😀😁. I guess it all depends on what your wheel width, offset and tire size is. Below is my wheel and tire info:
"Wheel Size: 19x9 (front), 19x10 (rear)
Wheel Offset: F: +47 (+27 with 20mm spacers), R: +30 (+10 with 20mm spacers)
Tire Size: 245/40/19 (front), 275/35/19 (rear)"
With the 20mm spacers it still looks like going 25mm I would have been okay. If I would have gone 30mm I think once I lowered the Z I probably would have rubbed unless I got new tires and stretched them. Not sure if that helps, thanks for watching 😀.
What fluid did you spray on to clean the surface?
Looks like I used some type of brake cleaner, but I should have used some kind of rust removing fluid, degreaser or at minimum dish wash soap diluted with water.
How have the front wheels and spacers been? Do you need to tourqe them down again, and again after miles of driving??
They've been great. I did go back and re-torque them about 60 miles later and only found about 2 of the nuts were a little bit loose. I'm going to check them all again at the next oil change.
@@MemosGarageAZ Yeah, 2 of mine got loose after 5 miles
My oil change is coming up soon so we'll see how they check out.
Drive it about 50-100miles and re torque it and when u do an oil change re so it again and repeat .
I have a 2015 qx50 it also has stock 19s how would I judge spacer size would 20m work the same for me ? I’ll be dropping them on springs until the day I don’t have to use spacers and can get a better setup
You'll have to do some research and find out what's a perfect fitment 19" wheel offset (same tire size as your current set-up if possible) for your car. Once you have that you'll also need to find out what your current wheel offset is and with all the info you should be able to figure out what size spacers you would need. Hope that helps, good luck.
@@MemosGarageAZ okay that’s good to know will look into what spacers would give me a nice flush look ! as later down the line I would like to get rid of the spacer for a better wheel spec , if I wanted a more aggressive setup does my offset need to be + or - ?
🔥🔥🔥🔥🔥🔥🔥🔥
Thank you brotha 😃🙏
Have you had any wobble after like 60mph?
No man, thankfully I don't. You may have to go back in there and clean the surfaces better. I'm assuming the wobble started after you installed the spacers?
@@MemosGarageAZ thanks for the quick response bro. Yeah I didn’t notice it before the spacers but tbh Idk how much I was paying attention. I just took them all off and cleaned it. We’ll see if it helps. It’s possible I’ve got other suspension issues already from different owner -.-
Yeah man no problem, good luck.
@@kuzyordaddy927 make sure you clean it good its flush and torque to right spec . I changed mine and went straight to the highway went over 100mph kinda stupid of me doing that but no wobbles , as long u do it right
@@kuzyordaddy927 it doesnt sound like the spacer is the problem , it could be ur suspension, control arms, ball joints i would check those just in case
What’s the link to the lug nuts?
conceptzperformance.com/czp-shank-mag-type-lug-nuts-for-oem-wheels-nissan-370z-infiniti-g35-g37-q40-q50-q60-45812_p_35557.php
Don't forget to choose the black finish from the drop-down
Nice bro , wud the spacer add more rotational weight to the wheels
Maybe a little bit, but not enough to notice a difference
@@MemosGarageAZ thanks bro
NP 😃
@@MemosGarageAZ Hey bro hru? Just a quick question, when time for oil change do you have to take out the oil cooler as well to remove all of the old oil as well .
Nah, most of it will drain out and a little bit may stay behind and mix in with the new oil, but It's such a low amount that it's never been an issue for me and it shouldn't be for anyone else.
That nut thing, how did you fill the gap?
Hello, sorry I'm not quite understanding what you're asking, could you please clarify? Thanks
@@MemosGarageAZ nvm it's okay I just put anti-seize around it so it doesnt rust when i put the wheel on
@@sxnchez34 Oh I see now LOL. That's not a bad idea
did you notice tramline and bump steer difference on normal street driving when you added the 20mm spacers?
Hello there, honestly haven't felt any difference in steering at all in any way.
@@MemosGarageAZ ok good to know. Can the stock suspension be lowered a little or is it fixed?
@@r.k862 It's fixed, if you want adjustability then you'll have to go with Coilovers I'll be doing coilovers in the next couple of weeks on the Z so stay tuned for that.
Nice video love my z
They're fun little cars for sure 😀
You went 20mm rear? Why do some pictures of 25mm rear look equally as flush
Yes I went 20mm in the rear, I wanted to start there just in n case I was going through rub when I lower the car which I haven't done yet. Once I do and I feel there's room I'll go 25mm, Ai also went 20mm at the front but I really should have gone 25mm instead.
@@MemosGarageAZ I see.. would you say the rears are still slightly sunken/more sunken than the fronts in person?
No, the fronts are sunken in than the rears, this is why I was saying I should have gone 25mm at the fronts.
@@MemosGarageAZ alright thanks
No problem