I connected, i connected, after that i conected,after that i conected, after that i conected, after that i conected, after that i conected. Dude, explain why have you connected, explain the circuit, how the current flows, what the ic does, etc. We are learning here, not copy pasting blindly.
Hi, I built this circuit board and the red led stays on all the time, the pot makes the relay click off like it supposed to. What could be wrong? I know its probably something I have wrong. Thanks for a great video.
Rudimentary - Ok, using the 100uF / 10K + 4K7 as a time constant for the Mark-Space ratio to sustain and spread out switch points. Figure the traditional Schmitt trigger better option not governed by RC only with threshold of feedback.
@@KiyanisLab thanks for your efforts, you should make a kit that can charge both li-ion and lead-acid battery with overcharge and discharge protection. this will be huge. what you say
I want the circuit to be active on 14 volts and disconnect the load on 13 volts. Can this same circuit be used or do i need to make any changes. Please help. I am trying to use this in my car. When the car turns on and the alternator turns on, the voltage is around 14 V.
Nice circuit design but am just wondering how it works since pin 1 is the output of the IC an a diode is connected in reverse direction to the bc547 transistor that triggers the relay for cutoff will the circuit work i take out the zener diode connected to pin 1 of the IC an connect a 1k resistor to pin 1 an to the base of the transistor
hi there... this circuit looks very promising. I have a 12v gel battery. Need to have to cut off voltage of 12.5v. should I change the value of the zener diod? thanks
Need to redesign circuit for battery charging in such a way that if voltage goes above 13.8 or if voltage drops below 10.6v then output should not be able to reach 12v battery under charging. Power should be from Ac transformer say 0-12v and then given to circuit to charge battery.
Hi i would like to know can i use this circuit to charge a output 12v backup smaller battery from a 12v input battery. The supply charging battery would be a Car battery and the smaller battery is the alarm battery. So it would be 12v to 12v i hope this makes sense.
Don't waste your time and money building this circuit. Rather go with a 555 timer. With this circuit the relay will open and close repeatedly when using it will a battery. Batteries drop in voltage when connected to a load and recovers when there's no load. Let's say you set your cutoff voltage to be 9.5V, when your battery hits 9.5v the relay will be triggered, as soon as that happens the battery voltage will increase above the cutoff voltage and there will be a load on your battery again causing the relay to be triggered again, this cycle with repeat itself. Using a power supply, like he did in the video, you will not notice this because a power supply has a stable voltage.
Pls make this circuit for inverter in which it can provide 12v battery power backward to the inverter circuit when there is no mains power supply Pls reply can you make it?
Hello sir. How can we incorporate this into an sg3524 powered inverter? Also can you kindly provide a circuit that I can incorporate into the said inverter for cutoff charging when battery is full?
Some improvement is urgently needed... Let us assume it cuts output at 10v. As soon as the load gets off, voltage shoots again, load gets connected gain... This process repeats again and again
Hello brother I need a help can you guide me in building a circuit for car where the voltage cut off should work once the battery voltage falls below 13v....the load through the circuit is approx. 5A
It does not work, because when the circuit is switched on and off the load, the voltage in the battery rises again and the circuit is switched off and the load reconnects.
Brother mere pas power wheels Jeep hai Jo 6v battery se chalti hai lekin Mai usme lithium battery lagana chahta hu par vo 11.1 volt ki hai to mujhe ye battery usme lagane ke liye kitne watt ka step down converter lagana hoga Kya ye sahi rahega ya aap koi sujhav dijiye please please answer me
@@madansharma7597 thanks brother but 7806 ic jyada load nahi le sakta ye heat hokar jal jata hai mene use Kiya tha lekin 2 pices 555 dc motors ka load nahi le pa rahi hai heat hokar jal jata hai
I connected, i connected, after that i conected,after that i conected, after that i conected, after that i conected, after that i conected. Dude, explain why have you connected, explain the circuit, how the current flows, what the ic does, etc. We are learning here, not copy pasting blindly.
Perfect demonstration with circuit plus point
Instablaster
Hi, I built this circuit board and the red led stays on all the time, the pot makes the relay click off like it supposed to. What could be wrong? I know its probably something I have wrong. Thanks for a great video.
Mashallah very good information
The world's best teacher
Rudimentary - Ok, using the 100uF / 10K + 4K7 as a time constant for the Mark-Space ratio to sustain and spread out switch points. Figure the traditional Schmitt trigger better option not governed by RC only with threshold of feedback.
will it protect the battery from overcharge, as you mention that this is for over-discharge, but I need overcharge protection?
coming soon bro
@@KiyanisLab thanks for your efforts, you should make a kit that can charge both li-ion and lead-acid battery with overcharge and discharge protection. this will be huge. what you say
thank for diagram
I want the circuit to be active on 14 volts and disconnect the load on 13 volts. Can this same circuit be used or do i need to make any changes. Please help.
I am trying to use this in my car. When the car turns on and the alternator turns on, the voltage is around 14 V.
આભાર
Nice circuit design but am just wondering how it works since pin 1 is the output of the IC an a diode is connected in reverse direction to the bc547 transistor that triggers the relay for cutoff will the circuit work i take out the zener diode connected to pin 1 of the IC an connect a 1k resistor to pin 1 an to the base of the transistor
hi there... this circuit looks very promising. I have a 12v gel battery. Need to have to cut off voltage of 12.5v. should I change the value of the zener diod? thanks
no it can be adjusted with trimpot
I loved your drawing good men
Thank you my friend!
trima kasih atas vidionya
👍👌
This circuit can use 12 v battery and 12v 1500w inverter?
yes it can
Ahmed Raza
Electrical 2nd year
Roll number 08 ❤
Possible Auto Cut Off Charging & Battery Drain Limit Cut Off ?
Its can use motercycle ?
Hello sir, can this circuit work for a 24v battery bank?If not what are the components I need to change for 24v battery..Thank you in advance
I love this
Need to redesign circuit for battery charging in such a way that if voltage goes above 13.8 or if voltage drops below 10.6v then output should not be able to reach 12v battery under charging. Power should be from Ac transformer say 0-12v and then given to circuit to charge battery.
Hi i would like to know can i use this circuit to charge a output 12v backup smaller battery from a 12v input battery. The supply charging battery would be a Car battery and the smaller battery is the alarm battery. So it would be 12v to 12v i hope this makes sense.
Any alternative of LM393 Ic plz.. tell me
Can you develop this handle12v 200Amp battery pack????
Cool 😎👍👌👏❤️😍
Don't waste your time and money building this circuit.
Rather go with a 555 timer. With this circuit the relay will open and close repeatedly when using it will a battery.
Batteries drop in voltage when connected to a load and recovers when there's no load. Let's say you set your cutoff voltage to be 9.5V, when your battery hits 9.5v the relay will be triggered, as soon as that happens the battery voltage will increase above the cutoff voltage and there will be a load on your battery again causing the relay to be triggered again, this cycle with repeat itself. Using a power supply, like he did in the video, you will not notice this because a power supply has a stable voltage.
hello. may you please answer my question? how much i can drain current in the output? what is the output current limitation?
Can i get this ckt from you? Pl.. Price...
Is they a node on pin 8 of the IC an the positive rail of the circuit
Pls make this circuit for inverter in which it can provide 12v battery power backward to the inverter circuit when there is no mains power supply
Pls reply can you make it?
Circuit runs max current when battery volty is low keeping battery draining
my led doesnt switch off and the voltage doesnt change from the initial 12v, does anyone know what the reason could be?
1st check connections then the ic
The 6 volt battery can be charged on this circuit ????
Hey, is this circuit like a12 volt smart charger? Thanks for any info.
Yes, it is
The circuit does not have hysteresis, the battery will rise up once the load is disconnected so the circuit will try to come back on again.
Exactly, no much difference between cutoff and turn on voltage
Hello, does anyone know the name of the program that was used to design the circuit?
Hi Sir, Can i add this over discharge protection To lithium Battery 18650 Charing, Please advice.
yes with little changes
WOW GOOD PROJECT....
capacitor is missing in components list
Bhaiya ye circuit kitne ampare ki battery le sakta hai aur kya charge karte samay ham circuit ke input per power supply de sakte hain please bataye
You hide last connected jumper.
so funny man....
Bro can use this circuit for 12v 5amp battery
Yes you can
Hi your videos r helpful for me ,can u explain the BMS Please I need BMS
From what did you supply power to the circuit?
Hello sir. How can we incorporate this into an sg3524 powered inverter?
Also can you kindly provide a circuit that I can incorporate into the said inverter for cutoff charging when battery is full?
Good
Some improvement is urgently needed... Let us assume it cuts output at 10v. As soon as the load gets off, voltage shoots again, load gets connected gain... This process repeats again and again
Sir also hint on a 48v battery as you are treating that of 24v battery.Thank you
Which software is used for circuit making??
hello...how much Ah battery can charge with this module?
it is for discharge protection for charge protection ruclips.net/video/8yfpuk05LrQ/видео.html
Hello brother I need a help can you guide me in building a circuit for car where the voltage cut off should work once the battery voltage falls below 13v....the load through the circuit is approx. 5A
I mean the load should get activated only when the engine starts I.e 13+V and deactivates the load when engine is off I.e below 13v eg.12.9V n so
no schematic, no working principle ?
you ripping off someone's else circuit ?
piss poor
Brother Jo aapne apni video me 12v automatic charging circuit banaya hai Kya vo lithium ion battery pack par bhi sahi Kam karta hai please answer me
It does not work, because when the circuit is switched on and off the load, the voltage in the battery rises again and the circuit is switched off and the load reconnects.
how to connect 35A battery ..??
Please make bms projection board for 18650 battery
Circuit not working your voltage does not goes down and up.
Hello sir touch light banao jo ki ek bar touch karne se Jale aur dusri bar touch karne se band Ho jaaye please sar banaa dijiye diagram bhi please
Brother mere pas power wheels Jeep hai Jo 6v battery se chalti hai lekin Mai usme lithium battery lagana chahta hu par vo 11.1 volt ki hai to mujhe ye battery usme lagane ke liye kitne watt ka step down converter lagana hoga Kya ye sahi rahega ya aap koi sujhav dijiye please please answer me
आपको 11 वोल्ट बैटरी से 6 वोल्ट डीसी चाहिए7806 का सर्किट बनाकर लगाइए इनपुट 11 वोल्ट आउटपुट 6 वोल्ट मिलेंगे आपका काम हो जाएगा
@@madansharma7597 thanks brother but 7806 ic jyada load nahi le sakta ye heat hokar jal jata hai mene use Kiya tha lekin 2 pices 555 dc motors ka load nahi le pa rahi hai heat hokar jal jata hai
kitni motors hain ?
@@faridi-bin-Zouq Bhai jaan 4 motors hai modal no.555 dc motors
Hello, how are you? This is the program for installing electronic parts
why don't you explain its working mechanism?
Please kindly send the 24volt low battery autocut system
Plz make 18v battery charger auto cut off
its more important to explain how i works, not construction!!!
Where is the AC input on the diagram?
Brother 4000watt UPS transformer ka bobbin size kya hota hy
1000$
How to make 6 volt Betty charger
Please sir video Hindi to Urdu nodemcu board 8 channel relay WiFi nodemcu board
ok bro
alguien me explica como funciona por que no entiendo la explicacion
1A ?
Halp.. mee Friends
12 volt 20 amp auto cut circuit kaise banaye🙏👷
Sir your nombar send mee🔜🙏📞
Sir nombar send
Fake video voltage ghatane se cut karta hai badhane se nahin karta
Halp 📞📞
wasting my time
Fake video
how can you say bro it is working well please make it test it