How to do Maintenance on Bravo 3 Prop
HTML-код
- Опубликовано: 4 сен 2024
- This video will show you how to Remove and Install Props, on a Mercruiser Bravo III
For full transcription visit onboardwitheddi...
2000 Johnson 90Hp Water Temperature Gauge Installation. on a 2001 Sea Fox 172 Center Consul. Part from ebay item # 332256421187
/ onboardwitheddie
/ onboardwitheddie
/ onboard_with_eddie
When available, we use affiliate links and may earn a commission
Links to products in Amazon
MERCRUISER PARTS
Hinge Pin Tool Compatible with Mercruiser Mercury Alpha 1 Gen 2 Bravo I II & III Outdrive Sterndrive amzn.to/3uD0CUl
VOWAGH Bellow Retainer Ring Install Driver Tool Compatible with Mercruiser Alpha One Gen Two Bravo Replace Mercruiser 91-818162 Sierra 18-9870
amzn.to/47YaaHF
Gimbal Bearing Puller/Remover & Bearing Installer & Alignment Tool fit for Mercruiser Alpha Alpha 1 MR Bravo OMC and Volvo
amzn.to/3sVuZVp
Manifold Engine Block Drain Plug Kit Replaces Sierra 18-4226 for Mercruiser 22-806608a02 Compatible with GLM 13992 Pack of 5
amzn.to/3QVUT3o
Fuel Filter and Filtering Disk Set 35-8M0093688 866171A1 8M0093688 35-892665 for Mercury Marine Mercruiser Engines with Gen III 3 Fuel Cooler
amzn.to/47Xlhka
V8 Distributor Cap and Rotor kit for Mercruiser and Volvo Penta 5.0, 5.7, 6.2 Engines, 350 MAG MPI 5.0 5.7 GXI GI
amzn.to/3t1uBop
863631T1 Water Distribution Housing Assy Distributor with Drain Plug for Mercury for Mercruiser for Quicksilver
amzn.to/3NdCRZx
RPS-GLM Bell Housing Gimbal Water Hose Tool, Driver Insert kit for Mercruiser Bravo Drives Replaces 91-43579 &
amzn.to/4aaxRhV
RPS MERCRUISER Water Pump Rebuild KIT Impeller Cover O-Ring 496 8.2L 5.7 5.0 4.3 350
amzn.to/3uMyPRz
Bearing Retainer Install and Remove Tool for Bravo III Replaces 91-8053741 805374-1 Bearing Retainer Wrench
amzn.to/3TbY1e3
BOAT MOTOR
Quicksilver 802859Q1 2-4-C Marine Grease with Teflon, Multi-Purpose Marine Lubricant - 8 oz. Tube
amzn.to/3N5QXvS
Slippery Pete - Lower Unit Gear Oil Pump for Standard Quart Bottles, Includes 3/8 inch Metal Swivel, 8mm and 10mm Adapters
amzn.to/3sXh2GA
Ultra1Plus™ SAE 25W-40 Premium 4-Stroke Synthetic Blend Marine NMMA FC-W | 2 Gallon (8 Quarts)
amzn.to/3T3IzRt
STAR BRITE Star Tron Enzyme Fuel Treatment - Concentrated Formula 32 Fl. Oz. - Treats up to 512 Gallons - Fuel Stabilizer & Treatment, Gasoline Stabilizer, Star Tron Marine Enzyme Fuel Treatment
amzn.to/3sOZo82
STA-BIL 360 Marine Ethanol Treatment & Fuel Stabilizer - Full Fuel System Cleaner - Fuel Injector Cleaner - Removes Water- Protects Fuel System -
amzn.to/3t1KKdq
STAR BRITE Star Tron Enzyme Fuel Treatment SEF Gasoline Formula
amzn.to/3uEgN3Q
MISCELANEOUS BOAT RELATED PRODUCTS
YXGOOD Heavy Duty Snap Fastener Tool, 1PCS Adjustable Snap Pliers, Fastener Pliers Tool
amzn.to/4a1bhrU
3M TALC Marine Adhesive Sealant Fast Cure 5200 (06535) Permanent Bonding and Sealing for Boats and RVs Above and Below the Waterline Waterproof Repair, White, 1 fl oz Tube
amzn.to/3sT5ynB
Martyr CMR Rudder/Trim Tab Anodes
amzn.to/3uJIacu
Collinite 885 Fleetwax Paste
amzn.to/3R0xJsE
US Marine Products Aluminum Anode Kit Fits OMC BRP Johnson Evinrude
amzn.to/3RoGXjT
Bonbo 91-805457T1 Nut Socket Wrench Tool Fits for Mercruiser Bravo 3 Prop Propeller Prop
amzn.to/46GmLOJ
Marine Products LLC Aluminum Anode Kit for Johnson and Evinrude 90-225 HP 1991 and Later Includes Hardware Replaces OMC
amzn.to/46QwBxv
LucaSng 2 PCS Marine Magnetic Outdrive Gear Case Drain Plug, Screw with Gasket Replace 22-8M0058389
amzn.to/3R9Yj2z
SCP Maintenance Service Kit With Spark Plugs and Fuel Filter For Kohler Marine Generator Models
amzn.to/3sVmLwN
Thank you so much for putting all of that together. I just bought a boat with a Bravo 3 and I'm just seeing what I may be up against for future maintenance. You're a good thorough teacher. I appreciate your effort to teach while you repair. Some guys know how to repair but they don't know how to teach. You can do both very well so thank you.
Awesome videos Eddie. We appreciate you taking the time to show us the proper maintenance of boats and all they entail
Eddie, Great videos. You did say something like you heard propellers do not need to be lined up, but, you line up the part numbers. You were honest in your representation and I would have done the same on my boat. I spoke to a propeller repair shop today and he says the two propellers on a Bravo III spin at different RPMs and you do not need to line them up.
Hi Eddie... Awesome job and a great step by step outline of the work being done along with a with clear view and well articulated narration to boot !!! I am new to boating and have this exact same drive (Bravo III) and I like doing as much maintenance myself on my vehicles as I can so this is a perfect watch and learn video clip for me personally as well. Thanks so much for taking the time to shoot it ! SRIII.
Happy to help you out. And Thank you for your support🤙⚓️
Nice work Eddie, you explained it very clearly while showing us what to do. Thank you.
Hey Eddie
Thanks so much for your videos!
I’ve been watching you from way back. You have me the confidence to winterize my boat myself. Truly appreciate it pal.
As a fellow Long Islander....
Thank you!!!!!
Thank you Mike. And thank you for your support. Have a happy holiday.
Really enjoying your video series. My '03 Cobalt 220 has the Bravo 3 and these videos are just the thing! Thanks!
This is why I like dry racking my boat. Saves the corrosion on the drives
Been using your videos to learn/teach myself maintenance with my Sea Ray 240 Sundancer. Good stuff.
Glad to help out. thank you for your support. Be safe
Awesome How To Videos, Great Instructions, Really Appreciate Them.
Thank you. And thanks for your support
You gotta clock or time the duoprops. Tail edge of leading prop must immediately flow into leading edge of trailing prop blade
Thanks Eddie!! I've always jammed the 2x4 between the props, farting around for a minute. Never thought to have the 2x4 between the prop and cavitation plate..LOL SMH Been a subscriber for a while now....welcome back
this time the camera was impeccable, love your video. it s all good from Montreal.
michel desrosiers thank you 🤙
Using a carbon steel brush on stainless can induce rusting. Thanks for the video!
Thank you - very informative. Excellent , clear instruction!
Thank you. And Thank you for your support
Nice video
Thank you for your support. Hope it helped you out.🤙⚓️
Thank you Eddie. Was very informative.
Those are nuts vs. bolts. Thanks for the video.
Thank for the correction. I know.But I wasn’t going to reshoot the whole video,over. For the Correction of nuts the bolts. I figured everybody would get it. 🤙
Eddie love your videos, do you have a video for the brovo 3 propeller shaft seals replacement?
Yes, would be very helpful as that's not a Bravo 3 video. In the process of doing mine--would be a life saver!
Love your videos. Thanks so much.
Thank you For your support
brilliant tutorial
Great insightful video, thanks brotha
You’re very welcome. Thank you for your support. and watching the videos.
@@OnboardWithEddie I have a 06 Larson Cabrio 240 with a Volvo Penta outdrive.... That large Socket toll would be the same size (universal) or what cha think, appreciate it....
Great video, thank you
Hello Eddie, I have a Bravo III outdrive and I'd like to know if there is an impeller in it? I already change the impeller on the motor beneath the cool fuel module/alternator. BTW, you are so thorough with the videos, great job and thank you!!
I read about clocking the props fwd prop blade at 12 and aft at 6 🤷🏻♂️
Great video
I have twin 5.0s and B3s and appreciate these videos, thanks.
Have you made a video that shows greasing the engine coupler?
Very informative glad i watched.
Great video. Thanks for the helpful tips and tricks.
Hey love your videos, I am very grateful for them. I am leaking gear oil at the props. what should I be looking for ?
Prop Shaft Seals are going out/worn. A lot of tools and procedures, but doable. You need to remove the Bearing Carrier and shaft out to replace them. Hope Eddie will do a video on it...
If you want to clean the props, submerge them in vinegar overnight or a day or two. No scrubbing required in my freshwater experience.
Thanks for the video - I noticed you put grease on the larger props threads, but not the smaller one. Is that something you did on purpose?
Eddie, if i want to replace my Bravo One can I change it to a Bravo Three or would I need to change the entire mount on both sides of the transom?
Great video! What’s the acid wash you mentioned? Muriatic? If so, I’m curious how it works. Did you have to mix with water? Did you put in a spray bottle? Did you use gloves, goggles & face mask?
Do you recommend put racing oil in the engine. I have heard that it is much better than using the standard.
Eddie, thanks for the awesome videos. Can you tell me if you are using Quicksilver 2C4C or marine grease? Thank you.
Hello Eddie, please could you know how we can remove just the water pump poulie, target it just to change the seal ??
Hello Great videos Do you know where the where the Mercathode Anode Assembly in located on a bravo 3 Mine is all bottom painted and it may be covered Thank you
this was filmed a few years ago so Im not sure if you will see this - I need to take mine off this weekend and Im a little unclear as to what you "lined up" when you put the props back on - was it the inscription matching up on both props ? Also another guy I watched used different size wrenches (except for the second prop, that was the same) - he used 13MM for anod and 37mm for first prop - I would think bravo III would all be the same idk ?
Curious, have you thought about installing drive showers on your BIII's? I just installed them on my BIII X's as a precautionary measure.
Drive Showers?
I'm having problem removing the front prop, what can I do to remove it?
Trying hitting it with a hammer and a block of wood. As low as you can on the blade as low as you can to the hub of the prop. Don’t you just hit one side, keep spinning the prop and hit each blade. (Low by the hub of the prop and blade) 🤙⚓️
what do you use to acid wash the props?
What is the purpose of the nose cone? My B3 doesn't have one
To keep the electrolysis from eating away at your props and out drive. I would recommend putting one on. 🤙⚓️
Hi Eddie. I have a question, since I am not a mechanic by trade but I like to do basic maintenance on my boat ( i will get a new one in a few months) and I wonder if the special double-size wrench at each end would be a good option. rather than the 2 deep sockets you use to remove the propellers? I already bought my torque wrench. thank you
If you use a wrench. You will not be able Your torque wrench. to put it back on. And I don’t think you can take the first bolt off with a wrench. You would be able to get in there. Hope that help you
@@OnboardWithEddie thank you for taking the time to answer me, it's a special key made for the bravo 3 but ok if I buy the two sockets as you have,it's better to buy another ratchet just to unscrew or i can take my torque wrench to unscrew the screws (LEXIVON click torque wrench with 1/2" drive up to 25/250ft-lb)
on this special wrench there is at each end a 1/2 in. square hole to enter the 1/2 in. torque wrench
Ohhh!!! nice! I’ve never seen that. But it sounds like it’ll work good for me. 🤙⚓️
hello friend I want to change the oil to my outdrive mercury bravo 3 double propeller I wanted to know how much I should buy and if necessary when I make the change fill the plastic tank that is in the engine. Thank you very much in advance
Hey Yoyany. It’s about 2 1/2 quarts so get three. But Follow this link. it will show you how to do it. ruclips.net/video/OuJUFqpGdaI/видео.html
@@OnboardWithEddie thanks you so much
Your welcome. Thank you.for your support.
The specs say 60 on the rear and 100 on the front.
Thank you for pointing that out. I just watched a video at the beginning I said 100 on the rear and 60 on the front. and doing a video when I was doing it. I also said 100 and rear 60 on the front
Where did you hear me say it? The other way? I will correct it. Thanks
@@OnboardWithEddie I think I got confused with the terminology. I should have said forward facing prop (big nut) 100 and aft prop (small nut) 60. I think that is also what you were saying. Thanks.
Is your boat moored in salt water? If so, is it in the water full time?
My boat is docked. And I take it out of the water in the Winter.
what did you use to clean the props
OSCAR RODRIGUEZ on & off hull & bottom cleaner.
U said at the start of the video that front prop os 60 pounds. And when u torque it you showed us the torque wrench at 100.
The Inner prop is at 100 and the outer prop. is at 60. I only showed how munch on the inner prop. Not the outer prop.
Why does it matter how the props go back on? Won’t they spin in the same way regardless...?
yes. merc says it dont matter. at a given point they line up anyway.
Jimbo sammy Actually I figured it out. When mounting them back on, the rear propeller should have one blade that points up (12 o clock) and the outer propeller should have one blade that points down (6 o clock).
That way they are properly synced, making sure that they will never both be pointing up, ever. It’s to avoid cavitation on the props.
Mercruiser reference 72221
rinkerboats.vanillacommunities.com/discussion/861/prop-timing-torques-specs
So do not match up the way they were put on before, it isn’t necessarily correct.
How old are your Bravo 3's? There appears to be zero corrosion.
mark dimaio They are 12years old. I do paint them every year.
how can I tell if I have a spun prop on a Bravo III?
no rubber hubs on bravos. cant spin but may shear splines though unlikely.
if you have slippage it could be engine coupler. would smell burnt rubber likely.
or sheared splines in coupler and that would be audible.
Where have you been eddie
Tyler Anderson. I had To raise my son. Lol
@@OnboardWithEddie I fully understand. Hopefully you'll put out some more boating videos. I learned alot from your channel Best wishes to you and yours
The way I did mine was much easier, hit an underwater log and ripped the whole drive off, got a little transom damage doing it that way, but very effective.
Derek Walter. hey Derek. thank you, For your input. But I think, I’ll Stick to my way. Lol 🤙
100ft lbs on both nuts was told 90lbs. Could have saved me $100cnd on the other hand I didn't get dirty
Wow, click bait