Thank you for this video! Didn’t even realize this was a new feature. - i realize, if you want a make a specific route. Instead of selecting a destination far away. Just make a short destination via a specific track, then make another short destination for another track so on and so forth until you reach the end.
No problem 😃 glad you enjoyed watching it. You certainly can, you pretty much have the freedom to go anywhere around the route which is another reason we love this feature 🙂
This is a nice feature, thanks for the video 🙂 Just a hint: for smoother control when approaching rail cars with Vectron (or with similar locos) the train drivers usually first apply a bit of loco brake (about 0.5 or 1 ATM of brake pressure) and then apply minimum power to start moving, because as you can see there is too much power already on smallest setting on the light engine (with no rail cars). The loco brake also makes sure you will not bounce so much from the bumpers. Another hint with the loco brake is that when you were waiting on the red Stop/Danger signal you could apply full loco brake and then release the train brake which would slowly release the rail cars while waiting. As you've seen, releasing the train brake when you were cleared to go took lot of time (this depends on the length of the train), but with loco brake it would be instantly released and you could go.
I purchased the minimum paid version of tsw5 a few weeks back. Do I have to wait until the ECML section is released on TSW5 or can I download it through another way?
Nice video, thanks for sharing, I like it, especially the part between minute 06:39 and minute 07:10 where you crash and bump into the train carriage several times in a row, I had a good laugh 😄😂 And wait a minute, if this game were "realistic", there should be a Game Over screen at minute 07:11, because you've been hit by the incoming train. But keep up the good work 👍
I am getting TSW4 for Christmas, and by then the Blackpool Route will be out. I would like to be able to Spawn a Pacer on the Tees Valley line, as they were introduced there when the route is set
I have been trying to spawn trains onto time table mode and then set a path to travel. but my trains will not move and will not connect (*class 37 EPX & Scotsman) Any help or advice will be much appreciated
Well apon release of TSW 4 you can still spawn trains into timetable mode on all routes so our guess is it is looking likely to be a permanent feature.
This video was an absolute delight to watch 😂❤, especially the part when the vectron had to be coupled to the flatbeds 😂😂. Absolutely loved this video throughout. +1 sub for this channel 🎉
Thank you for this video! Didn’t even realize this was a new feature.
- i realize, if you want a make a specific route. Instead of selecting a destination far away. Just make a short destination via a specific track, then make another short destination for another track so on and so forth until you reach the end.
No problem 😃 glad you enjoyed watching it. You certainly can, you pretty much have the freedom to go anywhere around the route which is another reason we love this feature 🙂
Brilliant all round...great video of a cool feature...the possibilities are endless!
This is a nice feature, thanks for the video 🙂
Just a hint: for smoother control when approaching rail cars with Vectron (or with similar locos) the train drivers usually first apply a bit of loco brake (about 0.5 or 1 ATM of brake pressure) and then apply minimum power to start moving, because as you can see there is too much power already on smallest setting on the light engine (with no rail cars). The loco brake also makes sure you will not bounce so much from the bumpers.
Another hint with the loco brake is that when you were waiting on the red Stop/Danger signal you could apply full loco brake and then release the train brake which would slowly release the rail cars while waiting. As you've seen, releasing the train brake when you were cleared to go took lot of time (this depends on the length of the train), but with loco brake it would be instantly released and you could go.
The GBRf vectron looks amazing!
Certainly does its on the Creators Club and called "GBRF Fictional" by Tanzafox
simens vectron is from czechia
@@Mamradsellzze Its from germany
my bad, your right@@amisvolvo945but we use it in czechia
I purchased the minimum paid version of tsw5 a few weeks back. Do I have to wait until the ECML section is released on TSW5 or can I download it through another way?
Nice video, thanks for sharing, I like it, especially the part between minute 06:39 and minute 07:10 where you crash and bump into the train carriage several times in a row, I had a good laugh 😄😂
And wait a minute, if this game were "realistic", there should be a Game Over screen at minute 07:11, because you've been hit by the incoming train. But keep up the good work 👍
are you aware of the keybinds to spawn trains in timetable mode for console? xbox specifically?
Hello there :) yes it should be left on the D pad to open the spawning menu
gotcha, thanks!
I am getting TSW4 for Christmas, and by then the Blackpool Route will be out. I would like to be able to Spawn a Pacer on the Tees Valley line, as they were introduced there when the route is set
What about on console can u spawn trains in on timetable mode
Should be able to. I believe it's left on the D pad or something like that
How do u get different routes? I’m stuck with the training centre?
If you set a path in time table will it stay there to play again at a later date or will you have to reset again
I have been trying to spawn trains onto time table mode and then set a path to travel. but my trains will not move and will not connect (*class 37 EPX & Scotsman)
Any help or advice will be much appreciated
Will they change this or let it remain?
Well apon release of TSW 4 you can still spawn trains into timetable mode on all routes so our guess is it is looking likely to be a permanent feature.
its just a feature of the game
What but on xbox one to select where to go on routemap
This video was an absolute delight to watch 😂❤, especially the part when the vectron had to be coupled to the flatbeds 😂😂. Absolutely loved this video throughout. +1 sub for this channel 🎉
Ps: I love that horn too 😂❤ its fun
@@GamesRTech Thankyou so much for the sub!! im glad you enjoyed the video Yes it was a challenge i must admit to couple it up haha
Does PS4 work too?
Should do. If you press left on the D pad it should bring up the Spawn menu
Is it possible to let ai take over your spawned train en then take you to your selected place?
AI cannot take over your spawned train no its only user controlled.
How would you spawn one on ps4? Im desperate for an answer (if anyone knows how to spawn the flying scotsman please note)
@@Scotland4evr not sure as we use PC but I'm guessing it will probably be the D pad on the controller as that's what it is for xbox.
It wont works...i already press Tab button but i cant spawn any train
Wont work now
What the hell how did you did that?🤯
How do you tell the game where you want to go once you spwaned a train in?
Bring up the map view. Click on the train and then press select path and then path it to where you want to go
How do you bring up the map on ps4
Can you set an ai to drive
I have a question how do u become trains I’m new and don’t know it
is it possible to turn the hud and driver assist of? so you only drive by the signals you see out your window?
Yeah you press F1 and it hides everything. Not sure what it is on consoles though
@@britishlocomotivestudios4372 but are the signals and signs along the route, detailed enough to follow?
Get scotsman