I am a mechanical engineer I can sharpen a driil bit by hand no special tools or angles. Just a bench grinder. Perfect every time. I've never bought a driil bit for about 30 years. Just a flick of the wrist for a couple of seconds done
*EXACTAMUNDO!* goldsmith / master jeweler been doing same way with bench grinder, sharpening stone and used electrical grinder too without angle tools. all by hand and eye coordination
Buy a Drill Doctor & it takes about 60 seconds & you can choose 118⁰ or 135⁰ angle, & you can split the tip, plus it sharpens carbide drill bits, too. Works better than hand grinding by far.
This is one of the most dangerous things you can do to a cutting stone. You will form a groove on the side of the cutting blade is the same as scoring a breaking point in it. This is extremely dangerous.
I have noticed that the grinder will not always be in the same position each time it is set up and the drill bits will not always hit the same place in the wheel. However, the point is moot if you are skilled enough to notice when a wheel has an issue. The fact is, anything you do in a shop is dangerous and the trick is to be aware of the worst case scenario. and mitigate (like not grinding every drill bit on the same point of the wheel). And if every new experience or idea causes you to cringe instead of refining the idea and thinking ahead, maybe a workshop is not a place you should be in because those are the people who get hurt.
@@josephfroman7135 you should use a gringing stone not a cut off disk are you trying to get people hurt !!! If that cut off y broke at that speed it goes flying fast use the right grinding disk for the right job as well as oil is better than water for cooling the drill bit after sharpening...
OMG. This guy made a simple 30 second sharpen into a major job. Just hold the bit at the right angle on the bench grinder and rotate the bit at the same angle for both sides. Then grind a bit off the back side behind the edge. So simple
I have watched numerous videos on drill shappening but this is on point especially the 120 degrees angle vertical and horizontal is awesome. I have shappened some bits without this precision. Welldone
Read the comments. Have you noticed how many people can talk a good job? With my 59 years as a skilled tradesman I have no criticism, just gratitude for a good idea.
I would fix a bracket with a screw to the grinder handle thread and fix it to the vice. Squashing the case in a vice will deform the plastic potentially pinching moving parts.
Grinding a drill on a cutting wheel is the biggest nonsense I've ever seen. This weakens the side of the cutting disc until it blows up in your face!!! Drills are sharpened on normal grinding wheels.
Для начала. Это видео для самоучек. Сверло такого диаметра как правило так не используют. Сначала делают точку керном и сверлят малым сверлом 3 или 4 мм. Потом расширяют отверстие сверлом нужного размера. При заточке сверла режущую кромку направляют навстречу вращения наждака.(диска). Также можно делать малые отверстия зенкером.
Anyone that uses a grinder with a cutoff wheel to cut wood has no business trying to show anyone how to sharpen a drill bit! I'm not familiar with the brand of the grinder but makita is not a good quality tool brand so I guess that shows the intelligence level of the maker of this video!
Yeah I know what you mean, been using a Mikita skill saw for 30 years it has been putting food on the table for all those years. There’s no American made tools anymore parts made in china and assembled in US
Seriously. The right tool for the right job. Metal cutting blade not for wood. Step off. I am disappointed in the lack of experience. Do something the wrong way for 50 years, you're still doing it wrong. Period.
I learned how to do this by eye as a tradesman. And this is a great way to do it without that skill. Some drill bits are only tip hardened. So it pays to learn how to re harden old drill bits too. But some think it is not 'cost effective' these days. But I can tell you that I have saved tens of thousands of dollars not buying new drill bits. And I have working drill bits that are over 50 years old that belonged to my father. Waste not, want not. Signed: The ultimate recycler.
Wonderful - a man of my own heart 20 when I started 84 now and the world's greatest hoarder. Saved me a fortune over the years especially with almost all projects/repairs I set up to save money. Again, well said
Oh, it’s for marking the sharpened and unsharpened positions, helping to make the grinding work more even! Thank you for watching the video! I love you
Good video. The only negative thing I can see is that a cutoff disc was used, where it should have been a regular grinding disc. The cutoff disc is not made to have pressure applied to the side like that. But I also understand that it wasn't a lot of pressure. Someone else may not be able to be as careful as you were. ;-)
The end result is a far cry from perfect - at best only sligthly better than at first. The center part is the problem. Should be narrower, thus facilitating the centering of the drill and the drilling itself. Don't give advise like that when you don't know much about it!
Didn't amaze me. My steady wrist can sharpen bits for ferrous non ferrous with equal lip within a few minutes. You cannot drill in such thin sections without predrilling. Or cut the web to perform it
He's going about it the hard way I used to sharpen them at work after the grinder it and I learned how to how to sharpen them with angle this guy is going about it the hard way
Who cuts wood with an angle grinder and a hacksaw……..I bought a hacksaw blade once and after a few strokes all the teeth were gone.I took it back to the shop and the lady said it’s probably made for cutting wood.
Para afilar una broca no hace falta hacer ningún artilugio , se puede afilar a pulso con un poco de habilidad , esa broca del vídeo no parecía cortar muy bien.
How about not dulling your tooling in the first place. RPM= 3.82x constant surface feet per minute, divided by tool diameter. You spindle speed is so high the cutter is just rubbing.
I use a bench grinder and I can have it just a sharp, and take half the time without having to make a jig, Americans have been using bench grinders to sharpen their drill bits for years.
It is very, very dangerous to grind with a cutting disc. Change the cutting disc to a grinding disc and make the video over again ...then it is cool. The way it is now with a cutting disk is hazardous.
Never do what he just did please. Angle grinders are one of the most dangerous tools due to the disc breaking and trying to make it into a grinder weakens the disc increasing the chance of it breaking and launching into you. Also, their not meant to cut wood. Always use a tool for what it’s meant for or you will get the trouble your asking for. Also, without cutting oil on the drill bit, you are going to heat up the metal your attempting to drill resulting in dulling the drill again. Just buy a grinding wheel and stop listening to online know nothings please. Safety first or stay home.
My old boss was a machinist in Germany before coming to the US he could sharpen drill bits holding them to a bench grinder…I can’t…and I remember him every time I can’t drill thru something 🫤
Absolutely atrocious way to use an angle grinder and cut off disk. You can absolutely explode a disk using it to grind with the side, as well as using it to cut wood. Bush league and dangerous. Do not do this.
Long winded, if you use drill bits a lot, experience and practice against bench grinder you will learn automatically correct angle to sharpen drill bit
Fraid to say put that effort alongside a brand new drill and you'll see that grind was a total disaster . LOL seems to be some conflict of interest .......... cool the drill while grinding but achieving the opposite with the cigarette lighter . Cant figure that one
The lighter was used to soot the area of interest. "If soot gone, then the area is 'treated'." Other than that, what this video shows is a total lack of understanding of which tool to use for what job. First off, you dont use an angle grinder to cut wood. Next up is, you dont use a cutting blade for a grinding job. Then after that, you dont need two separate 120° angles but you need to make sure your grinder is properly angled. As you can see, the maker of this video doent care at all when it comes to feedback.
So ein Quatsch, diesen ganzen Krempel braucht kein Mensch, von einem Mechaniker einfach zeigen lassen wie man Bohrer schleift und dann hat man es mit etwas Übung bald raus. Idealerweise benutzt man einen Schleifständer, bevor man beim einspannen in einen Schraubstock auch noch seinen Winkelschleifer schrottet.
That was sharp? The way it was cutting, I would be considering throwing the bit away AFTER he "sharpened" it. Nobody has time for that. Well, maybe this guy. I mean he had an insane amount of time available to make the worst jog on the net...so there's that.
Gracias x tu invento es genial bueno para los que tengas transportador, una tuerca soldada con otra para checar el ángulo correcto y el que te haya adivinado cuantos grados debe de tener el triángulo de madera x que nunca dijiste a cuantos grados trazaste el corte con el trasportador!!!! Pero de todas maneras gracias genial yo prefiero gastar en una broca nueva pero cada quien su pedo!!!!
Lol... You don't know anything about sharpening drills. You don't leave the tip of the drill like that (like a shovel), with a mega positive attack angle. To reduce drilling resistance, make two undercuts. Respect the tool.
Why would you take tips off of someone who uses an angle grinder to burn through a piece of wood? Do you not have a saw? What next? Putting in screws with a hammer? 🫣
![CHILE vs. BRASIL [1-2] | RESUMEN | ELIMINATORIAS SUDAMERICANAS | FECHA 9](http://i.ytimg.com/vi/5ObJt_71AYc/mqdefault.jpg)
I am a mechanical engineer I can sharpen a driil bit by hand no special tools or angles. Just a bench grinder. Perfect every time. I've never bought a driil bit for about 30 years. Just a flick of the wrist for a couple of seconds done
That's so great! You are an excellent and skilled worker. I would love to hear about your experiences. I think it will help me a lot! Thank you
@@InventorSCa 😊
*EXACTAMUNDO!* goldsmith / master jeweler been doing same way with bench grinder, sharpening stone and used electrical grinder too without angle tools. all by hand and eye coordination
So am I, but I don't go on line telling everyone. What an eejit. 👽
@@InventorSCgood for you but not for me....
Buy a Drill Doctor & it takes about 60 seconds & you can choose 118⁰ or 135⁰ angle, & you can split the tip, plus it sharpens carbide drill bits, too. Works better than hand grinding by far.
Those are great ideas, thank you so much. Wishing you joy and happiness with your loved ones on the weekend
You should used cutting fluid or water mixed with soluble oil to keep the drill bit cool. Then it should last longer
It and worked great. Thank you for sharing this great video. Hope you have other great tips to share. Cheers
Glad it helped! Thanks for watching and leaving your comments! Have a nice day!
This is one of the most dangerous things you can do to a cutting stone. You will form a groove on the side of the cutting blade is the same as scoring a breaking point in it. This is extremely dangerous.
Always be careful with your actions for your own safety. Wishing you a happy weekend
I have noticed that the grinder will not always be in the same position each time it is set up and the drill bits will not always hit the same place in the wheel. However, the point is moot if you are skilled enough to notice when a wheel has an issue. The fact is, anything you do in a shop is dangerous and the trick is to be aware of the worst case scenario. and mitigate (like not grinding every drill bit on the same point of the wheel). And if every new experience or idea causes you to cringe instead of refining the idea and thinking ahead, maybe a workshop is not a place you should be in because those are the people who get hurt.
@@josephfroman7135 you should use a gringing stone not a cut off disk are you trying to get people hurt !!! If that cut off y broke at that speed it goes flying fast use the right grinding disk for the right job as well as oil is better than water for cooling the drill bit after sharpening...
Great tips, and even better video making and demonstration skills!
Glad you liked it! Have a nice day!
Interesting method. I bought a Drill Doctor and it works great every time. This is much cheaper, though
Thank you for sharing your great idea. Wish you always success and happiness
OMG. This guy made a simple 30 second sharpen into a major job. Just hold the bit at the right angle on the bench grinder and rotate the bit at the same angle for both sides. Then grind a bit off the back side behind the edge. So simple
Oh that's great, thank you for watching the video and sharing your good ideas. Wishing you a new week full of energy
@@InventorSC been a machinist for over 25years. That’s just how I do it. A lot easier
I have watched numerous videos on drill shappening but this is on point especially the 120 degrees angle vertical and horizontal is awesome. I have shappened some bits without this precision. Welldone
Thank you for watching the video and always supporting the channel. Wishing you good luck and happiness in life!
Een goede video om te demonstreren hoe het niet gedaan moet worden. Zeer gevaarlijke opstelling.
Thanks for watching!
Read the comments. Have you noticed how many people can talk a good job? With my 59 years as a skilled tradesman I have no criticism, just gratitude for a good idea.
I am 62 and I feel it, I struggle day by day so do it when you can you never know what tomorrow brings.
I'm glad to see your comment. I always wish you lots of health and happiness in life. Thank you very much
i like it 2< this is how i make things, some precision tools but also human labor involved, great tut>
Thank you for always supporting me. Wishing you always happiness and good luck in life. I love you!
I would fix a bracket with a screw to the grinder handle thread and fix it to the vice. Squashing the case in a vice will deform the plastic potentially pinching moving parts.
Please secure the grinder securely to ensure safety when doing so. Wishing you a happy weekend with your loved ones
You should make a vidio on how to split the point. Drills start much faster and don't walk with a split point.
Thank you
Easy to set up using what you have to hand, this is what we in the UK call DIY !! Genius 👍🏻
Glad to hear that! Thanks for sharing your feedbacks! Thanks for watching! Have a nice day!
I would saw wood with a dead skunks jaw, or any other flipped out thing, just to read equally weird comments.
Nice explanation, thanks.
Glad it was helpful! Thanks for leaving your comments! Wish you all the best!
Grinding a drill on a cutting wheel is the biggest nonsense I've ever seen. This weakens the side of the cutting disc until it blows up in your face!!! Drills are sharpened on normal grinding wheels.
Thanks for watching!
In wieviel Grad hast du das Stück Holz geschnitten
Oh, it’s 60 degree angle. Thanks for watching! Have a nice day!
Для начала. Это видео для самоучек. Сверло такого диаметра как правило так не используют. Сначала делают точку керном и сверлят малым сверлом 3 или 4 мм. Потом расширяют отверстие сверлом нужного размера. При заточке сверла режущую кромку направляют навстречу вращения наждака.(диска). Также можно делать малые отверстия зенкером.
Thanks for watching and sharing your experience! Wish you all the best!
❤❤❤ee❤❤❤❤❤❤❤❤❤w us us and I am a new phone eee rffff_
Anyone that uses a grinder with a cutoff wheel to cut wood has no business trying to show anyone how to sharpen a drill bit! I'm not familiar with the brand of the grinder but makita is not a good quality tool brand so I guess that shows the intelligence level of the maker of this video!
Thanks for watching!
A GOOD tradesman can use non standard tools to do many jobs. I just used to pick anything that was safe and handy to save time. It's called skill!
Yeah I know what you mean, been using a Mikita skill saw for 30 years it has been putting food on the table for all those years. There’s no American made tools anymore parts made in china and assembled in US
Seriously. The right tool for the right job. Metal cutting blade not for wood. Step off. I am disappointed in the lack of experience. Do something the wrong way for 50 years, you're still doing it wrong. Period.
It's called inexperience... @@aleccrombie7923
Gostei do vídeo
Glad you liked it! Thanks for watching the video!
I learned how to do this by eye as a tradesman. And this is a great way to do it without that skill.
Some drill bits are only tip hardened. So it pays to learn how to re harden old drill bits too. But some think it is not 'cost effective' these days. But I can tell you that I have saved tens of thousands of dollars not buying new drill bits. And I have working drill bits that are over 50 years old that belonged to my father. Waste not, want not.
Signed: The ultimate recycler.
That's awesome, I like your way of thinking! Wish you happy in life. I love you
Wonderful - a man of my own heart 20 when I started 84 now and the world's greatest hoarder. Saved me a fortune over the years especially with almost all projects/repairs I set up to save money. Again, well said
Çok güzel bir uç keskinleme tekniği, çok beğendim.TR.
Thank you, your advice is great. Wish you always happy and happy
Only the cutting edge should be sharpened...then each side must tapered off evenly.
Thank you for sharing this wonderful thing! We always look forward to receiving your support. Wishing you always be happy with your loved ones
Since you already had a cut-off tool at the ready, it might have been a lot easier/faster to use it to make the channel in the wood than the hack saw.
Take advantage of everything you can, thank you for watching the video
👏👏👏👏👏👏👍
Thanks for visiting the channel!
Saludos inventor porqué se tiene que calentar con encendedor antes de afilar ?
Oh, it’s for marking the sharpened and unsharpened positions, helping to make the grinding work more even! Thank you for watching the video! I love you
Yo creo q. Para que no tenga frío la broca!!!
Good video. The only negative thing I can see is that a cutoff disc was used, where it should have been a regular grinding disc. The cutoff disc is not made to have pressure applied to the side like that. But I also understand that it wasn't a lot of pressure. Someone else may not be able to be as careful as you were. ;-)
Hello! Thank you for sharing useful information with everyone! Wish you all the best!
88656😅ĵ
👍
The end result is a far cry from perfect - at best only sligthly better than at first. The center part is the problem. Should be narrower, thus facilitating the centering of the drill and the drilling itself. Don't give advise like that when you don't know much about it!
Thanks for watching!
Okay, so anyone that cuts wood with an angle grinder is someone that has no clue whatsoever what they're doing.
Thank you for watching the video. Hope you have a nice weekend
I can sharpen them by hand. I'm a old school machinist though.
Thanks for visiting the channel and sharing your great experience! Wish you all the best!
What’s with the gloves?
Thanks for watching!
Not supposed to grind on the side of the wheel, it could explode, extremely risky move
Thank you for watching the video and commenting, it's great for us. Wishing you a happy weekend
Rubbish.
Didn't amaze me. My steady wrist can sharpen bits for ferrous non ferrous with equal lip within a few minutes. You cannot drill in such thin sections without predrilling. Or cut the web to perform it
Thanks for watching and sharing your experience! Wish you all the best!
That's so great. I don't know if they really worked when I did the same as you did
Please do it, I think great things will come to you
😊😊😊😊😊😊😊😊😊😊
If I domy job like that😅😅😅😅😅
boss（XXX）me100%😁😁😄😄
just grind a toolbit
He's going about it the hard way I used to sharpen them at work after the grinder it and I learned how to how to sharpen them with angle this guy is going about it the hard way
Thanks for watching!
Who cuts wood with an angle grinder and a hacksaw……..I bought a hacksaw blade once and after a few strokes all the teeth were gone.I took it back to the shop and the lady said it’s probably made for cutting wood.
Thank you for watching the video. The corner color machine has many great uses.
You do get cutting blades for more than just steel
Para afilar una broca no hace falta hacer ningún artilugio , se puede afilar a pulso con un poco de habilidad , esa broca del vídeo no parecía cortar muy bien.
Thanks for watching and sharing your wonderful experience! Wish you all the best!
How about not dulling your tooling in the first place. RPM= 3.82x constant surface feet per minute, divided by tool diameter. You spindle speed is so high the cutter is just rubbing.
Thanks for watching and sharing your feedbacks!
I use a bench grinder and I can have it just a sharp, and take half the time without having to make a jig, Americans have been using bench grinders to sharpen their drill bits for years.
Thanks for watching and leaving your comments! It’s really helpful for us! Have a nice day!
It is very, very dangerous to grind with a cutting disc.
Change the cutting disc to a grinding disc and make the video over again ...then it is cool.
The way it is now with a cutting disk is hazardous.
Thanh you. I love you
Das Holz mit ner Flex zu schneiden hat bestimmt die ganze Bude verqualmt 😅
Thank you for watching the video
Or using a hacksaw to cut timber
Thank you
good for those without grinder skills! ha ha
Thanks for watching! Have a nice day!
😏UN JOUER
Thank you!
3minutes to sharpen drill bit! After 2 hours making the equipment to hold it!!!
Thanks for watching!
Never do what he just did please. Angle grinders are one of the most dangerous tools due to the disc breaking and trying to make it into a grinder weakens the disc increasing the chance of it breaking and launching into you. Also, their not meant to cut wood. Always use a tool for what it’s meant for or you will get the trouble your asking for. Also, without cutting oil on the drill bit, you are going to heat up the metal your attempting to drill resulting in dulling the drill again. Just buy a grinding wheel and stop listening to online know nothings please. Safety first or stay home.
Thank you
Disabled people would like this. People skilled with their hands should be thankful they fo not need a guide. Not everyone has equal skills.
Thanks for watching! Have a nice day!
He’s saving his money to buy a miter saw
Thank you for watching the video and commenting, it's great for us. Wishing you a happy weekend
My old boss was a machinist in Germany before coming to the US he could sharpen drill bits holding them to a bench grinder…I can’t…and I remember him every time I can’t drill thru something 🫤
You have a wonderful Boss. As long as you do it over and over again, you will definitely do better than you think. I believe you can do it.
Nevetséges
Thank you!
A small pilot drill wouldn't go astray.
Thank you, your advice is great. Wish you always happy and happy
je moet werl hard duwen om een gat te boren hz
Thanks for visiting the channel! Have a nice day!
High Speed drill bits, need. high speed drill! Battery drills Don’t Cut It!
Thank you
The bit was still dull.
Thanks for watching!
Definitely NOT razor sharp.
Thank you for watching the video. Please try and experience it. Wishing you a happy and joyful weekend
Nunca se debe cortar madera con disco para cortar acero. Nunca
Absolutely atrocious way to use an angle grinder and cut off disk. You can absolutely explode a disk using it to grind with the side, as well as using it to cut wood. Bush league and dangerous.
Do not do this.
Thank you for watching the video and for your sincere advice. Wish you always lucky, and happy
Long winded, if you use drill bits a lot, experience and practice against bench grinder you will learn automatically correct angle to sharpen drill bit
Thanks for watching!
If it only takes 3 minutes for a razor sharp drill bit why does it take you six minutes to get to the point in this video?
Thanks for watching and leaving your comments!
Google search drill dr. Hahaha. That idea is like 15 years old.
Thanks for watching!
Ešte vodováhu na kolmé upevnenie flexky !
Thanks for watching and leaving your comments! Have a nice day!
🤣🤣🤣impressed
Thanks for watching!
Great 15 dollars is supplies and 3 hours. Just go buy a new one.
Thanks for visiting the channel! Have a nice day!
Takhle brousí vrták Pat nebo Mat?
Thank you
😵Using all the wrong tools to do a bodge job 🙄 Learn how to sharpen a dill correctly !
Thanks for watching!
😳learn how to spell 🤭 I meant drill 😡
Šikovný master nepotrebuje na brúsenie pomôcku.Uhol brúsenia má v oku.Robím to tridsať rokov.
Ale aj napriek tomu ,šikovná pomôcka.
Wow, you are so great! Thanks for watching and sharing your experience! Wish you all the best!
Fraid to say put that effort alongside a brand new drill and you'll see that grind was a total disaster .
LOL seems to be some conflict of interest .......... cool the drill while grinding but achieving the opposite with the cigarette lighter . Cant figure that one
Thank you
The lighter was used to soot the area of interest. "If soot gone, then the area is 'treated'."
Other than that, what this video shows is a total lack of understanding of which tool to use for what job.
First off, you dont use an angle grinder to cut wood. Next up is, you dont use a cutting blade for a grinding job.
Then after that, you dont need two separate 120° angles but you need to make sure your grinder is properly angled.
As you can see, the maker of this video doent care at all when it comes to feedback.
life-threatening mistake
Thanks for watching!
So ein Quatsch, diesen ganzen Krempel braucht kein Mensch, von einem Mechaniker einfach zeigen lassen wie man Bohrer schleift und dann hat man es mit etwas Übung bald raus.
Idealerweise benutzt man einen Schleifständer, bevor man beim einspannen in einen Schraubstock auch noch seinen Winkelschleifer schrottet.
Thanks for watching! Wish you all the best!
Very unsafe
Thank you
Hva betyr stalket
Thanks for watching!
You can not do this with. 016 drill or smaller 😊.
Thanks for watching and leaving your comments!
The guy that showed me how to sharpened .016 drill with a fine stone still remember until today!
Ostřím proti brusu ! NE naopak !
Thank you
That was sharp? The way it was cutting, I would be considering throwing the bit away AFTER he "sharpened" it.
Nobody has time for that. Well, maybe this guy. I mean he had an insane amount of time available to make the worst jog on the net...so there's that.
Thanks for watching!
What a load of faffing about. As an engineering apprentice, I could sharpen a drill bit by hand on a rotary grind stone.
Thanks for watching and leaving your comments! Have a nice day!
120
Thanks for watching!
Cut with a grinder? wow Not imressed
Thanks for watching!
Parksaid
Thanks for watching!
Bad workshop practice, very amateurish.
Thanks for watching the video!
That drill bit was not cutting good at all, you might want to use a lubricant when drilling steel.
Thank you for watching the video! Everything will be wonderful when we get better every day
Or run a smaller pilot drill before
Do not try this at home. Buy a bit sharpener lol
Thanks for watching!
just buy a new bit
Thanks for watching!
Ali to nije tri minute
Oh, I did it slowly so everyone could see the whole process. Thanks for watching and have a nice day!
Rubbish! Sharpness is zero. It's not a drill bit, but a grinding rod.
Thanks for watching!
🤣
Thank you!
What a load of BS.
Thank you
You should never cut wood with a steel cutting disc, ever.
Thanks for watching the video and leaving your comments! Have a nice day!
Useles vedio even children know that
Thank you for your sincere comments. Wishing you always joy and happiness with your loved ones
Фггдг
Hau weg den Dreck ... Würth Spiral Bohrer... Aller erste Sahne
Thank you
no thanks !
Looks like a bunch of bullshit to me.
Thank you for watching the video. Wishing you always find joy and happiness in life!
what a complete waste of time!
I always look forward to receiving good ideas from you. Wishing you much joy in life. I love you
Dull as dull!
Thanks for watching!
Gracias x tu invento es genial bueno para los que tengas transportador, una tuerca soldada con otra para checar el ángulo correcto y el que te haya adivinado cuantos grados debe de tener el triángulo de madera x que nunca dijiste a cuantos grados trazaste el corte con el trasportador!!!! Pero de todas maneras gracias genial yo prefiero gastar en una broca nueva pero cada quien su pedo!!!!
Thank you for watching the video! Wish you always cheerful and happy! I love you
Why the piece odf wood, just do it by hand. 👽
Thank you
Lol... You don't know anything about sharpening drills. You don't leave the tip of the drill like that (like a shovel), with a mega positive attack angle. To reduce drilling resistance, make two undercuts. Respect the tool.
Thanks for watching!
Why would you take tips off of someone who uses an angle grinder to burn through a piece of wood? Do you not have a saw? What next? Putting in screws with a hammer? 🫣
Let's do everything from the simplest things. Thank you for watching the video. Hope you have a nice weekend