You are very good, can you add links to direct people where to buy all the component you use on all your D.I.Y projects, that way you can make money from suppliers if people buy from them because of you. I like your work, it's great
Good video; Subscribed Where do you get the DC 15 Volts (Pin 12)and DC 5 Volts (Pin 14) for the EGS002? you know,it MUST be synchronized with the 380 VDC,for the IGBTs not to blow a pair..
Good work brother. See the PWD duty cycle in the oscilloscope, it does not change with the load. it runs at its maximum always.(47%). I think pin 8(PWM pulse adjustment) of the PWM module does not do the job correctly. This is a issue in this module. Any thoughts?
Why 2 circuit PCBs ? - one for switching by 3525 & another for sine wave driver pcb EGS002 ?. Can we not directly use sine wave driver pcb only to drive mosfet at the primary of transformer ?. Share the circuit diagram also.
How you try replacing the egs002 spwm ic because I have and the manufacture don’t sell the ic program the ic come blank no programming I feel so upset to speak Thousand of dollars with the manufacture and they refused to take them back and also refuse to send the program code chines company is a mess
What should the voltage be at VFB from the dc high side. With no load. 400volt or 380max. Because I find it will vary from inverter to inverter and also so very as well as the input voltage from your 12 volt site. On most inverters I find the feedback circuit is never very stable.. you did say that your feedback circuit is very important well I have seen inverters work without the feedback circuit it's tied down to 0 which is not good. And some inverters they don't like when you're running them at 14.8 or close to the 15 volts. Would be good if somebody can give more info I have an inverter which has a problem where it doesn't like when your 12-volt supply exceeds 12 volts 12.5 14.5 or maximum of 15.5 you would get flicker on the output on the 240v ac side. Yes I haven't found a solution to correct it with altering a resistor value on the pwm board which converts the 37 kHz.
I would like to see a low frequency pure sine wave inverter that runs off just solar no batteries and if possible no solar controllers and a wide input range maybe 40 to 80 volts
I both the egs002 and it didn’t work the light just blinking and when I add feedback voltage the ic didn’t respond to the feedback to stay on and the h bridge circuit I add the egs002 to the circuit the mosfet burn 🔥 as short circuit the oscilloscope show the phase not in phase so the channel or crashing into each other and ic not receiving the feedback voltage I even turn up to 5 volt and the light just blinking I remove the feedback voltage the light blinking so I need a link I can buy the original egs002 be cause a m not the first person having this issue my friend have the same issues and he’s a copy programmer and he told me the same think happened
I use the EGS002 and it needs 3 volts on pin 15 VFB, for the LED to stay steady and it works: between 2.75 and 3.25 volts; Pin 1 IFB, needs 0.2 volts It also runs on 15 Volts DC not 12
Thank you very much from California.USA. I learned a lot from this class.
You are very good, can you add links to direct people where to buy all the component you use on all your D.I.Y projects, that way you can make money from suppliers if people buy from them because of you. I like your work, it's great
Please can you share a copy of the circuit diagram?
Hi how are you
nice work you did
if 48v design how many transformer turns ?
thanks
what about the second shunt IFB pin 1. EGS can also do the current.
Good video;
Subscribed
Where do you get the DC 15 Volts (Pin 12)and DC 5 Volts (Pin 14) for the EGS002? you know,it MUST be synchronized with the 380 VDC,for the IGBTs not to blow a pair..
I made this not actually work well
In diagram you explain well but when you complete board there I not see any resistors??? Can you remake video ?
Good work brother. See the PWD duty cycle in the oscilloscope, it does not change with the load. it runs at its maximum always.(47%). I think pin 8(PWM pulse adjustment) of the PWM module does not do the job correctly. This is a issue in this module. Any thoughts?
Hi friend please which deadtime setting did you use
Why 2 circuit PCBs ? - one for switching by 3525 & another for sine wave driver pcb EGS002 ?. Can we not directly use sine wave driver pcb only to drive mosfet at the primary of transformer ?. Share the circuit diagram also.
Wao...well-detailed !
FHP20n40. are MOSFETs but in this video you said it's IGBT.. kindly any one guide plzz
Sir exelint information good job
Excelente, por favor como consigo los módulos pwm SG3828, por favor podía publicar los esquemáticos, Gracias
How you try replacing the egs002 spwm ic because I have and the manufacture don’t sell the ic program the ic come blank no programming I feel so upset to speak Thousand of dollars with the manufacture and they refused to take them back and also refuse to send the program code chines company is a mess
mantap... pak cik. share juga lah, diagram inverter nye. hehehe
What should the voltage be at VFB from the dc high side. With no load. 400volt or 380max. Because I find it will vary from inverter to inverter and also so very as well as the input voltage from your 12 volt site. On most inverters I find the feedback circuit is never very stable.. you did say that your feedback circuit is very important well I have seen inverters work without the feedback circuit it's tied down to 0 which is not good. And some inverters they don't like when you're running them at 14.8 or close to the 15 volts. Would be good if somebody can give more info I have an inverter which has a problem where it doesn't like when your 12-volt supply exceeds 12 volts 12.5 14.5 or maximum of 15.5 you would get flicker on the output on the 240v ac side. Yes I haven't found a solution to correct it with altering a resistor value on the pwm board which converts the 37 kHz.
Mas, tanya 🙏
Jadi fungsi LPF (inductor + capacitor) itu sama dengan menggunakan trafo besi ya?
I would like to see a low frequency pure sine wave inverter that runs off just solar no batteries and if possible no solar controllers and a wide input range maybe 40 to 80 volts
Hi friend,
Great job, please what's the dimensions of the transformer
That was super fast.
Excelente
Well done
Hi sir the design is great but its not not clearly visible
I both the egs002 and it didn’t work the light just blinking and when I add feedback voltage the ic didn’t respond to the feedback to stay on and the h bridge circuit I add the egs002 to the circuit the mosfet burn 🔥 as short circuit the oscilloscope show the phase not in phase so the channel or crashing into each other and ic not receiving the feedback voltage I even turn up to 5 volt and the light just blinking I remove the feedback voltage the light blinking so I need a link I can buy the original egs002 be cause a m not the first person having this issue my friend have the same issues and he’s a copy programmer and he told me the same think happened
I use the EGS002 and it needs 3 volts on pin 15 VFB, for the LED to stay steady and it works: between 2.75 and 3.25 volts;
Pin 1 IFB, needs 0.2 volts
It also runs on 15 Volts DC not 12
Boa tarde o senhor tem como me mandar o esquema elétrico que o senhorostra no vídeo da egs002
Share the diagram so that I can print it and build mine
I'm training with pcb eagle,and I see can design online with easy EDA.
make life easy. buy high voltage solar panels. they are cheaper and you can start with 380vdc
Yess you are correct...direct 380vdc feed to bus spwm and 230vac out
Mas, ini - inputnya berapa VDC?
Saya tidak ada melihat stage1 circuit (boost circuit 24(48) VDc to 380 VDc)
Stage 1 yg ada trafo feritnya.
Hi, can the schematic and pcb of this device?
NTSC for negative temperature my friend
Muito bom
Hello brother, how do I get the pcb file, thank you
uma ideia fazer ..esse circuito para usar bateria normal!!!!! agradecemos!!!!
Mohon di share skemanya tuan
Terima kasih
Salam dri indonesia
Contact me sir
kalu mlm guna lunar cell ke bro?
please share the full schematic
please link this dragram PDF link
Get the pdf..
Pls a link to download the schematic in pdf
Charge schematic pdf
Lovely,
Can you share the schematic
Sir me I request the pdf?
نتمنى منكم شرحاباللغة العربية
boleh saya minta gerber ke ?,
Gujarati translation
hey man pdf schematic
Contact me
Please can you share a copy of the circuit diagram?