Learn Solidworks in 5 More Minutes! | Solidworks Tutorial Part 3
HTML-код
- Опубликовано: 15 июл 2024
- This is a followup to our popular Learn Solidworks in Five minutes video. In this third episode you will learn to use surfaces to add features to your parts.
Be sure to SUBSCRIBE HERE: goo.gl/sYY9mu
These Solidworks tutorials run a little longer than five minutes most of the time but we try to squeeze in lots of good information without putting you to sleep.
Part One: • Learn Solidworks in 5 ...
Part Two: • Learn Solidworks In 5 ...
Part Three: • Learn Solidworks in 5 ...
Part Four: • Learn Solidworks In Fi...
Part Five: • Learn Solidworks In Fi...
Part Six: • Learn Solidworks In Fi...
Part Seven: • Learn Solidworks In Fi...
Be sure to check out some of our cool inventions here:
www.soundlazer.com
www.soniclevitation.com
www.richardhaberkern.com
#solidworks
#learnsolidworks
#learnsolidworksin5minutes
#inventiontherapy
#autocad
#inventor
#cad
#cadcam
#CNC
---
/ inventiontherapy
www.soundlazer.com/shop/
www.soundlazer.com/eurorack/
www.richardhaberkern.com
www.inventiontherapy.com 
Хобби
![Learn Solidworks in 5 Minutes+ [Part 1] Extended Solidworks Tutorial](http://i.ytimg.com/vi/WtmGGquunrs/mqdefault.jpg)
I watched this tutorials 2 years ago, completed my project, and didn't touch solid, but now another project, watching again. Good, short tutorials.
The best tutorial series on Solid Works!
I don't compliment to somebody often, but You explain your lesson very well ... Great
I love it! You inspire me to become great!
Thank you so much for your time and effort
Thank you for the great lecture
Liked and commented on every single video on your solidworks .. your tutorials are the best on here
Great tutorial!
Thank you so much sir. I am learning it from you only. Today is my third lesson.
its very helpful tqvm
thanks!!!!
Excellent! Thank you so much for your time and effort.
And Voice cracking to crack me up and not make it a boring tutorial
Thank you so much sir for this useful video.
0:50
Why go through all of this when you can just click the "Units" at the lower right hand next to the word "Editing Part."
I understood Hayf of it.
Is Creo similar to that of Solidworks?
6:15
Ethan Bennett ok boomer
My offset entities circle isn’t extruding through at 3:20. I got sw 18
simple enough, and short enough.
More to come soon.
Am I correct that when you select the two lines at 4:20 you need to use the control key?
No, just click on them so they appear in the box on the left hand side list. You can also delete sections from the left side blue box if you pick something by mistake. Many tools use this way of doing things within SW.
Following along, I had a problem drawing the rectangle at 3:50+, I discovered that if I didn't extrude the original midplane, we parted ways. Of course, I'm a beginner and could be full of it.
That makes sense that you had a problem with my way if you didn't go mid plane. My way was actually a little more confusing because I did it from the center. If you used your outside plane, you would have to chose the box tool that uses the two corners and then make sure one side of the box was along the center line of the part. Or you could also cut through the box halfway as a blind cut setting the distance to half way.
It just takes practice but the concept is simple once you grasp it.
I found that if I have your video on one screen and SW on the other screen, I can follow along and when it doesn't react as the video, I can back up and figure it out. I'm going to the community college taking beginning SW, but the teacher figures that we know more than we do, I wish you were the teacher :o)
Believe it or not, if you follow these ten videos and then just start creating your own SW models using the info here, you pretty much have enough information to build anything. The person that taught me, only showed me the steps in these videos and after that, I just started adding to the knowledge by trying things with each new project I worked on. Now I can build complete classic cars in Solidworks.
I agree, but the class forses discipline on me, I'm 75 and tend to goof off. I bought a 3d printer and a CNC router, so learning SW will enable me to get more use out of them. Thanks for your time and knowledge.
After doing solidwork what is next procissor
pro e
My offset entities is greyed out, sw 18
I redid the steps, when it was greyed i was unable to sketch on the circle face which didnt allow me to offset however now i can sketch so i can offset. Is there any explanation for this?
Enjoying the lesson however, the background music is drowning out your voice.
can someone please send me the finished object thank you i’m just trying to pass my engineering class
do u have it now?
just do it
unfortunately solidworks needs high system requirements
Actually you are incorrect. Solidworks is designed to run on the cheapest of graphics cards and average performing PCs. Detailed rendering of 3D realistic photos is slower with cheaper machines but during the design process low end machines can perform just fine.
you are right , i had a conflict between the system requirements for solidworks and inventor