Assalam o Alaikum Brother mujhe ap se analog output k liey tips chahiey. Meray pass DVP16EH series PLC with analog output module H3 ha.Me ussay incremental encoder se input de kar -10 0 +10 volts out lena chahta hun. Yani k encoder k clockwise 1 turn pe 0 to +10v aur anti clock 1 turn pe 0 to -10 volts milain. Ap k lectures are very helpful for us. Thanks slot and God bless you.
means air controller system ko auto par karna chah raha hon mein sb kuch laga hua hai bus plc ka ladder desighn karna hai digital signals ka to ladder programe bana chuka hon digital say analogue output bhi desighn kar chuka hon analogue input say digital out put bhi kar chuka hon magar analogue input read karwanay kay bad jo set point rakha hai us par analogue output working karay
sir meray pass delta dvp 20ex200r plc pari hai 4 input analog hai aur 2 out put analog meray pas aik room humidity aur temperature controller hai analog input room humadity ki 4 say 20 ma hai aur temperature ki bhi aur out put mujhay 0 say 10 volt chahiay means room huamdity meinset karta hon agar 58 to out put inverter control ho pump ka 0 say 10 volt par aur temperature agar 25 set karon to output damper actuater control hon 0 say 10 volt par agar mumkin ho to help kardain meri
@@TeckyBuzz soil moisture will range from 21% to 60% motor should start at this when the moisture level 25%, but I don’t know the analog values like the voltage or the current valuethe ideal humidity for them is around 50 to 70 percent. The motor start works when less than 50 %. When the temperatures reach uncomfortable high limits for plan should cooldown because high temperatures affect plant growth in numerous ways. The effect of temperature on plants vary widely and is influenced by factors such as exposure to sunlight, moisture drainage, elevation, and difference between day and night temperature. the ideal or optimal soil temperature for planting and growing most vegetables is 65° to 75°F (18°-24°C) for our project when the temperature high then 24°C the motor start. And because I have tank sensor The motor stop when the level of water less than 10% in the tank and give alarm. the speed of motor change by the condition above
agar plc relay type hai toh ni agar plc transistor type hai or highspeed output support karti hai toh uski data sheet m given hoga kiten high speed output port hai
Excellent explanation. In last Video 22 and here I observed how calculations are really simplified by use of Predefined register of Delta plc, what i was assuming calculations would require lengthy Arithmetic formulae and its calculations (but these, I assume are done in Delta registrars). it is more simpler because We are taking directly readings form the plc and not first calculating the input value for plc and than taking that value for o/p. Sir I know you are assuming us to be good learners, but..... Can you , See you are explaining from reading coming from memory m100, but in actual practice we have to have start/stop logic to star the m100, than m100 will take reading from x3 (or so) where sensor wire are connected. please show them, further more now we have to connect to HMI
apko kon sa interrupt use karna hai 4 tarah k interrupt hote hain External interrupt timer High speed counter communication Mnemonic hai I uske baad adress type karo woh pointer ki tarah kaam karega phir
@@shaileshmori2943 yeh rise edge tigger hai shyd. jaise ld type ho same i type karo or question mark pr click karo apko pata lag jayega jaise use karna hai . agar is se bhu help na mile toh mujhe instagram pr message kar dena m waha se bata dunga
आप बहुत ही अच्छा सिखाते है,
आपके व्हिडिओ देखते देखते सही तरह से प्रोग्रामिंग करने लगा हू, फिर से एक बार धन्यवाद❤
Very well explained sir
Hello sir
Sir aap jo video bnaate ho bhot ache se smj me aati h sir please PWM Pulse per b koi achi se video bnaao।
Thank for your compliment.
stay tunned with us
You are great sir 👍 Please teach continue 🙏
Thank you sir best video sir
Very usefull video.. Thank you sir..
Sir, how it works in plc programming that different stations are addressed for a object to be moved from a common station in ay conveyors system?
Weighing system ke liye kg ka scaling kaise karenge boss please make one vidoes on this
uske liye plc ki zarurat ni hai apko
sirf sensor or device ki zarurat hai
Boss mere pass loadcell sensor delta simulator hai or koin sa divice chahiye
SIR EK VIDEO SV PLC MODEL KE SATH EXTERNAL ANALOG OUTPUT MODULE USE KARKE KE OUTPUT VOLTAGE CHANGE KARKE DIKHAYE NA. IT'S A REQUEST
teckybuzz k instagram pr Message karo wahan pr solution provide kar diya jayega
Analog input ke bare me batiye
Sir , video to samajh aa gayi hmi se vfd run kese hogi but ek Question h vfd reference kese hum denge run karne ke liye
Please sir reply me
dose it work on DVP 06XA-S MODULE
sir jodi akta analog output video and canection kore dekhaten Valo hoto thanks sir
Bhai agr ye wala method kar liya jae plc ko vfd se connect karna ka liye to kya modbus connection ki phir zarorat nahi rehti
yes no need for modbus
direct AVI input do or drive me o external potentiometer on kar do
Thankyou bhai
i think aap smjh agye hoge ab kaise control karna hai vfd ko
Bhai aa gayi ha thankyou
Sir Siemens PLC basic Instrumentation per videos share kijiye
mera laptop kharab ho gaya isliye videos m delay hogaya hai jaldi hi videos ayengi
Assalam o Alaikum
Brother mujhe ap se analog output k liey tips chahiey.
Meray pass DVP16EH series PLC with analog output module H3 ha.Me ussay incremental encoder se input de kar -10 0 +10 volts out lena chahta hun.
Yani k encoder k clockwise 1 turn pe 0 to +10v
aur anti clock 1 turn pe 0 to -10 volts milain.
Ap k lectures are very helpful for us.
Thanks slot and God bless you.
Sir on which terminal we give input of pressure sensor if we want to control analog output control valve
means air controller system ko auto par karna chah raha hon mein sb kuch laga hua hai bus plc ka ladder desighn karna hai digital signals ka to ladder programe bana chuka hon digital say analogue output bhi desighn kar chuka hon analogue input say digital out put bhi kar chuka hon magar analogue input read karwanay kay bad jo set point rakha hai us par analogue output working karay
Thanks sir
sir meray pass delta dvp 20ex200r plc pari hai 4 input analog hai aur 2 out put analog meray pas aik room humidity aur temperature controller hai analog input room humadity ki 4 say 20 ma hai aur temperature ki bhi aur out put mujhay 0 say 10 volt chahiay means room huamdity meinset karta hon agar 58 to out put inverter control ho pump ka 0 say 10 volt par aur temperature agar 25 set karon to output damper actuater control hon 0 say 10 volt par agar mumkin ho to help kardain meri
Assalam u alaikum sir mein jab float value leti io d0 mein to khtay k float value can't taken in hexadecimal mode
apko setting m se change karna padhega
hi, good work , can you help me what if i have more than 2 sensors
use more anlog channel
@@TeckyBuzz thank you very much, I use it but I need only one output for three sensors
Thank you
tell me about your logic
@@TeckyBuzz soil moisture will range from 21% to 60% motor should start at this when the moisture level 25%, but I don’t know the analog values like the voltage or the current valuethe ideal humidity for them is around 50 to 70 percent. The motor start works when less than 50 %. When the temperatures reach uncomfortable high limits for plan should cooldown because high temperatures affect plant growth in numerous ways. The effect of temperature on plants vary widely and is influenced by factors such as exposure to sunlight, moisture drainage, elevation, and difference between day and night temperature. the ideal or optimal soil temperature for planting and growing most vegetables is 65° to 75°F (18°-24°C) for our project when the temperature high then 24°C the motor start.
And because I have tank sensor The motor stop when the level of water less than 10% in the tank and give alarm. the speed of motor change by the condition above
i don't speak Hindi but i following your step if i can send what i did by email thank you
Sir 1 plc me kitni servo Motor 1 time me chala skty hen please ans me...???
agar plc relay type hai toh ni
agar plc transistor type hai or highspeed output support karti hai toh uski data sheet m given hoga kiten high speed output port hai
Sir moje 1 plc me 4 servo Motor ko chalana ha os ky leye me kia kron...???
kon sa plc hai
Har motor me alag tarhn se ran krwana ha 1 time me kia ye mumkin ha plc me please ans me...???
@@farukhmughal7863 plc kon sa hai model number or brand batao
Sir communication ke upor khuch video banaye
Nice sir
Excellent explanation. In last Video 22 and here I observed how calculations are really simplified by use of Predefined register of Delta plc, what i was assuming calculations would require lengthy Arithmetic formulae and its calculations (but these, I assume are done in Delta registrars). it is more simpler because We are taking directly readings form the plc and not first calculating the input value for plc and than taking that value for o/p. Sir I know you are assuming us to be good learners, but..... Can you , See you are explaining from reading coming from memory m100, but in actual practice we have to have start/stop logic to star the m100, than m100 will take reading from x3 (or so) where sensor wire are connected. please show them, further more now we have to connect to HMI
Kindly show us the wiring of this program.
Please give me the total Playlist serially
sir, how can we program elevators via plc ladder logic or by c++
for how much floor?
Sir for three or more than 3 floors like 9 or 10
@@muhammaddanishhameed9865 ok Dm me on my instagram
Why we do set M1162
Nai sir me Gmail se hon apka instagram ha...?
search @tecky.buzz on instagram
Ok sir
What is the D0 in program
ISP SOFT 3.10 ME INTERRUPT KO KESE ON KARE ?
apko kon sa interrupt use karna hai 4 tarah k interrupt hote hain
External interrupt
timer
High speed counter
communication
Mnemonic hai I uske baad adress type karo woh pointer ki tarah kaam karega phir
@@TeckyBuzz muje External interrupt jese ke I001 usekarna he
@@shaileshmori2943 yeh rise edge tigger hai shyd. jaise ld type ho same i type karo or question mark pr click karo apko pata lag jayega jaise use karna hai .
agar is se bhu help na mile toh mujhe instagram pr message kar dena m waha se bata dunga
bhai plc ka data register mein jo values aa rahi hein unko vfd mein kaha connect karna ha
Sir start paid course on Udemy but Advance... there is huge demand of advanced plc course...
ok i will
Sir ap k smjane ka trika alg h smj nhi aatA h plz khuh alg se samjao
apko kya smjh ni aaya ??
@@TeckyBuzz timer ka nhi smj aya
@@nareshshiwaniwal6337 delta timer??
@@nareshshiwaniwal6337 is video ko ek baar dekhiye
ruclips.net/video/kVCB8_j5kds/видео.html
@@TeckyBuzz thx . y bhut achi trh smj ata h.pr y es softwer m khul jayega kya..
Sir can i get your email please
👍