I bought the canted version of this cage, and had the same problem with shell closing. I decided to dremel out the screwport to make room. Not you're incompetence this time walcom :)
9:40 They are not resistors, they are capacitors. They are there to cut down radio frequency noise/interference produced by the motor. They don't affect performance.
I used the canted blue cage, had to Dremel out the screwport which was rubbing against the top flywheel, I also found the screws poping up and rubbing against the inside of my flywheels, even though I was putting only 3.6v through 3 nicad aa cells
I recently bought this kit off EBay as a test for a build & was pretty sure about it but now thanks to you I'm 100% & the extra info is super helpful, Blast On Walcom ~ Captn Wolf
So I did this mod and while pushing the flywheels down the back of the motor fell out and idrk what to do now, the motor works still but the flywheels are only halfway down and I can’t push them any more
Interesting. I've always seen these listed as 12v motors. I picked up a few sets of these a while ago but havn't used any yet. Good for me as most of my lipos are 7.4v.
So there is 4 holes on the back of the flywheel cage and I've tested that u can push of the flywheels unscrew the motor and pull out the motor and you can replace it
I'm curious as to what would happen if you were to incorporate a dimmer switch in an attempt to control speed of which the flywheels spin. Would that be a possibility?
The right thing to do would be use a speed controller but a dimmer is a good high power variable resistor. I tried using one on a 1 1/2hp pool pump motor, the dimmer started smoking so I stopped.
I just ordered the canted version. I then come to learn that canted is gimmicky, and now, I'm just going to get a 3d printed 42.5mm daybreak cage and daybreak wheels. I guess I can give the canted ones away.
I dont know why but I always were my damn headphones when I watch mod videos and I regret it every time. Sweet mod though. I really wanna get into flywheel modding.
I'm sorry to tell you that these not only require 2-3s voltage - (7.4-11.6 v) they have unrated current draw. People have killed LiPos with them! AAs have no chance.
Hi Walsom S7, I recently bought an orange Stryfe because I like the look of the AK kit by Workers. I want to mod the flywheels to improve accuracy. It doesn't have to be too powerful as I am playing with just my kids. I would prefer some quiet setup. What motor, cage, wheels and switch would you recommend in 2021?
I want to put on the Workers UMP9 kit on mine but I also want to increase the performance of the blaster, not too much but enough to at least increase the accuracy and some power and I have basically the same question
Maybe for these ones, but again: I've put 132s in a few blasters without any cuts. I think what's screwing me on the Worker cage is the fact that it has that pcb that probably shouldn't be there but is there anyways.
Interesting. I have the same wheels on the way to go into my Arit red cage with Neo Rhinos. Hoping I have different result. Will be my homage to Resident Evil... I figured what better for a HvZ/Endwar primary. Thanks again C!
If you haven;'t opened a blaster before, go to goodwill and by one for cheap then open it. If you have opened a blaster and haven't done a mod, look up "Nitefinder First Mod" on youtube and follouw the instructions
Luke Baller11 my first was a blaster parts full metal hammershot kit. It’s relatively easy and EXTREMELY useful if you like the hammershot. You will use it as a sidearm for a long time if not forever.
Hey guys, I have a quick question. Can I safely use these worker 132 motors (3s, 11.1v) with a 2s lipo? Couldn't find any clarification via Google. I mean I know I can, but is it safe for the motors and the battery? Thanks a lot for an answer!
I am wondering if you know how to put this mod kit in the modulous stryfe. The internals looks a little different and I am am getting frustrated because I keep messing up and it was expensive.
I have this same kit, but haven't installed it yet, and was planning to use a 3S compact lipo; will the Select Fire kit cut the voltage enough to not over-volt these motors or should I just get a 2S instead?
Im looking to build a pretty good stryfe with fang revamps, completely rewired, what cage should i use? (I dont have a 3d printer and cant afford a rediculusly good cage like a snikkas and i dont have ANY experience. Plz help. This is a really long addon lol)
The Hexagonal Pyramid I'm sure that is a joke but I'm going to check flea markets this weekend for something that's not much money and I can practice on. Then I'll work on the brand new blasters I have
You don’t think you can keep real firearms separate from foam flingers. Go to RUclips ad settings, remove any camping, outdoor, or anything remotely gun like. Just because I love guns, didn’t mean you should see ads with them.
Hey walcom, bit late but I have only 3s lipos, I want to run these motors on 3s but they are sparking/arcing when I rev them on a 3s. What FPS are you getting with 3s? Would it be better for me just to buy a 2s lipo? I want to make these motors last.
![EINBAU WORKER STRYFE METAL FLYWHEEL CAGE + FLYWHEELS [deutsch/german]](http://i.ytimg.com/vi/dNifkXWg12U/mqdefault.jpg)
![Noob To Max With DRAGON REWORK In Blox Fruits [FULL MOVIE]](http://i.ytimg.com/vi/LnBMOinoOvA/mqdefault.jpg)
*proceeds to exceed 150fps out of a stryfe with motors ripped out of an old toy car, just to prove that the upgrade kits of all kinds are overpriced*
yeah, because not enough people buy them...
Agreed.
Jakub Komorowski-Marcjan *procedes to use old parts from my racing ex and shred through darts*
this caught my eye because I wanted to mod my nerf jolt
FLYWHEEL JOLT
LMAO
*pokemon rock music plays in background*
I bought the canted version of this cage, and had the same problem with shell closing. I decided to dremel out the screwport to make room. Not you're incompetence this time walcom :)
It's the wire gauge. I put a worker canted cage in with slightly thinner wire and it fits just fine.
Your happiness spreads like a wildfire! You really made me smile today!
What oh what could Walcom possibly have in store for poor ol' Quincy here?
WalcomS7 🤔🤔🤔
WalcomS7 A certain Vector build.
Perhaps?🐄
Hey were did you order that from I have a idea for a gun
Tha Thing NfStrike or workerkit
9:40 They are not resistors, they are capacitors. They are there to cut down radio frequency noise/interference produced by the motor. They don't affect performance.
I used the canted blue cage, had to Dremel out the screwport which was rubbing against the top flywheel, I also found the screws poping up and rubbing against the inside of my flywheels, even though I was putting only 3.6v through 3 nicad aa cells
I recently bought this kit off EBay as a test for a build & was pretty sure about it but now thanks to you I'm 100% & the extra info is super helpful, Blast On Walcom
~ Captn Wolf
RIP headphones
Why
OH GOD IM USING HEADPHONES!!!!!!!!!
@@shotgunslayer4536 mod your stryfe on lipo and youll see;)
You managed to figure out what the motor specs are for the Worker kit?
So I did this mod and while pushing the flywheels down the back of the motor fell out and idrk what to do now, the motor works still but the flywheels are only halfway down and I can’t push them any more
You should make an extension barrel with flywheels for the caliburn
that defeats the purpose of owning a caliburn. won't be as accurate
Quincy-kun said no to your advances!
Just starting cage, flywheel, motor upgrades. Do i need to put thread lock on the motor screws-- have you ever had a screw loose?
Interesting. I've always seen these listed as 12v motors. I picked up a few sets of these a while ago but havn't used any yet. Good for me as most of my lipos are 7.4v.
ED-SKaR it means longer lasting motorz
Headphone warnings are best placed before loud noises. I now require a new set of ears
Hopefully worker sells flywheel damaged ear replacement kits too
I might put a clear motor cover on it to show off those wheels
i don’t know if I am being a complete idiot, but in a rapidstrike do you really need the micro switch included?
So there is 4 holes on the back of the flywheel cage and I've tested that u can push of the flywheels unscrew the motor and pull out the motor and you can replace it
gives warning after revving
I'm curious as to what would happen if you were to incorporate a dimmer switch in an attempt to control speed of which the flywheels spin. Would that be a possibility?
The right thing to do would be use a speed controller but a dimmer is a good high power variable resistor. I tried using one on a 1 1/2hp pool pump motor, the dimmer started smoking so I stopped.
Do you know where I can find a guide that's easier to understand? I don't really know what's going on most of the time.
I just ordered the canted version. I then come to learn that canted is gimmicky, and now, I'm just going to get a 3d printed 42.5mm daybreak cage and daybreak wheels. I guess I can give the canted ones away.
I dont know why but I always were my damn headphones when I watch mod videos and I regret it every time. Sweet mod though. I really wanna get into flywheel modding.
Wow How you put a nerf dart into your id?
I put in the motors wrong...my soldering iron broke...I f*cking messed up
Samuel Gregory I’m sorry my friend, I am sorry... 😢
@@troophWVrrIor but I bought new ones ...
Ik that this kit is really meant to use with Lipo's, but will it function with the normal AA alkaline battery?
I'm sorry to tell you that these not only require 2-3s voltage - (7.4-11.6 v) they have unrated current draw. People have killed LiPos with them! AAs have no chance.
Any idea if those motors can be run on imr batteries? Or know the best aftermarket motors to use with imr?
Hey Walcom do you have to put new motors for changing the flywheels? I’m new to modding.
No shit
Nerf motors are shit
How do I put in the rev trigger switch?
Hi Walsom S7,
I recently bought an orange Stryfe because I like the look of the AK kit by Workers. I want to mod the flywheels to improve accuracy. It doesn't have to be too powerful as I am playing with just my kids. I would prefer some quiet setup. What motor, cage, wheels and switch would you recommend in 2021?
I still have the same question, even in 2022. 🥲
I want to put on the Workers UMP9 kit on mine but I also want to increase the performance of the blaster, not too much but enough to at least increase the accuracy and some power and I have basically the same question
Loving the new product reviews!
You're going to need to cut the shell/cover the motors with 132's.
Maybe for these ones, but again: I've put 132s in a few blasters without any cuts. I think what's screwing me on the Worker cage is the fact that it has that pcb that probably shouldn't be there but is there anyways.
Ahh okay, got you.
When you say elite darts don't work, would you elaborate?
Lots of burning foam. Not sure what the issue was. Basically the same issue I have every time I mod flywheelers.
Interesting. I have the same wheels on the way to go into my Arit red cage with Neo Rhinos.
Hoping I have different result.
Will be my homage to Resident Evil... I figured what better for a HvZ/Endwar primary.
Thanks again C!
Nerformance Mods it’s the weird slots on the flywheels.
He should put a compressor and a titan tank in a rapid madness from boomco that would be a really cool mod
2 large sockets on the table help to push the wheels on I have found
Hey love ❤️ your vids I’m wanting to do a first mod what do you recommend
If you haven;'t opened a blaster before, go to goodwill and by one for cheap then open it. If you have opened a blaster and haven't done a mod, look up "Nitefinder First Mod" on youtube and follouw the instructions
Firestrike with a Jolt break and AR removal.
Luke Baller11 my first was a blaster parts full metal hammershot kit. It’s relatively easy and EXTREMELY useful if you like the hammershot. You will use it as a sidearm for a long time if not forever.
What spacing is that Morpheus cage? Tks
depends. You can get it in multiple crush sizes
Ben Lam,, I know that. I was asking what spacing HE has on HIS cage. He said he was getting 150's out of that setup hence my question.
Senior XJ He says in the video.
Hey guys, I have a quick question. Can I safely use these worker 132 motors (3s, 11.1v) with a 2s lipo? Couldn't find any clarification via Google. I mean I know I can, but is it safe for the motors and the battery? Thanks a lot for an answer!
I am wondering if you know how to put this mod kit in the modulous stryfe. The internals looks a little different and I am am getting frustrated because I keep messing up and it was expensive.
If it's literally the Modulus stryfe it should be the exact same cage. If it's the Modulus ECS-12 then it's a different cage entirely.
I have this same kit, but haven't installed it yet, and was planning to use a 3S compact lipo; will the Select Fire kit cut the voltage enough to not over-volt these motors or should I just get a 2S instead?
Hi, Walcom! Can you say type of your battery, And will motors with a battery burn out? Thank you for "diy"!
Motors can always burn out, but these kinds of motors will last a long time. I used a 3s 11.4v LiPo.
Thank you!
Im looking to build a pretty good stryfe with fang revamps, completely rewired, what cage should i use? (I dont have a 3d printer and cant afford a rediculusly good cage like a snikkas and i dont have ANY experience. Plz help. This is a really long addon lol)
Would this work in a Modulus ECS-10? I know that they're basically a reshell, but with a longer barrel
It will in the sense that you can manipulate the posts somehow to fit the cage in there, but it won't be a drop-in finish.
Does this cage work with ekind waffle heads
if that extended pusher works in a barricade, I'm gonna need one for my double deuce
You can cut the scrue port out
How long did you cut the barrel tupe?
Are you going to be able to make it to Flagler?
how long does the inner barrel have to be?
Does it works with the rapidstrike?
Doesn't a longer pusher increase rpm.
Is that the bad boy that's available on Amazon
Were did the screwdriver go and how did it do so
So many choices for Stryfe. I don't know what to do with mine 🤔
try just making it your own with some creativity on the shell
I'm new at modding so I'm afraid my creativity will ruin it lol. I need to practice on some cheap ones before I try on my newer blasters
Jason Gamino why don't you do something with the jolt?
The Hexagonal Pyramid I'm sure that is a joke but I'm going to check flea markets this weekend for something that's not much money and I can practice on. Then I'll work on the brand new blasters I have
2:37 thats what she said
Good afternoon! Please tell me which motors are used here? Or how many revolutions per minute do they give out?
How do i install a lipo???
What material did you print the cage in?
I believe the cage is machined not printed.
Hugo Young as in the morpheus cage at 23:24. What material did WalcomS7 print the cage in?
ENGLISH TUITION SINGAPORE probably pla
Great tutorial!
What’s the extended pusher for
making it more consistent
and making g fire smaller darts
Stefans
Can u mod my nerf stryfe to get those motors
i prefer waffle heads to accufakes
EDM Leopard waffle head darts are better
agreed. i use the white ekind ones with UV lights.
yeah, my colors are white, hot pink and black so i picked up the white ones
EDM Leopard do the UV ones work with the star wars blasters
yes
would this fit in a rapidstirke?
The cage will. The pusher won't.
@@WalcomS7 thanks
do a tag back on the original alpha trooper
will it fit on a retaliator
The Retaliator is a spring powered blaster.
B R U H
Lol I don’t even remember commenting this must have been my little brother thanks for commenting bro
can it handle bot full auto and this kit
When's your next live stream?
Pusher arm kinda looks like an extremely small F.A.M.A.S.
i thought you needed to shell cut for 132's
just some removal of plastic from the bottom to let them fit, not a full shell cut
Don't paint the stryfe when you r done, call it "THE QUINCY"
Does this work to any nerf?
This specific one works only on the stryfe, there are some others kits for other blasters
Could you attach a flywheel to a non flywheel nerf blaster? >.>
It is possible, but you gonna have to do a lot of precise shell cutting and add a battery bay and mount a Rev switch somewhere. I did on my recon mk2
That's an afterburner, there are some kits for that
Because they last and are built out of aluminum?? And don’t catch on fire? How about that?
how many rpms?
Walcoms7 is the best
Vid was great!!!!!!
Why do you have pokemon Music
That flywheel cage looking a little sus📕
You have to take away the cut plastic thing around your barrel and it will fit entirely in the nerf gun
0:02 Walcom asmr
If i ever mod a flywheel im going to have someone else do the wiring
L a z y you didn't mod it, they guy you asked did
Cool vid man.. liked :-)
Quincy is on tip top shape.
Oof
Do a live today please
Why did I just see an NRA ad before this video? I don't even own any firearms, and I despise the NRA!
Sergio Lopez I got an ad for smosh and I haven't watched them in years.
OblivionWyvern I just hate real steel and I love Nerf, and I feel like you can't separate them anymore thanks to hie RUclips ads work.
You don’t think you can keep real firearms separate from foam flingers. Go to RUclips ad settings, remove any camping, outdoor, or anything remotely gun like. Just because I love guns, didn’t mean you should see ads with them.
Can u make me one on Etsy?
Thanks for the headphone warning jesus
You left out the most important things, how to wire up the mod. You only showed the motor wire being soldered. Not good video for a newbie to follow
Hi walcom
Pip
I'd just get a new nerf gun
1316
#53 comment
Wasted little buddy
Hey walcom, bit late but I have only 3s lipos, I want to run these motors on 3s but they are sparking/arcing when I rev them on a 3s. What FPS are you getting with 3s? Would it be better for me just to buy a 2s lipo? I want to make these motors last.
On 3S I got anywhere from 3-7 FPS more. It wasn't worth it, these clearly are over-volted at 3s.
How do i install a lipo???
BlazingTank Remove battery tray connectors, solder connector for LIPO and you should be good to go functionally
You should make an extension barrel with flywheel for the caliburn