Great stuff! Which channel are you controlling the start/stop recording with? My mode selection works, but I can't get start/stop to work (it works through other wireless accessoires like the Smallrig controller).
Bro, I have an iFlight Commando 8 , I can get the pan and tilt, but i cant Start/Stop the camera. I'm using Commando 8, DJI Ronin RS4 and a Komodo Camera. Could you help me?
Hi, if the controller does support s-bus, pan, tilt, roll, recenter and start/stop will work, changing the modes does currently do not work proper with the RS4 Pro, only for the older gimbals. if you Komodo works with the Ronin start/stop button it will with the RC controller as well
Hey, since there insn't much to find about s-bus on the RS(C)2 i'm putting it here: Can i just use the "DJI Ronin 2 UART to D-BUS Cable (Part 24)' and connect it somewhere on the gimbal itself or do i need to use the extra focuswheel of the original ronin. Used the original ronin of a friend a few times to put it under a selfbuild cablecam which i controll with the FlySky i6S + iA6B reciever which has the s-bus connection.
Hey, no problem it’s a good place to ask. You need the focus wheel to have a sbus port on the RS2 and the connect the receiver with the UART to D-Bus cable
Hi, if you are familiar with RC setups and configurations you should be able to configure it straight forward. Any specific question just ask. the Tantris sometimes have not full sbus protocol and you will therefore not be able to use all channels. There are reports that just the lower 4 channels do work most time. maybe plan for a Futaba radio to be on the save side.
@@Crapulos you need always a futaba RX and TX or any other vendor EX and TX that full support the Futaba SBUS protocol. The Receiver will be connected to the ronin S focus wheel via DJI CAN to SBUS cable.
@@BeeSView thanks. i've tried this morning. i get only red blinking on the focus wheel. dji forum is not helpfull about this. must the focus wheel calibratet on a rs2 gimbal? i hope, you have any idea.. :-)
@@artworx79 if the wheel does double red flashes it needs a firmware update, can be done via the ronin app. Single red means disconnected so no camera with focus/zoom or a focus motor is detected what will not harm the control via a RC transmitter. Make sure the slider is pointed to sbus and the sbus rc receiver is proper cabled into the focus wheel port
@@BeeSView by every start, the gimbal does an upgrade...with or without network connection. 12x or 15 x, have not counted. it blinks red slowly. in the manual is this "focus motor not connected". now, i think something is wrong with the focus wheel. nevertheless, thank you!
@@mediaoutlaws yes i use the DJI can to receiver cable out of the box, no rewire needed. I'm using the older R9 with the special 3.24 FW to simulate the Futaba protocol
Hey Mate, Just three questions. 1. I see drift on the pan axis. Can this be fixed and is the fix permanent? Don't want to be fiddling with trims every time I go to use the set-up. 2. Can you operate the roll axis at the same time as pan and tilt? The regular handles for the gimbal don't let you to move the roll axis when panning or tilting. 3. I assume the remote control your using works with the Futaba receiver? I like the look of this radio so I want to use the same. Please let me know. Very keen on this setup.
Hi m8, 1. I have no drift on any axis with that setup. Ones the center has been set it is rock solid. I have set a very small dead band on all sticks in the Jeti remote to not hit a axis unwanted while operating. 2. Yes I can operate all 3 axis the same time. You just need to make sure you are not "oversteering" any axis. If you do, then the other axis are blocked until you release the oversteered one. 3. I'm using a Jeti receiver as well (R9) with a FW (3.24) that does provide the Futaba Protocol. I use the DC16 remote because i have it for flying bigger drones. If you plan to buy one go for the kindly smaller DS16. Same functions a bit more handy and has 2 mimic type channels were you can apply roll and the control roll axis with mimic movement on the RC. Hope that will help you
Stronger than the ones from the S. The RS2 has a higher payload. I‘m waiting on the base expansion kit to have the gimbal on the car for rollers. Then I can tell you for sure. The S is fine to around 80-90 km/h until the motors will wave the flag.
@@lenart89 sbus is for DJI more the “old” protocol from their first drones. Maybe they plan some expansion with their lightbridge stuff for future, like control it via a remote from a Mavic
need some help.... how to set a switch for channel 5...3pos switch ? function curve? all other channel are working. only ch 5 doesn't. dc16 II, r9 flashed, ronins2 gh5/ gh5 mkII
Not working at all? A flip switch or a button need to be assigned. In the Sero trimming you need to make sure the channel does not go to far to or over the endpoints. It’s a timing thing as well to flip the switch. To fast or to slow will not trigger the cam
@@BeeSView ok, many thanks! shure, it works. only channel 5 doesn't work. i've tried to change the servo way....i have the endpoints at 100%. effortless...
@@artworx79 happy that I have been able to assist and solve. its a pitty that DJI removed the monitoring of channel 5-8 from the APP. That cause a lot of try&error for us guys.
Tolle Sache lass mal wieder was von dir Hören :).
Great stuff! Which channel are you controlling the start/stop recording with? My mode selection works, but I can't get start/stop to work (it works through other wireless accessoires like the Smallrig controller).
Hey, sorry for the delayed response. Start stop is channel 5. It is triggered so you need to assign a spring loaded flip switch
Bro, I have an iFlight Commando 8 , I can get the pan and tilt, but i cant Start/Stop the camera. I'm using Commando 8, DJI Ronin RS4 and a Komodo Camera. Could you help me?
Hi, if the controller does support s-bus, pan, tilt, roll, recenter and start/stop will work, changing the modes does currently do not work proper with the RS4 Pro, only for the older gimbals. if you Komodo works with the Ronin start/stop button it will with the RC controller as well
I got the setup workring with pan, tilt and roll, but how did you get it mapped to re-center?
Hey, since there insn't much to find about s-bus on the RS(C)2 i'm putting it here: Can i just use the "DJI Ronin 2 UART to D-BUS Cable (Part 24)' and connect it somewhere on the gimbal itself or do i need to use the extra focuswheel of the original ronin. Used the original ronin of a friend a few times to put it under a selfbuild cablecam which i controll with the FlySky i6S + iA6B reciever which has the s-bus connection.
Hey, no problem it’s a good place to ask. You need the focus wheel to have a sbus port on the RS2 and the connect the receiver with the UART to D-Bus cable
@@BeeSView tnx, don’t get why i need the uart to d-bus connetcor then, cauze i was connecting that reciever directly in the focuswheel
The sbus on the focus wheel is 4 pin while a standard receiver is 3 pin. If you can make that cable on your own you don’t need to buy the DJI one
Where can I find a tutorial to do your setup? You think I can use a cross fire with my old taranis? Thanks by advance
Hi, if you are familiar with RC setups and configurations you should be able to configure it straight forward. Any specific question just ask. the Tantris sometimes have not full sbus protocol and you will therefore not be able to use all channels. There are reports that just the lower 4 channels do work most time. maybe plan for a Futaba radio to be on the save side.
@@BeeSView so i have a find a Futaba !!! I can bind directly rS2 to futaba with no additional rx or tx ?
@@Crapulos you need always a futaba RX and TX or any other vendor EX and TX that full support the Futaba SBUS protocol. The Receiver will be connected to the ronin S focus wheel via DJI CAN to SBUS cable.
moin...have you tried this with a rs3 gimbal? maybe it works on the same way as with rs2 ?
Moin, yes it does work exactly like with the RS2. Ronin S/RS2/RS3 Pro working with this method
@@BeeSView thanks. i've tried this morning. i get only red blinking on the focus wheel. dji forum is not helpfull about this. must the focus wheel calibratet on a rs2 gimbal?
i hope, you have any idea.. :-)
@@artworx79 if the wheel does double red flashes it needs a firmware update, can be done via the ronin app. Single red means disconnected so no camera with focus/zoom or a focus motor is detected what will not harm the control via a RC transmitter. Make sure the slider is pointed to sbus and the sbus rc receiver is proper cabled into the focus wheel port
@@BeeSView by every start, the gimbal does an upgrade...with or without network connection. 12x or 15 x, have not counted. it blinks red slowly. in the manual is this "focus motor not connected". now, i think something is wrong with the focus wheel. nevertheless, thank you!
You’re welcome. Let me know if I can be further help you with it.
Maybe a dumb question, is there a way to setup this fiction with different rx protocol such as elrs or crossfire?
That would only be possible If DJI implement those protocols into their gimbals. By now they only talk on SBUS and CAN
Did you use the dji cable? And did you have to rewire anything on the receiver?
Also are you running the R9 access or the old version?
@@mediaoutlaws yes i use the DJI can to receiver cable out of the box, no rewire needed. I'm using the older R9 with the special 3.24 FW to simulate the Futaba protocol
can you connect this with D BUS RONIN 2?
Sure you can D-Bus equals S-Bus, might DJI liked the D better for their Brand
Hey Mate, Just three questions.
1. I see drift on the pan axis. Can this be fixed and is the fix permanent? Don't want to be fiddling with trims every time I go to use the set-up.
2. Can you operate the roll axis at the same time as pan and tilt? The regular handles for the gimbal don't let you to move the roll axis when panning or tilting.
3. I assume the remote control your using works with the Futaba receiver? I like the look of this radio so I want to use the same.
Please let me know. Very keen on this setup.
Hi m8,
1. I have no drift on any axis with that setup. Ones the center has been set it is rock solid. I have set a very small dead band on all sticks in the Jeti remote to not hit a axis unwanted while operating.
2. Yes I can operate all 3 axis the same time. You just need to make sure you are not "oversteering" any axis. If you do, then the other axis are blocked until you release the oversteered one.
3. I'm using a Jeti receiver as well (R9) with a FW (3.24) that does provide the Futaba Protocol. I use the DC16 remote because i have it for flying bigger drones. If you plan to buy one go for the kindly smaller DS16. Same functions a bit more handy and has 2 mimic type channels were you can apply roll and the control roll axis with mimic movement on the RC.
Hope that will help you
@@BeeSView awesome! Thanks for the quick reply.
do you have a picture of the connection to the transmiter on the focus wheel?
I can't post a picture in the YT comments. Please contact me via mail or Insta for the picture.
Are those gimbal motors strong? I'm thinking about trading my Ronin S with that.
Stronger than the ones from the S. The RS2 has a higher payload. I‘m waiting on the base expansion kit to have the gimbal on the car for rollers. Then I can tell you for sure. The S is fine to around 80-90 km/h until the motors will wave the flag.
Can you connect via SBUS physically using a cable, as you can on the Ronin S ?
You need to attach the focus wheel from the S to the RS2 in order to have a SBUS port.
@@BeeSView Thanks!
@@BeeSView this is kinda akward :) I was expecting the RS 2 to have SBUS port
@@lenart89 sbus is for DJI more the “old” protocol from their first drones. Maybe they plan some expansion with their lightbridge stuff for future, like control it via a remote from a Mavic
need some help.... how to set a switch for channel 5...3pos switch ? function curve? all other channel are working. only ch 5 doesn't.
dc16 II, r9 flashed, ronins2 gh5/ gh5 mkII
Not working at all? A flip switch or a button need to be assigned. In the Sero trimming you need to make sure the channel does not go to far to or over the endpoints. It’s a timing thing as well to flip the switch. To fast or to slow will not trigger the cam
@@BeeSView ok, many thanks!
shure, it works. only channel 5 doesn't work. i've tried to change the servo way....i have the endpoints at 100%. effortless...
send me your phone number to info@beesview.de. We will have a short call to solve this.
@@BeeSView very helpfull communication. thank you! the servo way is set to 55%. video on/off works now.
@@artworx79 happy that I have been able to assist and solve. its a pitty that DJI removed the monitoring of channel 5-8 from the APP. That cause a lot of try&error for us guys.
still no zoom control? :((
wieviel kanäle braucht der empfänger?
Aktuell reicht ein 8 Kanal aber DJI verspricht mehr Funktionen frei zu geben. Von daher würde ich immer min 16 Kanäle nehmen
danke für die antwort!@@BeeSView
Wie wird denn ein SBUS-Empfänger am RS2 angeschlossen? Danke!
Du benötigst das DJI Ronin focus Wheel und das DJI Ronin 2 / Ronin-S - UART to D-BUS Cable (Part24) dann kann der Empfänger angesteckt werden.