10w LED - Solar Rechargeable Light | Power Full | Experiment | Low cost
HTML-код
- Опубликовано: 18 май 2018
- This video makes a Rechargeable Solar light (10w LED)
using a 6v Solar panel and 3.7v mobile battery with DC-DC boost converter module(3.7v to 12v)
www.utsource.net/ - is a online platform for electronic technicians, Makers, Enthusiasts, Kids to find electronic components
----------------------------------------------------------------------------
Download detail and Circuit diagram -goo.gl/TjFLNg
goo.gl/vLdYrJ
----------------------------------------------------------------------------
the component is using
1) 6v Solar Panel
2) 3.7v battery
3) DC-DC boost converter
4) 10W SMD LED
5) LM7805 5v regulator
6) 1N4007 diode
7)100ohm resistor
8) switch
9)3mm LED
-------------------------------------------------------------------------------
Buy this material in the online
1) 10w SMD LED - goo.gl/NFBtTV
2) DC - DC boost converter module - goo.gl/pKbCHe
3) 6v Solar panel - goo.gl/CLfFhY
4) 1N4007 diode - goo.gl/X71hCp
6) LM7805 5v regulator - goo.gl/rVQ3BQ
----------------------------------------------------------------------------
buy more material by the following a link
MINI DC 0-32V 3-Digital LED Display Volt Meter
Banggoog - www.banggood.in/custlink/vvDD...
Amazon - amzn.to/2P6vR12
Solar LED Wall light
Banggood - www.banggood.in/custlink/DDDm...
Amazon - goo.gl/48Kxnb
3S 20A Li-ion Battery 18650 Charger PCB BMS Protection Board 12.6V Cell -
Banggood - goo.gl/7jfnBM
Amazon - goo.gl/uy6YwM
LM2596 dc-dc buck converter step down module =
Amazon - goo.gl/pxH5AR
Banggood - goo.gl/eg6WSn
MT3608 2A dc-dc Step Up Boost Power Module =
Amazon - goo.gl/c4Ys6P
Banggood - goo.gl/pKbCHe
------------------------------------------------------------
Click the link see the more videos on the playlist
1)Monitoring & controlling project circuits - goo.gl/UUT2CG
2) Inverter circuits - goo.gl/xz33Uu
3) Chaser LED lights circuits - goo.gl/5aRnU4
4) DC Power supply circuits - goo.gl/yt4fuP
5) Remote control circuit - goo.gl/rJzx1d
6) LED-based circuits - goo.gl/pga5qh
7) Relay-based circuit - goo.gl/Q4r7XM
8) PIC Microcontroller project - goo.gl/9tNaVm
9) Relay-based circuit - goo.gl/J4u8BD
10) Battery controller circuits - goo.gl/YVHokC
11) Repair works - goo.gl/11uPxn
12)Transformerless power supply circuits - goo.gl/c9zv
----------------------------------------------------------------------------
buy this material by the following a link
1. Electronic Components Project Kit or Breadboard, Capacitor, Resistor, LED, Switch =goo.gl/1mBi3L
2. 1N4007 Mic 1A 1000V DO-41 Rectifier Diode Set Of 10 = goo.gl/X71hCp
3. DC 0.9V-5V 0.6A USB Charger power bank Module goo.gl/ZpP9eE
4. Dual USB 5V 1A 2.1A Mobile Power Bank Module =goo.gl/5TKcMi
5. DC Boost Converter Power Supply Module = goo.gl/c4Ys6P
6. 433Mhz RF Wireless Transmitter Receiver Module = goo.gl/ZntXYr
7. 10W mini White High Power LED SMD Bead Chips = goo.gl/NFBtTV
8. 12V DC Battery Eliminator Power Supply transformer-1 Amp = goo.gl/nBE6P3
9. LED driver AC TO DC 12V CONVERTER = goo.gl/NMf1Vh
10. 555 Timer Ic = goo.gl/ZPB1Zt
11. 1W High Power Led Lamp 110-120Lm LEDs = goo.gl/3NuufG
12. 12 Volt DC Motor (Multipurpose Brushed Motor For DIY Applications PCB Drill) = goo.gl/RVHTQK
13. DC 12v gear motor = goo.gl/M3yqZL
14. Electric Hand Drill PCB Press Drilling 12V Motor, 12000 RPM, 10 Pcs 0.3-3.0 mm Drill Bits Set, Keyless Brass Chucks and Hi-Watt Battery = goo.gl/7qUf9m
15. 12V PCB MOUNT SUGAR CUBE RELAY = goo.gl/m1pbD9
------------------------------------------------------------------------------- 
Наука
![Latto - Sunday Service (feat. Megan Thee Stallion & Flo Milli) [Remix] (Official Video)](http://i.ytimg.com/vi/9gL0F1xIt2I/mqdefault.jpg)
great video!! more videos like this would be cool
Amazing idea!
very nice video sir and information
Super experiment sir...👍👍👍👌👌
Хорошо в Африке,солнца много и зимой акум не замерзает!
P.G. good job!!! :)) subscribed!
Thank you very much for the simple curcuit need something like that for my rechargeable camp light project😎
You can burn your house or camp without charging control unti for battery
@@khaledaboizzat i know it's dangerous so i put a 2 hour timer in the circuit between the solar cell and the cells.at full sunlight it's just enough time to charge before the timer cuts power...had a couple of those timer circuits laying around and they were small enough to fit in the lamp so i put them in..as for the performance they work really well for the the 4 nights i was camping, left it on all night so to discharge them before the day and if they didn't discharge fully i also put a switch on the solar panels just in case they don't . as i'm back home all the switches are off so no charging is taking place when the lamps are not in use. i do take them out for time to time to charge and discharge just to keep them working so I'm not worried ......just have to think a little to solve those problems and hey i love a challenge anyways lol
@@khaledaboizzat and he did say low cost which i was looking for i live in the Caribbean and those part are more then a couple cents where I'm from
@@tallman8ft bro for how much time I have to keep it in sunlight
@@naveennaik1054 had it out for half a day in full sun on the beach for about half the day 6v solar panel checking the batteries makesure they not overheating and also with a multimeter
Good experiment
Very nice
Nice work but you battery is gonna spoil very easily. But it is a nice work.
Nice video, however I wouldn't use a booster PCB to increase the voltage as they waste power. Have more batteries.
Awesome man. thanks
POWER GEN please please replay me almost done the citcuit of full bridge rectifier but i have a problem is i have a centetaped transformer of 13v transformers I checked with multimeter when i tough the 1 and center wire of transformer i get 13 v and when i tough center and 3 wire i get 13v but when i tough 1and 3 wire i get 27v can i use thise transformer
Genial.
A good idea, but I would advise putting a BMS on this battery or using the one built into those tp4056 boards because that way, without protection, it can overload and, in the worst case scenario, burst into flames
ok, i agree
Could I add to this circuit with an auto on/off LDR driven system between the power source and DC booster circuit without using a manual on/off switch?
Bhai y solr panl ka chrger h??
Y batry achhe s charge lega plz cmnt m btao
Sir.. Can I use 12v panel.. For lighting
Nice pari circuit mein hum 12 volt dc ka use kar sakte hain ya nahin
Super
Nice tutorial to make a bomb
really like
VERYYYYYYYYYYYGood Ideaaaaaaaaaaaaa............
Tuyệt vời
Muy bueno el video 👍, mi consulta es: cuanto tiempo dura alumbrando?
Lo ideal de éste sistema seria colocarse un sensor pir...para que alumbre al paso
good
On these types of videos you always get the wannabe electronic engineers commenting on how they wouldn't do this, or how this is bad or that is bad ......how about you congratulate the guy on actually giving it a go, actually building something instead of wasting his life on alcohol or drugs !!!!
does it charge during the day and turn on automatically at night?
otimo projeto, mas dura quanto tempo ligado
Hello hi ! The battery discharge quick.if connect the ampermeter to pozitiv battery current drain with 3000 ma.
What kind of transistor is colo cando and the iodine that capacity describes what
dc boost modul lagane se 12v battery charge ho sakta hai 4v se
bro, such as a Solar 10w panel, can I join it in a step down? thank you
Can u give me a circuit with 2 solar panels, 2 boost converters, battery and LED with ring network. What changes should I make compared to this?
Nice mode to burst battery
100ohm resistor 1 Watt wala hai kya ?
Can dc-dc buck booster work for all I/p voltages or suitable if sir can you give ratings of it & cost of it?,is it not possible to charge battery with out is regulator ? If yes then tell me what is purpose of it? What is ratings of the led bulb ?
Do u have power bank circuit
Mmm las tensiones son correctas el problema es que la corriente necesaria de carga es de 2800 mA/h y ese circuito no llega a ese valor ...por lo cual los testigos se prenderan como si cargara pero no cargara nada o tardará 5 dias en cargar ...yo hice uno de esos y falló
The performance of this panel is at such a low level that it is almost impossible to charge this battery. I think it's about 30-50mAh. It takes 5-6 pieces to make sense, even with that number, it would take many, many hours.
I don't say anything about the connection itself, everyone can see that no charging module has been used.
Do it right and show it, plus for creativity. ;)
What is the battery charging time and backup time in hrs ?
Can I replace 12 v solar panel so that will charge much faster than that?
Yo man could you make a video on how to connect a motion sensor (PIR) to this circuit in order to turn it on
Tom,
Did you ever get what you requested?
Thanks
I have 12v solar panel.. So hw many LED's can I use and how much range of battery I want to use..? Plz tell me
a 7805 regulator to get 5V from 6V? You know that it has a voltage drop? Instead it makes more sense to use a zener diode with bipolar transistor to charge to get a fixed voltage
That is a really great design. Can somebody please tell me how I can add a sensor so the light turns on at night only. Thanks again
ok i will try and upload
I think you should use light sensor instead of switch to auto light on in night
Backup kitna der deta he
use tp4056 charging module except 7805 ...for your safety
without the switch , the led will turn on automatically after solar panel is in dark ?
not bad
How low will the DC to DC boost work? The lithium iron is it overdischarged protected?
Yes, there is this circuit without protection.
I will upload a video for the protection circuit
Hi Power Gen, what type of cable did you use for this project?
It's very compocated
Pool Oo
Very much useful... 👌👌
Thank you
Can you make irf44zn?
good project
HOW DO YOU ADD A PIR SENSOR TO THIS CIRCUIT?
How of i use Cell charger because i have no solar. Pls give me the diagram.Tks
Nice mujeh bi banana he kitne pese me ban jyegi pabrbenk
1. No protection circuit used for charging battery
2. The ampere output of solar panel is too low to actually charge the battery. Most of such panels provide around 100ma of current.
Do you know how long a charged battery last with a 10 watt led light on?
Sai quanto dura con batteria carica una luce da 10 watt sempre accesa?
10 W / 3.7 V ≈ 2.7 A
Akk. is 2800 mAh, i.e. 2.8 Ah. 2.8 Ah / 2.7 A ≈ 1 h. That is max 1 hour.
Very hot for a long time
It should be used with a motion sensor. this LED consumes the battery very much. It will not even give you two hours of direct calling. already with a motion sensor, would last all night.
good video, thanks
Thank you for support
how many hour the light can be on i think this light will be on for one hour
I did this exactly 20 years ago!
Mera pass bluetooth speaker hai ousa bass nahi aati hai kya kara
How many times u get that light
Really? Charging a Li-Ion cell without using a Li-Ion Charger-IC? I can see your house burning down.
You need a Over and Undervoltage, also a overcharge protection for this Li-Ion. Also Li-Ion cells gets charged with "CC-CV" Constant Current, Constant Voltage. You need a constant voltage of 4.2V and about 1A, less or more dosnt care. As long the current is about 1/2 capacity in mA.
Better buy a $1 IC called "TP4056". Its made for charging Li-Ion and Li-Po cells. It provides a CC CV, also a under and overvoltage protection, also an overcharge protection.
People here: DONT copy that build or your house will burn down. Use a TP4056 and this circuit wont be a problem anymore.
Some batteries have bms build in it but his isnt
hallo Andreas,
ganz so schlimm wird es schon nicht werden, dass er seine Hütte in Schutt und Asche legt ;-) er hat ja eine Diode in die 5V Leitung zum Akku geschaltet, also kommen dort ohnehin nur rund 4,3 V an. das eine Zehntelvolt, um das die maximale Ladespannung jetzt noch überschritten ist, verbummelt sich in seinen Leitungen und Anschlüssen :-)
zusätzlich kann das Solarmodul unter günstigten Voraussetzungen maximal 100 mA liefern. wenn ich von meinen Vorausetzungen ausgehe (= 8 Sonnenstunden/Tag) dann braucht der Akku mehr als 5 Tage, um auf seine volle Kapazität aufgeladen zu werden. nachdem der Akku im Video auch schon einige Zeit am Buckel zu haben schient, hat er in der sonnenlosen Zeit bestimmt eine hohe Selbstentladung, sodass er ohnehin nie seine volle Kapazität erreichen wird.
meine erste Idee beim Zuschauen war auch: warum nimmt er kein Modul mit einem TP4056 und vielleicht auch noch mit einem DW01A drauf, dann hätte er gleich 2 Fliegen mit einer Klappe erschlagen. sonst muss er den Tiefentladeschutz anders bewerkstellingen, denn der MT3608 in seinem Aufwärtswandler arbeitet bis ungefähr 2 V hinab. somit ist die Entladespannung des Li-Ion auch schon lange unterschritten. also lange halten wird er nicht.
und ich gebe dir recht, ein solches Ladegerät zu bauen ist leichtsinnig, da Li-Ion auf Überladung brandgefährlich reagieren. bei dem Mini-Solarmodul sehe ich nicht die große Gefahr, aber der nächste schließt an Stelle des Moduls ein leistungsfähiges Netzteil an, tauscht den 7805, der auch schon bei 1A abregelt, gegen einen Regler aus, der mehr Power liefert und dann kann der Akku tatsächlich anfangen zu brennen.
gruß,
Stefan
ps: gute Fahrt und achte auf die Bodenwellen ;-)
@@stefanmoser4348 english please
Agree.
@@stefanmoser4348 schön die kommentare auf deutsch gehijacked. naise sache :D
Charger kitne ka h y sir btao plz
how if led is 30watt, what must i change?
can you pls upload circuit diagram
Hi, I'm a beginner in terms of electric circuits, and I will make one of this for my science class. Can I make it a parallel circuit?
*Can I add 2 10w SMD led and make it a parallel circuit?
I am not sure what the boost converter is rated for as far as current goes you have to be careful to understand the limits of all of the components, but it should work.
components ka description ?
How many hours work light
Can I use an NiMH battery? What would be the difference? Thanks so much for this
yes, you can use the connect 3 Ni-Mh battery in series(1.2v +1.2v+1.2v =3.6v required)
Your NiMH batterys wont burn that fast as this Li-Ion battery.
@@powergen522 how this project works please write working principle of this project in description.
Power gen can u tell me that for How much time I have to keep it in sunlight can u tell me plss
Reply fast broo
Sir cost analysis bata sakte h
Over charger?
can you do a 12 v dc light bulb,,, stay on for seven days,,with no charge..
i can't understand
3W led is also enough in this circuit
how many LED can i install
Ye kitni der tak jalega
Iska diagram to bata dijiye
With that solar panel, it will work, once a month.
Que peça e essa
Don't you want the diode to block voltage from the battery to the solar panel. Why put the diode between the 7805 when there's nothing to block?
the diode is forward voltage direction only and solar panel 6v 150mA so charging voltage is enough
Never seen soldering done with a poker and no solder
Hello brother mere pass Rated maximum power (3wp) hai aur aur is solar panel per voltage at pmax (8.25V) mere pass hai please iska video karke mujhe bhej sakte hain 😣😣😣🤞🤞🤞🤞😞😟🙁
Solar panels Kha milga place add... Ham jharkhand so hi
online market,
Amazon, Flipkart
Battery backup should be 30min tops
It will charge the battery while keeping in sunlight
Iti ici tr nya brapa
Is circuit mai 775 motor chal dakta hai kaya
cannot run 775 motor because of the module may be damaged due to overheating produce
Thank you 😊
Where is current breaking circuit
5v regulator ok. (3.6 v step down converter????)
this is a step-up converter
step up converter 3 v to 24 v chalega is project main???
Working time of the led?? how many hours?
Depend on the capaciti of the battery
Need some explanation ..
What if Face that Solar panel near to light.... Then unlimited source of energy on loop...
Back up time??
I have a 9v 100mah solar panel can I use it?
yes can you use it but you will connect the same circuit
5v - 0,7v=4,3v
Li-ion 4,2v !!!!!
Explose.