Thanks. You helped me figure out my 2008 had a bad relay. 8 dollars next day and I bought a pack of 4 with 5 pins,works like a charm because there is an empty slot for that 5th one. Also I wasn't able to tap on mine and make it run it just wouldn't but after I put 12 volts through the middle one and it made it come on I knew. Thanks again. Also I noticed mine was coming on then stopping then coming on the day before it just stopped working, i bought mine with the radiator relocated and snorkeled so I could see it easy
You do awsome videos ,and there never to long.if you would have shown me the circuit breaker I wouldn't have know now I can disconnect my toggle switch .with the plug end from a old stater hooked to a toggle to bat.also your a good teacher,very easy to understand better than partzilla. Awesome keep up the good work .Wayne from Calgary alberta
Awesome Video! I have a 2007 and its exactly the same and you made it to easy to track and find the problem and of course it was the last thing i checked which was the circuit breaker in the rear just came unplugged at one of the circuit breaker.
thank you very for this video it helped me a great deal. I found a mouse nest in the back destroying all the wires and the fan circuit breaker!!! again thanks.
Nice vid good info thanks. If your not keen on removing all the back to access the circuit breaker you can remove the plastic tool box and gain access thru that way (just one screw at the bottom .
constant on/off many times would cause it to wear out quicker than other ones nothing electronic lasts forever especially switch contacts in the relay and the electromagnet in the relay and theirs springs in it that can wear out over time and heat and the cold
My fan is not working.. Followed your steps but using paper clip no fan... Looked at relays and my 2012 700 EPS model does not have a 3rd relay... I only have 2. Stumped on what to look for next
That doesn’t totally make sense. Any atv if it’s running warm you can turn the engine off and leave the key on so that the fan runs and cools down the radiator. If that thermostat is jumped and the key is on the fan should run.
Having overheating on 2004 600 grizzly, heard the fan running so assumed it was OK and started thinking weak water pump. Your viedo helped will now jump temp sensor to confirm fan running continuously. Any thoughts on troubleshooting water pump and thermostat. I started rig cold with radiator cap off and waited to heat up trying to see increase flow through radiator as the thermostat should have opened. Didn't see what I expected as more water flow. After testing fan will replace thermostat and waterpump. Am I overlooking anything else I should check?
Before replacing anything you should check both sides of the radiator, feel the hoses and verify they are both getting hot. If they are then it's flowing coolant. Water pumps on these machines don't really become weak because they are so basic. They either work or they leak "pretty much ". But also make sure the actual radiator fins are clean, if it's plugged up with mud etc it's going to run really hot. Then you need to continue to follow it through. Also how is the coolant level? I'm thinking it's ok considering what you have done, but also has that ever been changed? Because coolant does deteriorate over time, especially if it's original. Before buying parts you have to verify everything. Hopefully this helps.... thank you
I'm not positive what they may have changed on other models, but they might have mounted them in another location... should still be close to the battery and fuses etc.... Thanks
Hello. Can oyu please tell how to delete fault code on grizzly 700 2007 I can not wire for grounding with EPS controller. Maybe it is different for 2007 and 2008.
This is exactly what is happing with my machine. I tested fan with auxiliary battery… it turned on. I plugged fan in, I started the machine and the unplugged the thermo connection and then the fan turned on before I put the paper clip in!
Hello. Can oyu please tell how to delete fault code on grizzly 700 2007 I can not wire for grounding with EPS controller. Maybe it is different for 2007 and 2008.
Hello. Can oyu please tell how to delete fault code on grizzly 700 2007 I can not wire for grounding with EPS controller. Maybe it is different for 2007 and 2008.
Thanks. You helped me figure out my 2008 had a bad relay. 8 dollars next day and I bought a pack of 4 with 5 pins,works like a charm because there is an empty slot for that 5th one. Also I wasn't able to tap on mine and make it run it just wouldn't but after I put 12 volts through the middle one and it made it come on I knew. Thanks again. Also I noticed mine was coming on then stopping then coming on the day before it just stopped working, i bought mine with the radiator relocated and snorkeled so I could see it easy
Your very welcome.... I'm glad it helped... Thank you
You do awsome videos ,and there never to long.if you would have shown me the circuit breaker I wouldn't have know now I can disconnect my toggle switch .with the plug end from a old stater hooked to a toggle to bat.also your a good teacher,very easy to understand better than partzilla. Awesome keep up the good work .Wayne from Calgary alberta
My fan was seized, this helped confirm that. Thank you.
Thank you very much for the video, followed your instructions and found bad relay, just like yours. You are very good at explaining. Thanks again
Awesome Video! I have a 2007 and its exactly the same and you made it to easy to track and find the problem and of course it was the last thing i checked which was the circuit breaker in the rear just came unplugged at one of the circuit breaker.
Great job, I now have the confidence to try this myself!!
thank you very for this video it helped me a great deal. I found a mouse nest in the back destroying all the wires and the fan circuit breaker!!! again thanks.
No problem, I'm glad it helped... It was the first video I ever messed with but.... you get the picture....
I had the same issue, I had to splice in a new circuit breaker
Nice vid good info thanks. If your not keen on removing all the back to access the circuit breaker you can remove the plastic tool box and gain access thru that way (just one screw at the bottom .
Great video ! Is there a part number for that relay ?
Awesome job on the video, very thorough! Thanks.
Very helpful 👍
Awesome video!,!!! My problem was in the rear end area mouse ate the wires: Thanks you ,,
Excellent video. Curious why that relay would go bad?
constant on/off many times would cause it to wear out quicker than other ones nothing electronic lasts forever especially switch contacts in the relay and the electromagnet in the relay and theirs springs in it that can wear out over time and heat and the cold
Very clear and precise explanation. I have a 2003 yamaha grizzly 660, so I am wondering if there are any major differences???
My fan is not working.. Followed your steps but using paper clip no fan... Looked at relays and my 2012 700 EPS model does not have a 3rd relay... I only have 2. Stumped on what to look for next
same, what did you find out?
@@EkonRekon replaced fan with a new one and everything was perfect.... Just order a new fan.
@@EkonRekon I hit the back of my fan with a wrench and it started moving. I knew it was the fan motor.
@@SouthFLMudClub hahaha I just read this after finding out the same thing!
@@EkonRekon them sum bitches is expensive. Im sure they have gone up too but its necessary
King of what not
Money!
That doesn’t totally make sense. Any atv if it’s running warm you can turn the engine off and leave the key on so that the fan runs and cools down the radiator. If that thermostat is jumped and the key is on the fan should run.
Having overheating on 2004 600 grizzly, heard the fan running so assumed it was OK and started thinking weak water pump. Your viedo helped will now jump temp sensor to confirm fan running continuously. Any thoughts on troubleshooting water pump and thermostat. I started rig cold with radiator cap off and waited to heat up trying to see increase flow through radiator as the thermostat should have opened. Didn't see what I expected as more water flow. After testing fan will replace thermostat and waterpump. Am I overlooking anything else I should check?
Before replacing anything you should check both sides of the radiator, feel the hoses and verify they are both getting hot. If they are then it's flowing coolant. Water pumps on these machines don't really become weak because they are so basic. They either work or they leak "pretty much ". But also make sure the actual radiator fins are clean, if it's plugged up with mud etc it's going to run really hot. Then you need to continue to follow it through. Also how is the coolant level? I'm thinking it's ok considering what you have done, but also has that ever been changed? Because coolant does deteriorate over time, especially if it's original. Before buying parts you have to verify everything. Hopefully this helps.... thank you
I'm not positive what they may have changed on other models, but they might have mounted them in another location... should still be close to the battery and fuses etc.... Thanks
Thanks..great help
Thanks for the vid 👍👍
Can I bypass the circuit breaker and wire it directly? What would happen?
On my kodiak the fuse box is under seat but no relays i wonder if its under the front fender.
Does this apply to the 2013 model year?
Hello. Can oyu please tell how to delete fault code on grizzly 700 2007 I
can not wire for grounding with EPS controller. Maybe it is different
for 2007 and 2008.
Не подскажите размеры радиатора Гризли 700 ?
THANKS!
Do you what is the 2nd and 3rd relay for will like to know
i beleive what he has labeled #2 is fuel pump relay, the middle one
What if the fan only runs when I pull the thermal sensor without the paper clip in it?
This is exactly what is happing with my machine. I tested fan with auxiliary battery… it turned on. I plugged fan in, I started the machine and the unplugged the thermo connection and then the fan turned on before I put the paper clip in!
So what does that mean?
excellent video, I got some troubleshooting to get too
skip the first 1:30.
Hello. Can oyu please tell how to delete fault code on grizzly 700 2007 I
can not wire for grounding with EPS controller. Maybe it is different
for 2007 and 2008.
Hello. Can oyu please tell how to delete fault code on grizzly 700 2007 I
can not wire for grounding with EPS controller. Maybe it is different
for 2007 and 2008.