How To: LG/Kenmore Washer Seal 4036ER2004A
HTML-код
- Опубликовано: 22 ноя 2024
- How To Replace: LG/Kenmore Seal 4036ER2004A www.appliancep...
Symptoms: Bearings have gone bad and hearing a grinding noise; or seal is bad and getting water leaking out of back of tub
Tools: Phillips screwdriver, flathead screwdriver, 10mm socket with long extension, wire cutters, 17mm socket, 13mm socket, pliers, 12mm wrench, piece of wood, hammer, punch, nylon or brass brush, liquid soap, thread sealant, vice grip pliers.
To help remove the inner tub from the outer tub, as well as the bearings from the outer tub, you can use Rust Buster (www.appliancepa...) or any type of penetrating oil. This LG/Kenmore made Washer Seal replaces the following older part numbers on LG Washers: 1267489.
Buy the new Washer Seal 4036ER2004A here: www.appliancep...
This video works for the following Washer Seal and Bearings:
4280FR4048E www.appliancepa...,
www.appliancepa....
Most orders delivered in 2 business days or less.
If you enjoyed this video, please click the like button. Subscribe to this channel for more appliance repair tutorials.
If you need any more technical advice, call us at 1-877-477-7278 or chat with us on our website www.appliancepa.... Our friendly team in the United States is available 7 days a week.
For more appliance advice, information, and tips, follow us on social media.
Facebook: / appliancepartspros
Twitter: / applpartspros
You carried me through my bearing(s) repair. Could not have even considered the project without your video. I am a 72 y/o (female). I watched your video 3 times before I 'knew' I could make the repair! At the start I had your video running as I followed along. My daughter helped me get out the tub and away I went. I can't thank you enough for your detail. It took me 4 days at a 'slow as you go' pace. I didn't want to 'screw it up! As I am writing this, the washer is going through it's cycle. SO QUIET. Oh, the LG TROMM Steam Washer is 13 years old and now runs like I just had it installed! Thank you so very much.
You go girl, ;)
I am in the middle of doing it right now. I'm 65 years old and an aircraft mechanic. So got the experience to perform it. Well done on your part. And I do 'when in doubt, go slow.'
Mam i am habib from bangladesh i am good technician
for all washing machine and refrigerator repair so ples:halp me for job on your country.
6 years later and still saving people money! Thank You! Couple of notes. 1) I agree that placing the weights on after boot gasket install is easier. 2) seal placement shown in video is correct despite comments. 3) take the time to clean the tub parts during the process. I pressure washed. 4) I had to let penetration oil set for a while to release the tub and the bearings. Those took the longest amount of time.
Great DIY video. My washer was making a horrific grinding noise and inner bearing was pooched. Inspection of the stator showed some wear due to alignment issues from bearing. Took about 1.5 hours for tear down, 30 minutes for bearing removal and replacement (including tub cleaning and tub main gasket leak test) and about 2 hours to reassemble. The extra time was to double check connections. Despite wear on the stator, washer is back in working condition and sounds very much like it did when brand new 10 years ago with the new bearings. If you use softened water plan to replace the spider arm assembly as mine was terribly pitted from chloride corrosion. Thanks to AppliancePartsPros for saving me several hundred dollars in labour from a repair shop....kudos!
Awesome, glad you were able to get the washer fixed up!
Christ, reinstalling the gasket clamps was the hardest part! I ended up using a hook tool, reached up to the little tab on the gasket spring and levered it over. About 1000 choice words but I got it. This video series is a life saver though, totally disassembled a washer utilizing it. Cleanded every bit I could and now reassembling. Thanks a million.
0:28 "It's gonna be a very easy repair" ... was it hard to keep a straight face when you said that?! I've literally followed these instructions three different times, and it has never been "very easy." But it would be impossible without this great video, so thank you once again.
Glad the video was able to help you out. If you have any questions please let us know!
Called LG and they declined to fix my 9 year old washer under warranty. Said the motor was bad (10 year warranty), but they don't stock parts for machines older than 7. Their fix? Buy a new LG and they'll refund me 15%. After my diagnosis with the help of some internet surfing, I deemed it faulty bearings. $80 in parts, some very handy video tutorials, and I've got a VERY happy wife! THANK YOU for taking the time to make these videos...keep up the great work!
This is truly one of the best how-to videos I have seen. Bearing seal on my had deteriorated and corroded the bearings until it was making a hellacious noise when it was spinning. It helped that I have the exact model number.
One MAJOR suggestion - a safety note from which everyone can learn from my mistake: while stretching the spring clamp around the door gasket, my tool slipped and I ran my right hand right up against the sharp sheet metal edge of the frame and sliced the ever lovin' "you-know-what-ie" out of the back of my hand. Deep cut, bled for hours, and though it didn't require stitches, it did take several butterfly band aids. Take it from me, wear gloves, or put some tape over the edge of the sharp metal edges, or both. Otherwise, thanks for a great video.
Rich Borel Good job on getting the washer fixed up! We do wear the gloves for a reason, sharp edges everywhere!!
I just did this repair today - I just paused the video like a kazillion times during the process, lol. Turned out whisper quiet and works perfect. My unit is 10 years old. This repair took me 6.5 hours and cost 30 Bucks for the 2 bearings, seal and tub o-ring online ..way better than spending $900 - $1,000 ..thanks for posting this video!
Thanks Appliance Pros and Matt for a great video. My son and I followed step by step on my cell phone in the garage and had everything back together and a load of laundry being done in 4 hours! The lighting and close up views of the work being done were perfectly shown and Matt explained each step as he showed how to do it at a easy to follow pace. Couldn't of done it with out you guys, thanks again.
He is very clear and to the point. You do not need a Ph.D for washer repair, all you need is a guy like him to explain and you can get the job done. Thanks for a wonderful presentation.
Two words; Thank you! Your detailed, clear, and graphic instructions helped me to reach a successful endeavour. Moreover, as a video producer, allow me to give an A+ to the indiividual in charge of the shootings. It's a good lesson for those who dare to upload very poorly done video images.
Thanks, I am glad the video helped you out, I will pass the compliment along!
Yes I should have added to my comment that the video quality was especially helpful. Well-lit, close up shots made it clear exactly what to do.
You are the Bob Ross of washing machine repair! Not only is your video extremely clear and thorough, you have a calming voice that is keeping me from hurling tools across the room. Bearing replaced, shocks replaced, spider arm replaced...now wish me luck getting the rest put back together!
You are welcome! Glad you were able to fix your issue! If there is anything we can help you with in the future please let us know.
@@appliancepartspros Mam i am habib from bangladesh i am good technician
for all washing machine and refrigerator repair so ples:halp me for job on your country.
This video is incredible! I watched this on my laptop in my basement and followed step by step. It was great. I knew from the start the rubber tub seal was going to kick my butt and it did. The whole project cost me $40.00 for the bearings, seal and tub gasket. Thanks so much for posting this!
This is the best DIY video I have ever seen. Very easy listening and straight forward. Ive tried two other issues that cause an LE code and neither fixed the problem. When I noticed the binding going on I pulled this video up from University of Tube. I haven't even begun to take my washer apart yet except for the back side. Im actually looking forward to this job. I especially love the comments the 72 yo lady below made. Its always good to see people fixing their own stuff rather than pay an arm and a leg.
Thank you for this useful video. I just finished replacing my noisy bearing on an LG WM2501HVA Direct Drive washer. Your video was very helpful, and you made it look easy.
Some challenges I ran into, that will hopefully help others, include:
1) Driving the old bearings out was very hard, so hard that I bent a drift punch, and when they finally cut loose I accidentally scored the bearing race. I cleaned this up with a small Swiss pattern file and steel wool. If I had to do this again, I would not pound the bearings out, I would use a bearing puller. I was told that many people crack their washer tub when doing this. That could be a costly accident (~$300). I am surprised I did not crack mine. I used penetrating oil and even so it took a long time to get the old bearings out. Worth using a bearing puller next time.
2) I kept track of all the different screws using a box with many different compartments, and even so, it was not easy. Next time I would put them in plastic bags with Post-It notes.
3) I used the old bearings with a piece of wood and a rubber mallet to drive the new bearings in. Worked like a charm.
4) When pushing the inner washer drum (metal) back into the rear bearing, mine did not fully seat. I noticed this when I was putting on the stator, the splined shaft did not stick out enough. This was a drag since I had reassembled a lot of the washer at this point. I threaded the 17mm head bolt back into the shaft, without the rear magnet part of the stator, and then carefully leveraged the shaft to fully seat using a large screwdriver and piece of wood to pad. This worked out fine and allowed the shaft to protrude enough to install the stator as in the video. So, in the video around 20:07, Matt pushes down on the washer with body weight, I pushed down but did not fully seat the shaft.
5) The gasket seal was a pain. Mine had residue and mineral deposits on it. I carefully cleaned it in the sink and put a very light coating of liquid soap in the groove that needs to slide over the plastic. The rear spring was hard to install. I used Vice Grips as in the video, and as expected, broke the connection on the end of the spring. Went to the local hardware store and bought a replacement spring that was no so brittle and little bit lower spring constant. That worked easily.
6) I put the front gasket on, before the tub weights (thanks for the tips on here on doing that, that made it much easier)
7) When I had the tub out, replacing the bearings, some plastic hemisphere parts associated with the water inlet ports, fell off. This concerned me at first, but they slip right in and the water hoses hold them in.
If you are replacing a noisy bearing, I recommend ordering both bearings, the bearing seal, and the tub seal, and the front gasket springs (hoops). Buy, rent, or borrow a bearing puller.
Appliance Parts Pros were great, not only in this video but when I called to ask some questions.
I should have read your comments before I did mine. I hit most of these issues. When I installed the shaft and it did not protrude enough I did the following: cut a small piece of 1X4 and drilled a 1 inch whole through it. Then I put that over the shaft and then threaded the 17mm bolt in an tightened this against the wood. This seated the shaft enough to install the stator.
@@BruceGuitarLessons Very helpful and creative!!! I may face such a situation when I will work on my Washing Machine.
Our LG WM2101HW washer sounded like a freight train the last few weeks. I watched this video and wrote down 2 pages of step by step instructions. The video showed exactly how to do the job and I could not have done this project without it. Took me 5 hours start to finish. A couple tips I've read (and used). (1) I used a piece of rebar to punch out the old bearings. (2) I used the old bearings as the go between to hammer in the new bearings. (3) Had a little difficulty getting the inner tub shaft to seat all the way but after taking out/re-inserting the rubber bearing seal it seated perfectly (3) Definitely put the inner tub gasket wire on before you install the weights. (4) Installing the outer gasket wire was the hardest part so I saved it for the very last step. (5) Give yourself plenty of room to do the job - move the washer to the garage.
How did we do? New washing machine - $599. Appliance repairman estimate to replace the bearings - $500. Did it myself for less than $50 in parts. Back in place the washer runs like a dream. My wife is very proud and appreciative - priceless!!
Awesome guide! One word of advice if you can’t pound out the shaft. I know I couldn’t and actually broke 2 2x4s using a 3 pound sledge hammer.
Take a throw away bolt and thread into the shaft. Then drop it so that the bolt strikes the ground. If you to protect your cement, do it on a landscape block or steel sheet. The shock of it striking broke it free for me after the second drop from around waist high. The rest was cake, including punching out the bearings. For the new bearings, put them in the freezer for a few hours to cause shrinkage. They will also seat easier.
Hope that will work for me. I can't get the shaft out for love or money!
@@Donnie_Prestwood Did you manage it eventually>
I used this site to replace the bearings and seal. the information and instruction is spot on. The only place I had difficulty was installing the rubber hood with the counter weights installed. I removed the weights and was able to get the rubber boot on with ample room for the fingers to get it over the lip. After that I installed the weights and finished up the job. Seems to be working great and no need to wear hearing protection when the washer is running. Thanks
Thank you so very much for making this video. This was a very lengthy installation although simple by nature, so tedious I don't see how I could have done it without this video. I am sure this save me hours upon hours of time. This guy knows what he is doing too. Which helps. He's kind of like a Bob Ross for appliances.
Excellent how-to video. I'm a general contractor and very skilled with tools, following this video took me around 4 hours start to finish, which included a thorough cleaning of all the parts, including the spider, both tubs, and the door seal. I pressure washed everything, and used a screwdriver and a wire brush and CLR around the spider. Amazing how dirty everything was. My only regret is that I didn't also change the spider. Mine is still good, but corrosion is starting around the edges, and at $60 I think it's worth doing while you're in there.
+Averell Eshaghian Glad you got the washer fixed!
Just finished replacing the bearings on my LG WM2277HS. Followed the directions step by step which made this tedious job bearable. It took me a long long time because I did it by myself and I am 70 years old so I work slow. Only change I would make to the entire video is that I would attach the weights AFTER I attached the seal to the tub. Makes that seal a lot easier to work in the groove. Other than that, fantastic video. Thanks.
Thanks for the tip! Awesome job on getting the washer fixed!
That's is AWESOME! And thank you for the tip!
Thanks for the tip. It made it a lot easier.
Edgar Allen are u still alive
Thank you. Thank you. Thank you. We watch this video, ordered the parts and repaired the washer. I don't believe we could have completed a repair so intense without your video. It took us around 6 hours but we saved buying a new washer. We went ahead a replaced the pump while we had the washer apart. Your tips were great. We knew to order the tub seal. We wouldn't have known without your help. Again, Thank you. You guys rock!!!
You're welcome! Glad we could help.
Thank you guys so much for the video, it helped me out a lot. Im sure I could have done it without this video but there would be a few steps I might question. You guys did a great job with the video including the camera angles, and the short clip of each bolt you tightened. Unfortunately we waited to long to replace the bearing and it got so bad we had to replace the spider arm also, with that being said we had about $175 in repairs, including both bearings and seal, as well as spider arm and outer plastic tub seal. All parts I bought from yours website because you made such a great video!
Thank you for the thorough video! Appliance Parts Pro also has a hotline which proved to be very helpful.
I just completed the repair successfully on my 12 year old LG washer. My biggest piece of advice is to change out the gasket and the discharge pump while you are doing the bearings. ~$100 worth of parts and you will have a machine that is close to new.
I have the following detailed notes and tips based on how my repair went:
1. The step to remote the inner (metal) tub from the outer (plastic) tub was much more difficult that the video suggests because I did not use the suggested rust buster. I sprayed WD40 liberally, broke 2 pieces of wood in my attempt to dislodge, and moved from a hammer to a sledge hammer. The piece would not move at all. I called Appliance Parts Pro and they were very helpful in suggesting I do not use WD40 but use a rust buster (they suggested Mars Rust Buster). My local Home Depot and Lowes did not carry Rust Buster so I used a product called "Blaster" from Home Depot. I sprayed Blaster and let it penetrate over night. The pieces came apart the following morning.
2. The step to remove the bearings took much longer as well. I tried using tools I had as a makeshift punch but these were ineffective. I ended up buying a 6" punch which eventually worked. Even with the new punch, it took me lots of effort to dislodge the bearings.
3. Someone in a previous post suggested using a cupcake tray to keep track of the screws, which was very helpful. I used a egg carton and made notes on which screws were in each compartment This turned out to be extremely helpful during reassembly.
4. The locking pins on the shock absorbers were difficult to remove. I tried the technique in the video to use a socket, but this did not provide enough pressure on the tab. I was able to free the locking pins by using a needle nose vice grip locked on the back side to press down the tab while I pulled the other end with a larger vice grip.
Take your time and follow the video and you will be successful.
Oh thanks, I have Blaster from this summer's work on the lawnmower. Would have never thought of that!
All done. About $65 in parts + great video + about three hours on a weekend I was able to silence a pair of very loud and soon to fail bearings.
- I found a little bit easier to install the gasket on the tub before putting the weights back on during assembly. Just a little more room to move around.
Hi Paul! $65 eh? So I guess you did not buy from AppliancePartsPro. The bearings could have been found on Amazon. Look for KBC bearings 6306U and 6305Z at a fraction of the price
Spider assembly was good?
@@davidhinson29 How did you find the the compatible bearings for KBC? I can't find sizes of the MAP61913708 (original LG PN) anywhere.
This video was so helpful. We bought the bearings, seal, and spider assembly from appliancepartspros for our 11-year old LG Trom. We had two bad bearings and the washer sounded like a rocket engine when it went into it's spin cycle. Took me about 2 hours to get all the way to the bearing removal. I pounded on the tub axle with a 2 lb. mallet with no joy. Then I put some WD40 and a heat gun on it for a few minutes and pounded it out without too much difficulty. Used a 3/4" Socket extension to tap in the new bearings.
With the new bearings the machine runs like a champ and is supper quiet. Thanks appliancepartpros for the great video. Maybe I'll get another 10 years out of my Washing Machine.
+Gary Fluitt Glad the video helped you get the washer fixed up!
GREAT DETAILED VIDEO. BUT OF COURSE IT DOESN'T ALWAYS GO THAT SMOOTH, EXPECT TO RUN INTO MINOR HASSLES AND HAVE SOME KNOWLEDGE AND EXTRA TOOLS TO COMPLETE THE JOB. DIY SAVED ME A LOT OF MONEY AND THE WIFE THINKS I'M A GENIUS!!!!
Excellent, straight-forward instruction on what would otherwise be a rather intimidating repair. Good to know what to expect, without glossing over some of the more difficult aspects. The socket and wrench tip for pulling the shock pins was brilliant, and very helpful. Thanks a bunch!
I followed your instruction to the T and it worked perfectly!!!! Thank you. Great video!!!!
A message to every one USE A BREAK FREE SPRAY just like he says to loosen those bearings!!! Let it set for a while and beat them out!!!!
Awesome, glad the video helped get the washer up and running!
This is why I read all the comments of the viewers - thanks a lot!
This fix took about 6 hrs and I have mechanical experience. The hardest parts are getting the bearings out and getting the tub gasket springs back in. I had nothing else to do on a workday and thought let's try and save some money. Basically paid myself $600-900 dollars.
I would definitely leave the tub gasket on because no BS it is a pain to get the spring back on. Everything in the video is spot on and had to watch it a few times.
We just finished this repair on our LG Tromm WM0642HW. Wow, you make it look easy. It took two of us and entire Saturday to get it done. Our drive was pretty stuck in the bearings and our bearings broke apart when pounding them out. Now that it's all put back together it is much quieter, still a little squeak and knocking on heavy loads, but hopefully this repair will give us at least another year with this washer. Thanks!
I've got the exact same washer and it's making an unpleasant noise during spin cycle, and I assume it's a bearing as that is what is sounds like. How has your repair held up? Did the squeaking and knocking go away?
Amanda Brighton
AppliancePartsPros
I am unable to take the drum apart by hitting the shaft of the spider that comes through the bearing. I am afraid that heavy strikes might break the spyder. Any suggestions
How did you manage to get he drive loose....I’m having a hard time.....it’s not even moving a bit....I have been hitting it for like 50 times
@@betin197610 yikes with these roadblocks maybe i'll just ride it out. thats a showstopper if you can't remove the bearing. mine just shakes violently on high no squeaking
Beto Comales did you get it loose yet ? I’ve been wackin this thing for a week . What did you do ?
This video is invaluable and saved me hundreds of dollars. I didn't have to buy a new washer or hire a repairman. All it took was $35 in parts, time and effort (and a lot of patience on my wife's part). I couldn't have done it without you. You may want to take it a little slower and show some more detail. There are a few tricky parts for a first timer that I'm sure is old hat for an experienced repairman like yourself.
Well, what can i say, What an enjoyable video, felt like i'd had an hour at the movies, i do a few washer repairs but i was totally lost in that video,it was excellent in both sound and the camera work, putting the camera inside the works under the tub,good tip using the socket to hold the locking tab in,well done to all involved,looking forward to more of the same......
+Ray Andrew Glad you enjoyed the video, hope it helped you get the washer fixed!
Ray Andrew مز
Thanks, Matt & Appliance Parts Pros!
First that parts ordered arrived on time and I never question if they are genuine LG.
This was not 'a very easy repair' but one that was worth it.
Directions are top notch, very detailed.
Many thanks for posting this.
Glad to help!
this technician is so outstanding. I wish I could help him and learn from. good job maestro. 5 stars rating for me
Glad the video helped you get the washer up and running!
Excellent instruction. Changed the bearings, spider and boot. Only thing was the new boot was so stiff, after fighting with it for about a half hour I decided to pull the weights back off. After that it gave me fingers more room to work and got the new boot on relatively easy, then reinstalled the weights. Thank you so much, this video is a definite money saver.
Pro tip: Place the bearings in a hefty bag and put in the freezer overnight. The cold temp will cause the bearings to contract and make installing much easier.
How do you clean the stator and rotor if they look like the ones in the video?
@@Xclusive615 take the rotor and stator apart and carefully vacuum both parts with a plastic attachment. Clean the stubborn particles with a moist rag.
Thank you sir. Worked like a charm. In none of the vidoes did I see anyone address cleaning the rust/crud on any of the parts. A little time consuming but was able to them all clean. Thank you!
Thank you! I have a 10 years old LG washer that made grinding noise until it stop spinning totally. While I was waiting for a delivery on a new washer next week. I decided to give it a try, followed you step by step to fix it! Then I did it! The only problem I had was getting the stainless steel drum out from those 2 bearings. It took me 2 full days. It just won’t let go. 😩 But I did it! You saved me spend money for a new washer. 🙏
Excellent video, great camera angles and it was nice to hear the socket sizes
I had the problem with the loud grinding during the spin cycle. However, I believe the bearings finally gave out completely and we were getting an "LE" error as the drum would not spin at all. I watched this video which was incredibly well done. While I am fairly handy with doing my own repairs, I have elected to have an appliance repairman do this. It is good to at least understand what is going to be pursued. Hopefully the bearings are the only problem and we can extend the life of this 13-year old unit a bit longer. Thank you for the excellent repair video.
You're welcome!
Thanks for this! This was a fortune-saver. Only took 7 hours!!
As with others, THANK YOU! While my repair took 6 hours over several days, my washer is running like brand new again. Disassembly was easy and I was feeling pretty confident. Then it was time for the inner drum shaft. I let my washer run on junk bearings for probably a year so I assume those things were fused to the shaft. After several hours of broken wood and pounding with a rubber mallet, I had no choice but to switch to a 4 lb. sludge hammer. I protected the shaft as best I could and it eventually let loose. The bearings were hammered out again with my sludge hammer and the largest sockets and socket extension I could find.
Upon reassembly, I realized I damaged the spider arm shaft with my 4 lb. sludge hammer as I couldn't get the rear cover on the stater. I had to order a new spider arm as a result. I actually put the door gasket on before even starting the re-installation of the tub. Everything else was cake after that.
Amazing video. I feel comfortable attempting this now. By the way you left the top sheet metal screw out of the drain hose/filter housing. It goes right above where the hose clips into place. Great job though. You guys are real pros.
J. Bingham Glad the video helped you try the repair!
Washing machine of 9 years starts making funny sound. Tub can only turn a little bit. Call LG to see if Direct Drive warranty will cover it. Licensed LG tech comes over, looks at it, says its a $300 part + $500 in labor to fix and buy a new washer. I google some more and find this website. Start taking apart the washing machine to do this, and find the rotor in the back with plastic teeth has worn out while doing the disassembly. Bearings look great. Buy replacement rotor with magnet wheel for $40 delivered and machine is good as new. Thank you for posting such a wonderful and informative video! I wrote a complaint to LG saying that the LG tech is not representing your company faithfully.
That's great to hear! We're so glad that we could help you repair it instead of replacing it.
Great video. One suggestion, using the old bearings to press (hammer) in the new bearings eliminates potentially damaging the new bearing.
+Michael Smith Glad the video helped you out, thanks for the tip!
AppliancePartsPros .
Sort of like when I use my old brake pad with my c clamp to bring the piston back in.
I’m going to use threaded rod nuts and some wide washers.
I start by saying THANK YOU VERY MUCH! This was an amazing video. This was my first washer dis/reassembly. I had my wife stop the video at each step as I followed it to the "T" and I had no issues. My machine had a few minor variations, probably in design by year, but otherwise it was exactly the same. I did not have any extra screws/bolts left over. HAHA. I commend you on this tutorial. You did a great job explaining and showing each step both disassembly and reassembly. *VIEWER SUGGESTION: Remember to label all your screws and bolts as you take them out. Be ready to clean. This will help in reassembly.
You're very welcome! Glad to hear that we were able to help you out with your repair. And you are so right about the screws. It's easy to think you'll remember which is which until you need to.
5 Stars all the way. Great step by step video. replaced both bearings, seal and tub seal. $96.00 Can. in parts and a few hrs. for repair.
Thank you.
Ronald Trudel Glad you were able to get the washer fixed!
that prize is exactly equal to my advised prize to fit my aeg washing machine spinning-noise.
I did this bearing change a year ago and bought the seal and bearing from AppliancePartsPro.The bearing did not last long because I am doing it again. I think I will look for better bearing from a industrial bearing vender this time. Thank you for the vedio! Really helps in the process.
That does seem pretty soon, if it is under a year give us a call. Glad the video helped you out!
He's a Master of any of these Projects
I completly rebuilt my LG WM1832CW using this video and ordering parts from you. New bearings and seal, Rotor assembly, tub position sensor, tub seal, cold and hot water valves. My LG runs like it's new again thanks to you and some effort from myself. All for about 300 bucks! Much appreciate the time and effort tjat you spent on this video and your website. Your ordering system and parts diagrams are first class. Than you!
kronomarine Glad the video helped you get the washer fixed, thanks for the order!
Thank you for the instructions. A couple of hours and 25 dollars in parts the washer is fixed, getting the seals and retaining rings back on was the worst part for me.
One of the most outstanding and informative RUclips "How To" video I've ever used. It made the replacement of my drum bearings and seal a "No Guess" job!! 😁
over a million views !! We love our washers !!
Good catch, this is our first video to go over 1 million! I cannot imagine how many washers have been saved!
@@appliancepartspros Yes, Sir; your videos are extremely helpful. I have already used several of them during this pandemic.
This looked intimidating but we got through it. Now our 12 year old LG washer purrs like a kitten. Thank you so much for this in-depth video, we couldn't have done it without you.
good vid thanks but i would use the old bearing as a drift to protect the new bearing to tap into place
fentz fensom Thanks for the tip! Glad the video helped you get them changed.
fentz fensom is
fentz fensom - would this risk getting debris and/or grease into the new bearing and/or seal when you hammer on it???
AppliancePartsPros 1
I wish I would have read this before I replaced the bearings. Good idea.
This was an outstanding instructional video! Took me about 3-1/2 hours taking my time to ensure I didn’t miss anything. I agree with the other comments of installing seal prior to weights, but other than that this was perfect! My total cost for both bearings and the tub seal was about $25. Thank you!
You're welcome!
make sure when you put it back together u grease the bearing, seal lip, and basket drum shaft or it will squeal when u get it back together
Great tip/reminder. Thanks a lot. It is very important!
Thanks for the GREAT video. I did the bearings/bearing seal replacement today and it went smooth thanks to your video. It took me 3 hours with breaks to watch sections of the video as I worked. No leaks and no jet taking off sound any more.
Bob Singer Awesome, glad the video helped you get the washer fixed!
I would charge $400 to fix this. Thanks for the video but I must respectfully disagree that this is a really easy repair! You have amazing skill!
+Carlos Garcia There is no real skill involved with this. If you can turn a socket/screw driver and have upper body strength to lift and move, this is a pretty easy repair. Just takes multiple hours.
I must disagree, The average person has nowhere near the ability to complete this task. The person must have some mechanical background and/or knowledge to get it done.
This was a walk in the park.
LOL, I don't think it appears to be a very difficult task just, really time consuming and hope that you did put everything back together correctly. My real comment is, Fu(k you, LG for making such a common problem a real problem to fix.
@@matthewstachler7614 I need to replace the bearing in my LG washer. It's a job, but not impossible. I am going to take photos just to give me a reference if needed. Yes I'm somewhat taken back by the labor intensive job to fix this issue. Considering the cost to replace, or the cost to have a repairman do the work. Going to enjoy the task.
Great video. I followed it to the letter. The only 2 things I would add is that when you take the case out to be careful or put a piece of tape across the 2 bulbs that are in the water inlet hot and cold. One of these fell out while I was splitting the case and broke. I was able to repair it. Also, when putting the drum back into the lower 1/2 case to make sure to clean ANY corrosion. My shaft didn't seat fully and I had a heck of a time getting it out the back (with the entire assembly back in the machine)! Thanks for putting up the video, it saved me from having to buy a new washer.
You're welcome! And thanks for those tips.
HI! Your vidéo helped very well me to change bearings and other spares on my washing machine LG. Good tutorial!!! many thanks from France!!! ;)
+Scrumper66 Glad the video helped you get the washer fixed!
Excellent step by step video. Only difficult part was getting the old bearings out which were fused to the shaft. Have some patience and let the penetrating oil do its thing. Thanks for allowing me to save our washer from the landfill.
Awesome, glad the video helped you get the washer fixed!
thank you so much this helped my family save lots of money
+John Thrush Awesome, glad the video helped you fix the washer!
Just finished replacing the ball bearings and the tub gasket on my 14 years old LG. Without your video, I would have to buy a new washer! One thing I want to add to your instruction is when to insert the new bearings, it's much easier to use the old bearings to drive the new bearings in (stack them up and hammer on the old ones).
Glad you were able to complete your repair. If there is anything we can help you with in the future please let us know.
Yeah I’m just gonna buy a new washer lol. Good detailed video though.
People like you are great for business 😉
I find jobs like this easy to follow and do. If everybody did, there'd be no business for repair centers and manufacturers
@@truth.speaker I think you’re right. I was with him the first 4-5 steps. After that I’m gonna start losing parts especially with small kids around in a little space lol. Normally I wouldn’t mind taking on a challenge but this dude is taking the whole thing apart and there is always that one screw in my experience that won’t go back in.
@@truth.speaker here’s a tip for any job like this: get a muffin tin (or two) to hold the screws. If you group the screws by each section you are working on and place the in order in the muffin tin, then it’s easy to go backwards when you are putting it all back together.
@@jeffcushing6016 good idea 🙂
This process takes a while and there were a couple areas that were tough (banging out the drum from the outer tub and replacing one of the spring clamps) but this video is excellent in terms of explaining step by step. I got the parts for about $25 and it saved me from buying a new washer.
Changed bearings on front load duet wirlpool. Changed nothing, washer walls away on spin. ? Bent shelf on basket?
Use the old bearing to place the new bearing in also liquid detergent the cause of the rusted bearing 🤷♂️💨💨🏌️😂✊
Thanks for the tip and explanation.
Thank you!!!! We have been working ALL day trying to get the front loader apart, cleaned, and put back together, when I finally did a youtube search.The video my husband was following was less than clear (and it wasn't in HD either). Luckily the spider arms (? is that what it's called) was just filled with gunk and not corroded (too badly). We mainly took the washer apart because the bearings. What a pain it was getting it out, but I didn't see this video until after we had it 1/2 way completed. Hubby couldn't get the bearing back in - so I took over. Thanks to your video, it went in, and I got the drum put back together. I took the weights off the front - since it was SO heavy to get it out. I also took the wire coil looking thing off the back so when it gets put back in it will be (hopefully) lighter. I am going to watch this a few more times so I get comfortable with the process. Although you are working on an LG washer, the Samsung washer (WF350ANR/XAA) we have is very similar. I am noticing that we don't have as many bolts (not missing - Samsung apparently didn't feel it necessary to provide all of the bolts that there were places to be bolted - namely the front weights). Anyway, I really appreciate this video and in the future, if we have any more appliance repairs, yours is the first shop I will check out for parts. THANK YOU!!!!
The Bearings where fine. The spider was the problem.
Since I am selling this machine anyway, I also only replaced the spider. The bearing set was 80 for 2 bearings and the seal. If its not broken, im not fixing. I thought about it for a while, believe me. But it came down to the fact that Im not selling a broken washer. I will fix it and sell it. I dont know how long those bearings will hold. Maybe a year, maybe 5 years? I couldnt justify replacing them since they were not broken and in perfect functioning condition.
Great detail. One of the best step by step I’ve seen. Worked great for me. It took me a few hours to do. Some tips for people. Penetrating oil is a must to get bearings out. Buy a punch set to knock out and put in bearings.
The front grey gasket I would put it on with the metal spring clamp before installing the two weights. Having weights off makes it more accessible. Metal spring reinstall was a major pain. It didn’t want to stretch.
After you install the lower drain pour some water in before installing door so you can check for leaks. Makes checking so much easier. Mine leaked and was a pain to access leak location. Why the designers didn’t make a longer spigot for the rubber boot to slide in seems a design shortfall.
Take pictures with a cell phone to jog memory. Reinstall screws as you disconnect or use a muffin pan to keep in order. Video is so good a novice can follow it with confidence. Excellent production of it.
Great tip - very useful. Thanks for sharing your experience.
hetouahta htneuohtnueo, I cannot respond to you as you have the reply feature off. How the seal sits could vary from brand to brand. Just like you did it is important to make sure the seal is seated all the way down and even so you get a good seal.
+AppliancePartsPros Thanks for the heads-up. I re-checked my photograph of the original seal and I can't tell how deep it's seated. It's definitely recessed a bit, but I can't tell if it's bottomed out or not.
I did a couple test fits with some grease on the shaft and did some measurements to see where the seal was riding. If I install the seal flush, its protruding outer lip rides up off the machined surface of the shaft. If I fully seat it, then it rides about 1/8" away and the outer sealing lip is almost falling off the edge of the shaft.
Basically it looks like the seal has to be seated so the protruding lip is flush, but the OD of the seal itself has to be recessed about 1/16" or else it doesn't sit on the shaft correctly when the drum is installed. The only way I can see to install it straight is to use a caliper to check the circumference, because it's floating in the bore and not referenced against anything easy.
This is pretty bizarre and seems much more tricky than I've been led to believe, but it does seem that the seal isn't supposed to be flush or be driven all the way in on this model. Have you ever seen this on Samsung washers?
AppliancePartsPros LGSHOCK
LG SHOCK ABSURD
+Lisa Esparza q
AppliancePartsPros
I am unable to take the drum apart by hitting the shaft of the spider that comes through the bearing. I am afraid that heavy strikes might break the spyder. Any suggestions
NK buy a new spider. That’s what I did so I didn’t have to worry about that.
I just wanted to say thank you for the helpful and informative video. It gave me the confidence to fix the bearing issue with my 5 year old LG washer. Although my washer is a different model than the one used in the video, it still gave me the overall view on “How To” approach the repair and what items and materials were required. The only thing that I would highly recommend is that the spider, although it may appear to be good, should to be replaced. It is one of the backbones of the whole process. It is worth your while to find the full assemblies rather than trying to piece meal the repair parts. It may cost a little more but in the long run it will save you hours of time and frustration.
Great video. I could not get the smaller bearing out. No matter what I tried it would not budge. I tried that rust remover stuff several times even waited overnight. Ended up sending back all the replacements parts and just ordering the tub with the bearings and seal installed. The rest was just following the video to finish up, Quite happy. The tub was about $150 with bearings and seals. My outer bearing was pretty much all destroyed when I opened it. It was giving me warnings for several weeks. When you hear that grinding noise don't let it go. Otherwise the penetrating rust will get you in the end.
Glad the video helped you get the washer fixed!
Thanks, this video was easy to follow. I too, had a hard time getting the bearings out. My husband ended up taking it to an auto shop to get hammered out. After putting new bearings in and getting it all back together. The machine ran one time without issues. Then the knocking came back. It ended up the shaft on the spider did not fit well inside the bearings. It must have malformed. I ended up buying a new spider and the back side of the tub with the bearings and seal already in place. Works good now. I recommend buying the spider, the back of the tub and a tub seal to do this job.
Glad we could help! Thanks for the tip.
Great video; well organized, all steps are clear and concise. I have a Samsung front loader new in 2009. Inner drum won't turn even with power off. Debris in filter, which, after watching your video, I can see is parts of a deteriorating spider, which is probably what is jamming and keeping the drum from turning. I highly suspect that overloading was the cause of the failure. I just now received the service manual, which I will check for hidden "gotchas', before I follow your video to disassemble, confirm the failure cause, discover bad parts, and order them. Thank you so very, very, much !!!! Great job
+divingfe Awesome, glad the video is helping you get the washer fixed!
Just got done replacing my bearings and tub seal. I attached the weights after the liner was installed. I knew that would make it much easier. I used my old bearing as a drift when I installed the inner bearing. Other than that, pretty straight forward video. A tip for anyone trying to knock out seized up bearings. Put some rust dissolving solution on there and let it sit a few hours. I used METAL RESCUE GEL. It dissolved the rust on my inner bearing and allowed me to knock it out after sitting about 3 hours with the solution completely covering the bearing.
Firstly, I want to thank you and crew for your informative video. In replacing the bearings in a LG Model WM2501HWA, I found that the spindle had ~1/4" rough section which prevented the spindle from inserting completely into the new bearings - poor QA by LG. After hand-sanding this down, the spindle slid smoothly into the new bearings. This also helps explain why the spindle was so difficult to remove in the first place.
You're welcome! I'm glad the video was helpful. Thanks for letting us know how the repair went for you.
Thank You. Your video couldn't be easier to follow and it helped me fix my washing machine! Saved me a ton of money!
My spider was severed on two of the three arms. It caused the tub to wear into the plastic (burning smell) and found some plastic shavings in the wash. Wasn't sure if bearings or seal were bad, but replaced them anyway as I don't want to do this fix again.
Took 4 hours, and one hour was just swapping the bearings (had to use an air hammer after pounding on it with a regular hammer unsuccessfully). I could've spent some more time if I wanted to thoroughly clean all the parts but it was getting late and I just wanted to be done.
Thanks again!
+Mark Olchanowski Awesome, glad the video helped you get the washer all fixed up!
Thanks for the excellent video. Just completed this bearing replacement and had no problems. Still pissed at LG for a crappy bearings that failed after only 2 years, but all is well now. I did upgrade to double sided sealed bearings hoping they will last longer. $50 in parts and a few hours of time saved a $600 repair.
+AJ Catalanotte Glad the video helped you get the washer fixed!
Another successful bearing replacement with the help of your video. Much appreciated. I estimated 2 hours for the job. It took 6 including a test. Key time consuming parts were bashing out the drum shaft, followed with bashing out the old bearings. Inserting the new bearings was also a challenge due to the very tight fit. The result is great. Prior to the change the noise generated was >110 dBA within the laundry on spin cycle (using a non-calibrated Android app) - about the sound level of a petrol chainsaw! Post fix, a sublime 90dBA.
That's great to hear! We're so glad we could help you get that noisy washer running quiet again.
I'm seeking further advice, please. While changing the bearings has eliminated that particular problem and noise, a new noise has developed since reassembly. It sounds like the drum is scraping something. I'm quite sure it wasn't there before the bearing change. The scenarios are: A. only with a slightly unbalanced load, such as a single towel, and B. A heavy load of washing. I'm reluctant to pull the whole thing apart again without some remedial action to perform. What are your suggestions, please? Thanks
A public service for the novices (like me...) check ALL the dimensions of ALL bearings before replacing! It became a crisis when a new noise developed. On investigation, starting with taking the motor apart, I noticed fragments of magnet on the rotor. Removing the shaft bolt, although I had used a thread sealant (Loctite), the shaft bolt was a bit loose! The shaft worked slightly loose causing the rotor magnets to scrape on the stator coils. Then I noticed the inside diameter of the outside bearing was not tight around the shaft. The parts supplier sold me an incorrect rear bearing that looked right (OD & width correct) but I failed to note that the inside diameter was 30mm (like the front bearing) but it had to be 25mm! So while the machine initially reassembled ok and passed all the tests, it was doomed to fail again. After replacing the incorrect bearing and reassembling, tightening the bolt required a lot of force until I heard a "pop" probably by the shaft and bearings seating correctly. All is now well, and running as it should. The damage to the magnet was minor- about the size of a pea broke off, causing no adverse effects. I took great care to remove all magnetic fragments and dust.
Fantastic video. I was having trouble with my LG WM2016CW. The tub had play in it and I was getting a burning odor and smoke from the tub. The bearings and seal were like new, the spider was broke on all three sides. I also replaced the tub boot with this repair. The machine looks and runs like new. Thanks again for the video. Keep them coming.
+Rick Smylie Glad the video helped you get the washer up and running!
I've done alot of repairs and maintenance over the years, with the help of youtube, and I have to say this is the best quality video I've ever used. Great instructions, took your time, just well done. I'm half way thought this video, as the tub is still sitting in my garage waiting to hammer out the spindle when I get home. Hoping it works after putting penetrating oil on it last night. We'll see. Again, thank you. Great job.
Thank you so much. I was able to do this on my own it just a few hours thanks to your detailed instructions.
I would like to reemphasize some tips:
1. Don't remove the metal ring from the inner tube seal at all, there is no need to remove the rubber gasket completely.
2. That punch tool is essential to get things moving, both out and in.
3. Use the old bearings to get the new ones in without damaging them.
4. There is a kit on Amazon with both bearings, rubber seal and huge tub seal o ring thingy for the 2 white halves for $35.
5. Change the spider while you're at it. Mine was intact but heavily corroded and absolutely filthy and stinky. A replacement was $80 on Amazon and it took just a few extra minutes to swap it out. This will help the smell immensely and also help me get at least another 10 years out of my washer given that bearings are new as well.
I was wondering what happened to this repair guy saying his spider arm was corroded and needed replaced as well. We just bought a second hand Kenmore Elite H3 t and it was shut for awhile while a home was sold, so it's a bit smelly. Likely from having the door closed and such. If we do this repair ouselves, we'll defo keep an eye on the spider arm as well. Why would it be really smelly?
After waiting over a month for the repair company to come back with parts I decided to take this project on. Excellent instructions, only had trouble putting the outside spring back in place. The tool would have been most useful but could not see spending money on what I hope is only one repair.
The special tool are expensive, that is why we show how to do it with regular tools whenever possible. Glad you were able to get the washer fixed up!
This video was very helpful, and AppliancePartsPro shipped the reasonably-priced OEM LG parts quickly. Hope my repair lasts longer than the original 3 years on this machine.
A suggestion: reinstall the big front seal BEFORE you put the weights back on- it's MUCH easier this way!
Thomas Wright Thanks for the tip! Glad the video helped you get the washer running!
Great video. You did a good job with the recording and step by step instructions. I did my 2 bearings and a seal in 4 hours. But two things. You do not need to remove the bellows from the tub. Don't use a chisel to install the bearings. Thank you for a great instructional video.
Yeah, I think he used a long extention but they have a bearing extraction and installation tool.
Great video! I had a repair quote of over $1,000 to repair ours. I did it myself for about $150 (including the front outer tub, gasket, bearing set, and spider!). I have some tips to share:
TIP #1: Pounding the shaft out of the bearings (15:36) was near impossible, even after a day soaking in PB Blaster. If you know you're going to replace the spider anyway, forego the wood and just pound at the shaft. Or, to protect the shaft, you could screw a sacrificial bolt into the shaft and hammer on that.
TIP #2: if you replace the front outer tub, check for an extra hose outlet in the front-bottom (where the lower weight attaches). For my washing machine model (LG WM2077CW), the front outer tub did not have the outlet (as also seen in this video at 7:07). The new one did (like this www.rcappliancepartsimages.com/dbImages/00005679/01800759.jpg). Everything else was identical. I ended up having to saw off the hose outlet and glue a plug into it!
TIP #3: Don't let frustration get the better of you when pounding at the shaft and bearings (15:36 an 17:34). Upgrading to a mini-sledge hammer and crowbar could result in the tub gasket lip to break! I speak from experience. Fortunately it was repairable.
Thanks for the tips!
Thank you for doing this on a "dirty" machine! I saw how dirty my rotor and stator were and was planning on replacing them too, but the ones in your video look as bad as mine so I'll just change the bearings and seal. Thanks!
Thanks for posting this video.....it was VERY helpful and very detailed. A few things were different on my LG but otherwise this saved me a lot of money as I was quoted $400-$600 to replace the bearing. It cost me $50 for the bearings, shaft seal and small tub seal, 4 hours later it's working great. The only advice I can give is to install the grey rubber door seal before installing the counter weights as it's easier because the weights are in the way. Again......great video......thanks!!!
Awesome, glad the video helped you get the washer fixed up!
Excellent video. Following your instructions helped me get the job done. It's been 4 months and still quiet as a mouse. My old bearing was fused to the spindle shaft had to cut it off with a dremel but other than that the job went smooth. Thanks for the tips!
Glad the video helped you get the washer up and running!
Great video! I watched several others but this one used the same parts that I needed to replace. I agree with several others, put the boot on before re-installing the weights. I also labeled the top weight with a sharpie because mine is grey and the bottom is black. I bagged all screws and bolts as I was going and it made my life so much easier. I decided that since I needed to disassemble to whole thing that I would replace the boot at the same time, so I bought new one and a new outer spring because my old one was pretty rusted. I'm glad I replaced it because the old one was nasty, even thought it was functional. I would suggest that anyone who attempts this also purchase a new gasket for the out tub and replace that at the same time. I didn't because I didn't know to and I'm not having any leaking but if I was to do this over again, I would replace the gasket. The spider on my machine was in great shape, it did have some rust and mineral build up on it, so I cleaned it with CLR spray, scrubbed it with a nylon brush, and then washed it off with water using a hose. The CLR really cleaned it up. (Don't use CLR on plastic) I'd also suggest that if you have a shop vac, keep it handy. A couple of times water came out of hoses that I wasn't expecting. I did this repair in my garage so it wasn't a big deal but it was nice to have the vac to clean up the water. And I used it to vacuum up as much stuff in the machine as I could.
Thanks for your feedback and for the additional tips!
Fantastic video. Seriously, this is the second time I have to repair washer on unrelated issues, and these videos gave me the best method, seriously... method, to do a proper repair. Thank you Appliance Parts Pros.
You're welcome!
One of the best videos on installing bearings and seal. You have really saved my family a lot 💰 I will definitely be following you videos. Thank YOU!!!
just finished doing this using these instructions. the only thing different was a small screw on the front panel and few wires here and there. hardest part was getting the old crap bearing out. Thank you so much for everything in this video. Took me about 5 hours just because of the stupid bearing.
David Peters Awesome, glad you were able to get the washer fixed!
My original Amana Top loader from 1996 has an issue.
There is an oil drip on the end of the transmission.
When I moved the machine there were oil drops under it.
I'm planning to repair it, so far I have the pulley, new belt, and other parts, but
I don't want to put it back together if the transmission is leaking oil.
It hasn't be run in 5 years, so I don't remember the bearings making any squeaking or grinding noises.
Video made a lengthy repair straight forward. Thank you! Three suggestions: (1) use the old bearings to pound out the new bearings, (2) if the shaft won't go through the new second bearing without pounding (as happened to me), then install the rotor bolt with washer a few threads deep, block-up under the washer, and tighten to safely pull the shaft through. Repeat with thicker blocking until fully pulled. (3) install the door boot to the tub before putting the tub back into the frame/cabinet. You'll have more room to maneuver. On a last note, it took me about 6 hours, but at least 2 hours was spent just cleaning. Since you are that far in, suggest also removing the spider and cleats inside the SS drum. Mine were really gunked up.
Thank you very much for your tips. I will keep this in mind when I will work on my Washing machine.
This video is awesome! I didn't replace the bearings. I just needed the spider arm. I spent $94 instead of buying a new one for $1050. Thank you!!!!
Great how-to! My bearing rusted and I guess expanded around the shaft so I had a really hard time getting both the shaft and the bearing out. I had to use a sledge hammer to get the shaft out. The wood I used to keep from damaging the shaft kept breaking so I used hard rubber but it wouldn't budge. I finally just hit the shaft straight on twice and it came out. Once that was out I had to use a large chisel to get the rusted bearing out. I put everything back together and tested the spin cycle several times and it's as quiet as it was before.
Awesome glad the video helped you get the washer up and running!
Very well done video. Bearings are always a hassle, but a couple days of penetrating oil and a metal rather than wood block (I used a hammer placed sideways) freed the spindle. Couldn't find a punch so bought a cheap ratchet extension and that worked just fine.
James Frentress Glad you got them swapped out!
Took me two days to complete this task. I'm sure is saved some change but this wasn't an easy job. I appreciate the very detailed step by step. Thanks
It's not the easiest repair we've filmed, but we're glad we could help!