Do you know of a valid replacement for the TDA2003V? I need one for my CB radio and no one stocks them any longer except ebay. Amazon has a ridiculous 15 dollar one available but its probably the same clone ones ebay is selling?.
@@johnantopina5531 if you use 10 volt , you cant give more than 10v to your amplifier otherwise your capasitor will blow up. Dont forget giving lower requirement voltage to amplifier means lower power , loudness and sound quality Using 10volt capacitor just make limit for your supply voltage. When this IC needs 12 volt , use more than 12v supply capasitor but we dont have this voltage on capasitors therefore we have to choose 16 volt capacitors. You can use higher voltage capasitors but this work is inffective and useless ; in fact you just lose and waste more money and space for it XD. Excuse me for my Weak English and goodluck
are you kidding ? with 12V input you never going to get 10 W output! and the heatsink attached is only good for 4W. 10W amplifier atleast need a 10W capable heatsink.
Do you know of a valid replacement for the TDA2003V? I need one for my CB radio and no one stocks them any longer except ebay. Amazon has a ridiculous 15 dollar one available but its probably the same clone ones ebay is selling?.
Acabei de conhecer seu canal, continue postando vídeos, são muito bons!! Parabéns! !
Top 10 Best Flyback Transformer
Sir , Is it Okay If I Use Ceramic Capaciotr 104 instead of Mylar Capacitor 104 . Please reply my comment . Tnx . Nice vedio .
Yes, you can use without any problem
Sir , Is it okay if I use capacitor "470 uf 10 volts instead of "470 uf 16 volts" ? Please reply sir , thank you
@@johnantopina5531 if you use 10 volt , you cant give more than 10v to your amplifier otherwise your capasitor will blow up.
Dont forget giving lower requirement voltage to amplifier means lower power , loudness and sound quality
Using 10volt capacitor just make limit for your supply voltage.
When this IC needs 12 volt , use more than 12v supply capasitor but we dont have this voltage on capasitors therefore we have to choose 16 volt capacitors.
You can use higher voltage capasitors but this work is inffective and useless ; in fact you just lose and waste more money and space for it XD.
Excuse me for my Weak English and goodluck
Onley baterry ??
Nuevo sub
What song?
Why didn't you put it up to maximum?
I have a TDA2002 , can I use it?
and power source 12v 3A transformer with bridge filter. I know about use of transformer
EasyWebSolution check its data sheet connections might be different from its
What is the Output frequency range
Where is scheme? How i know, how connect?
Good job..
Otpornik od 2,2 oma treba biti malo veci oko 3,5 oma
This in 12v ??? Amper???
+Patrol Drogowy
It's powered by battery
How many volts?
are you kidding ? with 12V input you never going to get 10 W output! and the heatsink attached is only good for 4W. 10W amplifier atleast need a 10W capable heatsink.
Bro I'm facing noise problem. How to remove it
Not working :-(
3:10 I wanted to let you know that printed circuit boards have already been invented.
Supply Ka voltage Kitna ha?
+Prasant Kar
12v dc
Tech Ideas
Thankx
Nice pic sir
+Dilip Rajbhar
Thank you
Whats the voltage of the amplifier?
The data sheet says the tda 2003 has a operating voltage of 6-12v
Because from the sound of that is not ten watts
Nice
Tda2003 gives maximum 5 watts at 8 ohm speaker on 18 volts
Amit Ghosh was about to comment that. Most people don't read the entire datasheet, specially maximum ratings
Ic 2003 ko check kaise kare multimeter se
How to add potentiometer?
DAN-MAR CANETA left pin to gnd and right to 3.5mm +wire and middle is ouptut signal
4558 ic ka Bass Banana hai
Đa n mạch cái nhạc gì cứ ác ác gô gâu dê dê bực cả mình
Diagram dedo
Cv 203 audio amp
How many v power supply
sabufu
shob fack
Sound is not clear
Probably you did something wrong, you should read the datashit.
I mean datasheet!
What is the supply voltage