How to wire an immersion heater WATER HEATER WIRING MCB CABLE SIZE and THERMOSTAT

#electrical #wiring #heater
Hi everyone this video is about immersion heater circuit .quite simple dedicated circuit 2.5 mm t&E cable from consumer unit to 20A DP switch and 2.5 flex heat resist cable to the thermostat of the immersion heater. Hope it helps .Stay safe and Please Subscribe
If you like what I do and want me to start Your project, shoot me an email: [e-mail]
with a short description of the work you would like me to do, location and mobile number.
I’ll try to answer as soon as I can.
I’m based in Medway in Kent and work in towns like Sevenoaks, Rochester, Sittingbourne, Tonbringe, Dartford,
What type of work can I undertake: Complete bathroom and kitchen refurbishments, incl. Kitchen installation, bathroom fittings, tiling, plastering, plumbing, electrical, painting, carpentry, etc.
Psssss. I’ll make a video of my work only if you want me to!
Any other business cooperation proposals such as advertising products etc.
[e-mail]

[@mikedemetriou4227]

Hi - thanks for that video - super clear and very helpful - exactly everything I needed to know!

[@gregkerslake2252]

just started my plumbing apprenticeship and found this to be hugely helpful. Thank you

[@Reapologist]

Love your channel man top stuff it's really helping me with studying, some books just don't make sense. Keep it up man you've earned a sub!

[@london_roubenl]

Absolutely brilliant, faultless video.

[@cyber_Dean]

Great video! If the immesrsion heater has two 3kw elements I guess you just repeat this process for the second?

[@gabeerlazem7798]

Great video thank you buddy 🙏

[@vezzosetto]

I love your videos!

[@BB-vj4tt]

Thank you sir 🙏.

[@kcomfortsystemshvac7060]

Nice video,,very informative,,,,,,I have litle question !, this example can you use to install split A/C ? As well ? How is the best methods ?

[@markcostello4937]

I have a 2/2.85kw immersion. Could I put a 3 pin plug on it . Then put it into a hive smart plug with a limit of 3kw?
After watching your video I'm guessing no .

[@johnboywalsh]

this is not a typical domestic circuit. You normally have sink and bath circuits on the one head.

[@bimiuk4051]

My water tank has this immersion as well but I fail to understand how my thermostat turns immersion on or off?
Or is it just a manual job for when I need it, will have to go to loft and flick the switch??

[@BAMBOOLOUNGE]

I use this switch to heat the water quicker, today the light has gone out. Does this mean that the fuse needs replacing?

[@rinnin]

Where would you put a timer? On the load side or supply-side? Thanks

[@wll6777]

I’m no expert but just managed to replaced my timer. What do you mean, the timer would be installed between supply (cylinder switch) and load( hot water cylinder)

[@ClockworkApe]

Could you please post a video how to wire the dual immersion switch (the sink/bath one). Not a single tip on this anywhere on the web and it's not straight forward.

[@daithi159]

I tried this, it was a shocking experience... Okay ill close the door behind me

[@TheSummersProject]

How would I wire up an thermostat to the element too?

[@wordimobi5765]

How do you put a timer on that?

[@qbuilders9271]

Stay save lol nice video but corona scam is behind

[@mohammadbinali6490]

If its 4500 wat 3phase how we wire it?

[@glynwilkinson4087]

Why use flex cable and not twin and earth?

[@courblimey8887]

Because it’s flexible and also more insulated

[@jojo260180]

Panie Janku , a po polsku da radę jakiś film ?

[@hichemrochedi4245]

Flex is not 3 core cable, it’s just twin and earth 2.5

[@geoffreyharvey1252]

Brown which is LIVE does NOT go to earth terminal