Glad I could help! Could I ask for your assistance in providing a google review for our company? g.page/prestigeofficesolutions/review?gm Will be greatly appreciated!
Dear, thanks for the video. I have a finisher for bizhub 808 and the output tray 2 does not sort the sheets that come out and they do not fit into a single stack. Any recomendación on what can cause?
many different reasons can cause this. Too many to list but either you need to reload software or there might be a mechanical issue with finisher causing it not to align the sheets. there are two arms at exit and i've seen them go bad in the past. could be an easy fix and also can be a long tedious fix. sometimes its worth buying a used finisher and be done with it.
Merci bcp je suis technicien konica et quand je suis arrivé les livreurs ont dit que « le système d’agrafage faisait du bruit c’est normal » alors qu’ils avait allumé la machine et laissé la barre en métal remonter totalement sans monter la partie plastique dessus
yes it can. i recommend you purchase the paper catch tray cover otherwise it will be messy when prints come out. reach out to us for pricing and avail.
Push the sense of fingers in while you're pairing the machine on way for the bracket to come down then open the front door to finish it stop it for going back up
Hai,i have removed my stapler unit from printer but still printout comes through inner tray and stuck at stapler unit joining section .Where can i change in printer settings if i removed my stapler unit from printer ?
you need to remove the inner transport unit. you can't run the machine with it if you don't have the finisher connected otherwise it will jam each time. Also, when you remove the transport unit you need to install a catch tray which im sure you don't have readily available. you will need to buy it otherwise you will have a mess when all the copies come out.
you will see 3 black plastic arms behind the metal bar. turn the machine off, use 1 or two hands to push all three of the arms in and power the machine on. hold the arms until the bar has come down several inches below finger and immediately open finisher door to stop the bar from raising. now install the tray
Hi, We all appreciate the videos, it's just some of us take the time to like and subscribe. I have a Q. I have a couple of silver screws that have come loose in front of tray 2. They are stuck in the tray riser guides- if that is what you call them. Two of them came out and looks to have come loose from the inside and jammed in the verticle guide. Thoughts? how would I take the panel off to investigate. Thank you
Thanks for the quick reply. After watching this again, Looks like I need to remove the finisher to get access to the back cavity where you had the trays storage during transportation.
Man, this video saved my bacon, you have no idea. Thank you so much!
Glad I could help!
Could I ask for your assistance in providing a google review for our company?
g.page/prestigeofficesolutions/review?gm
Will be greatly appreciated!
Dear, thanks for the video.
I have a finisher for bizhub 808 and the output tray 2 does not sort the sheets that come out and they do not fit into a single stack.
Any recomendación on what can cause?
many different reasons can cause this. Too many to list but either you need to reload software or there might be a mechanical issue with finisher causing it not to align the sheets. there are two arms at exit and i've seen them go bad in the past. could be an easy fix and also can be a long tedious fix. sometimes its worth buying a used finisher and be done with it.
How do I get the paper out of the top drawer?
Like printing machine counter
sorry, not sure i understand your question
Merci bcp je suis technicien konica et quand je suis arrivé les livreurs ont dit que « le système d’agrafage faisait du bruit c’est normal » alors qu’ils avait allumé la machine et laissé la barre en métal remonter totalement sans monter la partie plastique dessus
Glad to hear the video helped you
It's interesting keep it up
if I want complete set drum unit + developer tank so how is the process..??
Can this machine be used without the finisher? I like the coper but don't have room for the finisher???
yes it can. i recommend you purchase the paper catch tray cover otherwise it will be messy when prints come out. reach out to us for pricing and avail.
Push the sense of fingers in while you're pairing the machine on way for the bracket to come down then open the front door to finish it stop it for going back up
is it the same with a C759 model?
very similar
WHERE CAN I BUY SIMITRI HD TONER WITH SHIPPING TO CHILE?
Hai,i have removed my stapler unit from printer but still printout comes through inner tray and stuck at stapler unit joining section .Where can i change in printer settings if i removed my stapler unit from printer ?
you need to remove the inner transport unit. you can't run the machine with it if you don't have the finisher connected otherwise it will jam each time. Also, when you remove the transport unit you need to install a catch tray which im sure you don't have readily available. you will need to buy it otherwise you will have a mess when all the copies come out.
Hello, I would have such an unusual question, can the finisher fold leaflets?
no idea what a leaflet is. sorry
@@PrestigeOfficeSolutions It would be like a brochure.
What can I do if my machine bar has moved to the top without the tray on please
you will see 3 black plastic arms behind the metal bar. turn the machine off, use 1 or two hands to push all three of the arms in and power the machine on. hold the arms until the bar has come down several inches below finger and immediately open finisher door to stop the bar from raising. now install the tray
What is the model number for the stapler finisher unit?
Fs534. But could be similar models as well fa536 etc
Hi, We all appreciate the videos, it's just some of us take the time to like and subscribe. I have a Q. I have a couple of silver screws that have come loose in front of tray 2. They are stuck in the tray riser guides- if that is what you call them. Two of them came out and looks to have come loose from the inside and jammed in the verticle guide. Thoughts? how would I take the panel off to investigate. Thank you
I would have to physically see it not easy to describe over a chat.
Thanks for the quick reply. After watching this again, Looks like I need to remove the finisher to get access to the back cavity where you had the trays storage during transportation.
Used