How To Replace Front Axle Shaft 1998-2011 Ford Ranger
HTML-код
- Опубликовано: 12 сен 2024
- Buy Now!
New CV Axle Shaft from 1AAuto.com 1aau.to/ia/1AAX...
A front axle shaft has flexible joints. Often, these joints wear out, or seize from contaminants due to the protective boot tearing open. A worn joint is prone to breakage, or other hazards. If your vehicle needs a new front axle shaft, install a quality TRQ axle that is engineered to your vehicle’s specifications. This video shows you how to install a front axle shaft in your 1998-2011 Ford Ranger.
• Check here for more videos on the 1998-2011 Ford Ranger: • Ford Ranger 1998-2011 ...
This process should be similar on the following vehicles:
1998 Ford Ranger
1999 Ford Ranger
2000 Ford Ranger
2001 Ford Ranger
2002 Ford Ranger
2003 Ford Ranger
2004 Ford Ranger
2005 Ford Ranger
2006 Ford Ranger
2007 Ford Ranger
2008 Ford Ranger
2009 Ford Ranger
2010 Ford Ranger
2011 Ford Ranger
Tools you will need:
• Pry Bar 1aau.to/oa/1AXA...
• Brake Caliper Hanger 1aau.to/oa/1AXA...
• Straight Cutters
• 3/8 Inch Air Impact Gun
• 3/8 Inch Drive Ratchet 1aau.to/oa/1AXA...
• Ratchet 1aau.to/oa/1AXA...
• Socket Driver
• Torque Wrench 1aau.to/oa/1AXA...
• Bungee Cord
• Paper Towels 1aau.to/oa/1AXS...
• Rust Penetrant
• Center Punch 1aau.to/oa/1AXA...
• Floor Jack 1aau.to/oa/1AXA...
• Hammer 1aau.to/oa/1AXA...
• Jack Stands 1aau.to/oa/1AXA...
• Wheel Chocks
Subscribe: / @trq
Check out our playlist:
Ford Ranger 1998-2011 3rd Generation: • Ford Ranger 1998-2011 ...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts
√ *Do it Yourself*
√ *Save Money*
Great work. Magical at the end I noticed you did your shocks, rotor and brake caliper housing replaced! All at once . Night five
+Deon 0026 Thanks for watching our video! 1aau.to/m/Shop-TRQ
This was the cleanest and direct video for this procedure I have seen and included all toque specs
My 2 cents : don’t undo the lower shock bolts unless absolutely necessary. I was able to snake my axle out while leaving the shock bolts in. My shock bolts look absolutely dreadful; I anticipate them breaking upon removal , but that’s a job for another day.
Why are you not mentioning bolt sizes. Feels like a rushed instructional
Well done. I love that this video has torque specs. That's not common enough for repair videos. Thanks for the help!
Great video, your talk as you walk through the process was, well I'd have to say the best I've heard out if everyone of the videos I've watched on here great tutorial. Thanks for your help
I have a 99 Ford ranger in it only has a plastic snap ring that holds the axle into the hub
do you have any videos on removing the front diff cover thanks.
How come nobody ever mentions the bearing inside the differential that the axel will sit in? Is this something that just doesn't usually go bad or would it be a huge pain in the a to replace?
When I trun sharp right while 4x4 on, I heard strange cranky sound from right front wheel looks like sleeping from Axel gear. Can you suggest me what it is please. Hope fully it going to help me alot with my 2012 FORD RANGER front axle shaft replacement if my guess is correct.
Is it possible to leave the axle in the hub assembly when lowering that steering knuckle off the ball joint shaft? I was wanting to pop the axle out of the differential and remove it while still attached to the knuckle and hub.
good video and instruction but could you have found a more rusted truck!!
Thanks for sharing. Good job.
Boa tarde tenho uma ranger ano 2000 distema roda livre gostatia de saber se há pocibilidade de ser subistituido por homoconetica fixa
best damn video I have seen on u-tube
Boskuu saya mau nanya saya punya renjer tahun 2010 tiap saya masukin 4x4 jalan nanya dikit aja punyi ctek""" tapi kalau jalan lurus gak punyi gituu apanya kira"" bosku ???
Can you do this without removing the outer tie rod from the steering knuckle? if not, would you have to get an alignment after this procedure? thank you.
Dont need an alignment as the tie rod is going back in the same spot on the knuckle
I managed to get my bad one out but had to turn the wheels and try from different angles. The new one went in really easy however.
when I do this, I put an alignment mark on the parts to put them back in position
Thanks
What is the nut size for the CV joint?
Hey, just done this and my abs light is now illuminated, took it for a drive to see if it would clear but it hasn't.
Typical, when I removed the sensor, it was plastered in rust. Now it's clean, it's refusing to work 😂
Gracias muchas Gracias
hi i bought this exact part for my truck but it doesnt come with the spiral locking clip which holds the cv shaft in place and stabilizes the 4 wheel hub,where can i get the spiral locking clip to buy?
We're you ever able to get your CV tight and not clicking? I have the same 4x4 vacuum hub and could never get the new cv axle tight. You can get a new spiral clip on amazon
Replace that lower control arm while you're at it
Thanks for the video.
I’m doing the passenger side (uk) and cannot get the axle out from the transfer case.
It’s even more difficult to get to it - does it simply knock out with the pry bar like the video
Has anyone done this on the other side?
I cannot find a video anywhere!
Dude I need the passenger side 😭
Currently doing the passenger side - I’ll update you when I get it out! 😉
Give it a couple loving bonks
Does not just tap in like that with a rubber mallet! Some BS!!!
what kind of Ford Ranger is that because I have a Ford Ranger and it doesn't have those parts, I BELIEVE you got confused in the title of your video.🤔🤔🤔🤔🤔
If your Ranger isn’t 4x4 it wouldn’t have CV axles as you don’t need to power the front wheels.
99 ford ranger 4x4 do not have a outer nut !!!!
Sell it and buy a real truck