I would check drum brakes, front brakes, coolant, bleed brakes, if clutch seems to slip relplace that too, spark plugs. Basic maintenance. Owner manual can be found on website.
Great video ! How long it took you the whole thing ? I see you take off your pullover while putting back the shaft in the yoke (that drop down a bit) and the video is cut. How did you do it ? Thank you
Question, how did you get the female coupling holder nut off? I'm talking about the one with the folded lip you need to pry open, but you need to hold the assembly in place to take the 22mm nut off, how did you manage? Vice?
Where did you find the whole final drive assembly like that? I am having the same issue and I'd like to replace every like you did, but the only whole assemblies I've found have the same issue...
I have exactly same problem , when you received the new drive shaft assembly was the shaft firm and not loose and wobbly like what you showed on this video?
Hi there 👋. I start reassembling all of this final gear unit yesterday and had a question. Maybe you know how that bond 1207B should be applied? There are 2 holes for breather on final gear case. Thank you.
It looked to me like there were five bolts to remove that frame + the one bolt with the hex head, do those six bolts have a torque spec or do they just going tight with blue thread lock... Same question for the three acorn bolts.
You won’t. It’s just a chance you have to take. Ask the seller how many miles is on the bike when the shaft came off. The less miles the better. When you get the used shaft inspect and put grease on the splines before install it. Good luck
Nice video clearly briefed fr replacing final drive shaft. Where is the EBay need full address & contact # for my future requirement if any. I own c 90, boulevard is good bike from Suzuki.
Thankbyou for this! You have a great spirit to do this to show us how to keep these bikes on the road.
Thank you! Great video. I have a 2014 C50 BOSS. I love this bike. Your video I will save if and when I need to take on this job
Wonderful, thanks for the video. I love Japanese motorcycle.
I love that you have tubeless wheels
Great attitude! I have a 91 VX800 60K k and hoping they greased spline properly. Thanks for the tips.
Thank you brother !! Putting mine back together today
Most excellent video. Other than the final drive what else has typically needed replacement by 30k miles?
I would check drum brakes, front brakes, coolant, bleed brakes, if clutch seems to slip relplace that too, spark plugs. Basic maintenance. Owner manual can be found on website.
SO GREAT THANK YOU MUCH .
Cuanto aceite lleva y de que tipo? Saludos....
Thx for the nice vídeo!
Great video! Thank you
Excellent video. Where did you get the whole final drive assembly and how much if you don't mind me asking?
eBay. I think it’s $100
Great video ! How long it took you the whole thing ? I see you take off your pullover while putting back the shaft in the yoke (that drop down a bit) and the video is cut. How did you do it ? Thank you
Took me little over 5 minutes get the shaft in.Just have to rotate the shaft and angle down. It will go in eventually
@@Yololife813 Thank you !
@@Yololife813 And what about the whole thing ? How long it took you more o less ?
@@alexandremiro probably little more than 2.5 hrs. If I did have to do the video, probably 1.5 hr
@@Yololife813 Thank you !
Question, how did you get the female coupling holder nut off? I'm talking about the one with the folded lip you need to pry open, but you need to hold the assembly in place to take the 22mm nut off, how did you manage? Vice?
I used my impact wrench
Where did you find the whole final drive assembly like that? I am having the same issue and I'd like to replace every like you did, but the only whole assemblies I've found have the same issue...
eBay
I have exactly same problem , when you received the new drive shaft assembly was the shaft firm and not loose and wobbly like what you showed on this video?
It was loose but not much like the one on the vid
@@Yololife813 thank you
Good video. How many miles do you have on it?
30000miles
Hi there 👋. I start reassembling all of this final gear unit yesterday and had a question. Maybe you know how that bond 1207B should be applied? There are 2 holes for breather on final gear case. Thank you.
Sorry I don’t know how’s that bond or how to apply it. I just replaced the entire shaft drive.
It looked to me like there were five bolts to remove that frame + the one bolt with the hex head, do those six bolts have a torque spec or do they just going tight with blue thread lock...
Same question for the three acorn bolts.
I believe They all have torque specs. You can Google it
I just hand tight them.
@@Yololife813 I'll double-check my service manual, Haynes manuals are not all that well written.
Just today, it happened to my wife's 2009 m50. Question. If you buy a used one from eBay, how would you know that it won't happen a year later again?
You won’t. It’s just a chance you have to take. Ask the seller how many miles is on the bike when the shaft came off. The less miles the better.
When you get the used shaft inspect and put grease on the splines before install it. Good luck
Great job. May I know the part number that is not working?
I ordered on eBay the whole used shaft. There was no part number. If you need part #go on partzilla.com and look up part number on their site.
@@Yololife813 thank you so much
Does anyone know where I can buy a replacement driveshaft for my 2009 c50????????
@@gunr2012 eBay
That’s where I got my
Here you can explain how to open and change the clutch valves of a Susuki Boulevard C50 2007 bike.
Nice video clearly briefed fr replacing final drive shaft. Where is the EBay need full address & contact # for my future requirement if any. I own c 90, boulevard is good bike from Suzuki.
eBay app you can order anything on there. Just do a search
I need to find tubeless wheels for my boulevard 08
Try eBay?
Where is the predecessor of the engine operating, Susuke Boulevard, opening and installation diagram
What year is bike? An are those factory rims?
2009 factory rims
It's a C50C
This manufacturer flaw I doubt is accidental, it’s intentional because it’s happened to too many.
Just swapped mine out.. now my rear tires locked up😅😫
At least now I have your video for two!
Did you figure out why it lock up?
You overdone it. It’s almost always the splines on the shaft drive itself