The problem with relative dry cement method is that you get voids from air bubbles in the mix and if you try to counteract this you get a pancake effect where there is insufficient moisture between each compressed layer and when partially dried the pancake can literally fall apart. Unless you have a 10 to 20 ton press to deliver 2000 lb per square inch pressure to get rid of the voids in a single compression stroke then slop moulding is the only method for DIYers that more easily removes voids so long as you have an vibration machine designed for that purpose.and molds that can be fixed to the table and are capable of withstanding the forces involved. The big picture is not only how many bricks one can make per day by the demonstrated method but the suitability of the bricks made for the purpose intended.
@@jimihindrix7977 I have not consider a video yet because I've jumped in the deep end by copying a simplistic but inadequate vibration table design that everybody seems to promote using a v-belt drive with a rocker spring isolated table top. This can of worms that I still struggling to cope with manifests itself when one goes from a 5 brick batch to a 20 or 30 brick batch. The table top drops and the vbelt looses friction or comes off altogether without idler pulleys with springs and or a motor height adjustment system. But what I have come up with ( worth mentioning in dispatches ) is a pretty useful slop molding system that couple two completely opposite ideas in a single fix. Taking a rigid soap mold concept aimed at dimensional stability from a youtube video, exact length and width or exact length and depth could be achieved by |_______| wooden rigid form cut and screwed to exact dimensions. The trick is make this section movable using SS piano hinges attached to the long side and a suitably sized base and to close the other side with a section that overlaps the ends that is also attached to the base with SS piano hinges and clamped to the sides using toggle clamps. Cutting a suitable size tile for the base enables a wet brick after about 1 hour to be removed from the mold after the initial set since both sides are lifted out of the way for it to slide out undamaged and the mold cleaned in situ for reuse. A slop mold system for bricks might be defined as a system of vibration molding that achieve a glass like surface on the bottom of the brick that is free of air bubbles using minimal water. I'll try and email you some pics.
I do not agree, If high-quality materials, then everything will be OK!I have a couple of such ready-made bricks, and in order to break them, you need to make a lot of effort, not with your hands, but with a sledgehammer!!!)))
до конца года достроим чулан )))По себе стоимости мерседеса .Надо было хотя бы посередине сделать отверстия ,чтоб меньше раствора использовать ,и кирпич будет легче и экономия цемента . Да и кладка чем легче ,тем меньше нагрузки на нижний ряд кирпичей,да и какая никакая термоизоляция .А вообще если уж делать такие "кирпичи" ,легче сразу опалубку поставить на всю стену и залить бетоном . Да технология этих форм смахивает на каменный век , Разбирай,собирай,вставляй-конструктор лего )))
I like everything about this "IDEA" however, there's 2 things wrong here..... the bottom is open therefore you're compacting the cement to whatever is underneath when you do it so its very possible you can have issues with your bricks later from that. You need to have something underneath. The second thing wrong with this is that there's just not enough water, doing it this way with little moisture will cause it to be brittle and have possible air pockets because you do not have enough pressure during compaction and the integrity of your bricks could very easily fail. It is a great idea but there needs to be a few modifications is all 👍 👌 👍
Покрасить дерево обязательно. Да и без вибростола это фигня полная с таким сухим раствором. Замешать с теми же пропорциями, добавлением пластификатора и по весам, то будет нормально.
Не хватает отверстия в центре кирпича, чтобы можно было формировать кладочные ряды с арматурным укреплением
Я думаю это для дорожки.
Parabéns vc e um gênio 👏🏽👏🏽👏🏽 Deus abençoe vc sempre 🙏🏽
Ada ngak dijual cetakanya
😮encore merci❤
عليك وضع قطعة من النايلون تحت القالب حتى ﻻتلسق في ارضوفك اسرع وانظف .
اتشكر جهودك ﻻنهافكرةممتارة للفقير ويعرف النسب للقصوة المطلوبة
Parabéns felicidade ficou perfeito
Very creative sir. Wonderful.
Не хрупкие такие кирпичи получились? Может песок со щебнем добавить для прочности?
Terima kasih motivasi dan inspirasi saya sudah SUBSCRIBE salam kenal dari saya Nasipan Podomoro kotamobagu Sulawesi Utara. Kreatif dan inovatif
excelente parabens mestre
The problem with relative dry cement method is that you get voids from air bubbles in the mix and if you try to counteract this you get a pancake effect where there is insufficient moisture between each compressed layer and when partially dried the pancake can literally fall apart. Unless you have a 10 to 20 ton press to deliver 2000 lb per square inch pressure to get rid of the voids in a single compression stroke then slop moulding is the only method for DIYers that more easily removes voids so long as you have an vibration machine designed for that purpose.and molds that can be fixed to the table and are capable of withstanding the forces involved. The big picture is not only how many bricks one can make per day by the demonstrated method but the suitability of the bricks made for the purpose intended.
Bom
What do you mean by: slop moulding? Can you share a video that shows this method? Thanks
@@jimihindrix7977 I have not consider a video yet because I've jumped in the deep end by copying a simplistic but inadequate vibration table design that everybody seems to promote using a v-belt drive with a rocker spring isolated table top. This can of worms that I still struggling to cope with manifests itself when one goes from a 5 brick batch to a 20 or 30 brick batch. The table top drops and the vbelt looses friction or comes off altogether without idler pulleys with springs and or a motor height adjustment system. But what I have come up with ( worth mentioning in dispatches ) is a pretty useful slop molding system that couple two completely opposite ideas in a single fix. Taking a rigid soap mold concept aimed at dimensional stability from a youtube video, exact length and width or exact length and depth could be achieved by |_______| wooden rigid form cut and screwed to exact dimensions. The trick is make this section movable using SS piano hinges attached to the long side and a suitably sized base and to close the other side with a section that overlaps the ends that is also attached to the base with SS piano hinges and clamped to the sides using toggle clamps. Cutting a suitable size tile for the base enables a wet brick after about 1 hour to be removed from the mold after the initial set since both sides are lifted out of the way for it to slide out undamaged and the mold cleaned in situ for reuse. A slop mold system for bricks might be defined as a system of vibration molding that achieve a glass like surface on the bottom of the brick that is free of air bubbles using minimal water. I'll try and email you some pics.
B b kiilantan mood jk huuh
Huuh
I do not agree, If high-quality materials, then everything will be OK!I have a couple of such ready-made bricks, and in order to break them, you need to make a lot of effort, not with your hands, but with a sledgehammer!!!)))
น้องฟุ๊คสุดยอดครับ
Semangat terus mas Indonesia menyimak dan juga di Indonesia juga ada oke trimakasih
Formidable. Merci
Very good!!!
до конца года достроим чулан )))По себе стоимости мерседеса .Надо было хотя бы посередине сделать отверстия ,чтоб меньше раствора использовать ,и кирпич будет легче и экономия цемента . Да и кладка чем легче ,тем меньше нагрузки на нижний ряд кирпичей,да и какая никакая термоизоляция .А вообще если уж делать такие "кирпичи" ,легче сразу опалубку поставить на всю стену и залить бетоном .
Да технология этих форм смахивает на каменный век , Разбирай,собирай,вставляй-конструктор лего )))
thanks bung, jadi nmbh inspirasi ..
Это когда время лишнего вагон ,монолитом быстрее
So nice ,thanks so much .good luck
thank you
Gostei muito obrigado
falta perforacion para los tensores el tensor es anti sismico
I like everything about this "IDEA" however, there's 2 things wrong here..... the bottom is open therefore you're compacting the cement to whatever is underneath when you do it so its very possible you can have issues with your bricks later from that. You need to have something underneath. The second thing wrong with this is that there's just not enough water, doing it this way with little moisture will cause it to be brittle and have possible air pockets because you do not have enough pressure during compaction and the integrity of your bricks could very easily fail. It is a great idea but there needs to be a few modifications is all 👍 👌 👍
Покрасить дерево обязательно. Да и без вибростола это фигня полная с таким сухим раствором. Замешать с теми же пропорциями, добавлением пластификатора и по весам, то будет нормально.
Super idea
thank you
STP traduire en français. C'est formidable. Merci pour la vidéo
Для сарая пойдёт .
Cement.. Or reti masala map kitna rakhana he
Для вьетнамской хибары пойдет...
Thankyou brick idea
Good job sir
Для быстрой работы нужен вибростол
Joss👍
А какой номер наждачного круга ты используешь?
That's great, bro!!!!
nice
cool! but had to mute the audio...
Что крутого , они развалятся под нагрузкой
Como Aser que queden más altos de 20 de largo por 30 y 10 de anchos
Bahan pasir semen. Batako lebih baik dr pd hebel di plester lbh lengket
Nice brother :ye brick frem order me mil jata to mere lete acha tha mil sakta he kya?
Muito bom
Nice
Super
Gracias🎉
Good
thank you
Acredito que só cometeu um erro: ter procurado um lugar mais apropriado ou colocado um plástico em baixo para não manchar o piso!
👍👍👍👌👌👌
सांचा में बनवाना है तो बना दोगे। सर 5 pise cash on dilevery
não está faltando um lado positivo para encaixar?
thank you so much
Cement kost in Nederland meer dan dat ik de stenen koop 🙄
заодно и кафель засрал
Dilengketkan. Sebelah.biar tambah cepat
Eu gostaria de saber onde eles investiram esse dinheiro. Se eles para vão devolver esse dinheiro para os cofres públicos.
♥️♥️♥️👍👍👍
Para que sirven esos bloques
I am very sad. He is spoiling the nice tile floor by applying cement on it!
👏🏻👏🏻👏🏻👏🏻
thank you
42-16 kaise kare house
Elinaldo Barroso STM-PARA
Xting nya yg lama
А какой пропорции раствора
1 цемент 3 песка 1 вода
@@STARiK56 такие пропорции пригодны для конкретной марки цемента. Пропорции составляющих раствора зависят, в первую очередь, от марки цемента.
Ro materiyal
Oke
thank you
Achhu price Tel me
Звук 🤬
احمد مصطفى
M I
Mogu biti i tanji, 10 cm je mnogo
Formidable, Merci
falta perforacion para los tensores el tensor es anti sismico