Hey man, great Video! I'm starting now in the hobby, this past week my Meteor65 pro 2022 ELRS and the Radiomaster Boxer arrived. I spent more them one week trying to Bind it and I couldn't. I updated RX and the Radio to version 3.2.1, 3.2.0, 3.0.1 and 3.0.0. I also updated it with and without passphrase and nothing worked. I also checked if I had match mode enabled, and both were off. I also try to put it in bind mode by turning it on and off 3 times and nothing, it just blinks. I used both: BETAFPV AIO 2400 RX and DIY 2400 RX firmware. I have no idea what I do more! 😢 do you have any idea I can do more to get it working ? Thanks man!
Hello dude I got crazy to bind it with his radio Lite 3 …can you immagine? Finally I wrote to Betafpv several times and that’s was the answer : Based on the video you sent, I found two problems. The configuration information of the aircraft is lost, and the firmware version of the controller is 1.0.1, which is inconsistent with the aircraft. Below is my solution, hope it will help you. 1）Connect the drone and Betaflight, click the CLI tab, then click Load from file, select the CLI dump file linked below, click Open, and then click Execute, the configuration information will return to normal. support.betafpv.com/hc/en-us/article_attachments/15324681477785/BF411_4.3.0_M65_Pro_A_ELRS_V2.0_ELRS2.4g_20230203.txt 2）Press and hold the Setup button of the controller and press the power button at the same time, the blue light is always on, then connect the controller and the BETAFPV configurator, select the firmware version as shown in the screenshot below, then click the connection in the upper right corner, and then click Load Firmware[ in the lower right corner Online], and finally click Flash Firmware.Then disconnect the controller and USB data cable, press the power button once, and the blue light goes out. 3）Then follow the binding steps I provided before. You can follow the solution I provided. 1) Plug and unplug the FC for meteor65 pro three times, the receiver LED flashes twice quickly, and the receiver enters the binding mode. 2）Turn on the LiteRadio3 controller, put the throttle stick to the lowest position, and press the Bind button of the controller. 3) When the green light of meteor65 pro is always on, it proves that the binding is successful. If you can't unlock it by pressing the SA button, you can connect LiteRadio3 and BETAFPV configurator, set the channel mapping sequence as shown in the figure below, remember to click save.
Impressionante
Hey man, great Video!
I'm starting now in the hobby, this past week my Meteor65 pro 2022 ELRS and the Radiomaster Boxer arrived.
I spent more them one week trying to Bind it and I couldn't.
I updated RX and the Radio to version 3.2.1, 3.2.0, 3.0.1 and 3.0.0.
I also updated it with and without passphrase and nothing worked.
I also checked if I had match mode enabled, and both were off.
I also try to put it in bind mode by turning it on and off 3 times and nothing, it just blinks.
I used both: BETAFPV AIO 2400 RX and DIY 2400 RX firmware.
I have no idea what I do more! 😢
do you have any idea I can do more to get it working ?
Thanks man!
Hello dude I got crazy to bind it with his radio Lite 3 …can you immagine? Finally I wrote to Betafpv several times and that’s was the answer : Based on the video you sent, I found two problems. The configuration information of the aircraft is lost, and the firmware version of the controller is 1.0.1, which is inconsistent with the aircraft.
Below is my solution, hope it will help you.
1）Connect the drone and Betaflight, click the CLI tab, then click Load from file, select the CLI dump file linked below, click Open, and then click Execute, the configuration information will return to normal.
support.betafpv.com/hc/en-us/article_attachments/15324681477785/BF411_4.3.0_M65_Pro_A_ELRS_V2.0_ELRS2.4g_20230203.txt
2）Press and hold the Setup button of the controller and press the power button at the same time, the blue light is always on, then connect the controller and the BETAFPV configurator, select the firmware version as shown in the screenshot below, then click the connection in the upper right corner, and then click Load Firmware[ in the lower right corner Online], and finally click Flash Firmware.Then disconnect the controller and USB data cable, press the power button once, and the blue light goes out.
3）Then follow the binding steps I provided before.
You can follow the solution I provided.
1) Plug and unplug the FC for meteor65 pro three times, the receiver LED flashes twice quickly, and the receiver enters the binding mode.
2）Turn on the LiteRadio3 controller, put the throttle stick to the lowest position, and press the Bind button of the controller.
3) When the green light of meteor65 pro is always on, it proves that the binding is successful.
If you can't unlock it by pressing the SA button, you can connect LiteRadio3 and BETAFPV configurator, set the channel mapping sequence as shown in the figure below, remember to click save.
Hi I am planning to order one. Does it bind to the Radiomaster Boxeer ELRS?
Hello I don’t know but if you order the one with ELRS most probably you can
It does, you will likely need to update the reciever to ELRS 3 but it's serial so can be done without upsetting Betaflight.
Ciao, con che telecomando l’hai usato ?
Lite radio 3 BetaFPV
Video seppere