HIPA Generator Dual fuel carburetor LPG CNG conversion

Pete is going to show how to install A HIPA Generator Dual fuel carburetor LPG CNG conversion kit. Here on the homestead, we’re working on our emergency Preparedness. Part of that is getting your generator’s ready to run on different kinds of fuels. So you’re not limited to one type of fuel in case of emergency. He wanted to show how to get his gas generator to run on propane.
www.hipastore.com
HIPA Generator Dual fuel carburetor LPG CNG conversion kit 4.5-5.5KW GX390 188F manual choke a.co/d/i2VXqF6

[@TheMaclays]

Great job Pete. Always pays to be prepared. Take Care.

[@cheaphomesteading]

Thank you man It definitely is especially after the big windstorm we had this summer. Thanks for watching man

[@gmsgabaradama2009]

You were supposed to set it by Hertz with a non-inverter generator. You should set that to 61.5 Hz

[@rengel7]

James Condon would be furious.
Not one time in this video did I see a torque wrench. 😮

[@gmsgabaradama2009]

@@rengel7 you already know lmao

[@HipaParts]

Thanks, Pete. Very detailed and helpful video.

[@cheaphomesteading]

Thank you for sending the carburetor. It worked flawlessly. Have a great day

[@philliphall5198]

Hipi make the best kit and carb are for sure the best

[@cheaphomesteading]

I’ve always been happy with there stuff

[@fourbyfour4]

Why set it for 110v instead of 120v. Thanks for the video.

[@marksparkplug7758]

Thanks Pete.

[@cheaphomesteading]

Thanks man

[@saywhat..]

Great info thanks

[@cheaphomesteading]

Thanks man

[@ogheneroamos5535]

Please what is the disvantage of the carburator usage of the dual popose fuel/gas slida?

[@rickmcdonald4552]

Have you had any problems with motor by switching to manual choke. I notice you did not plug up vacuum line from choke. Another video I saw he had to plug hose or it would not run correctly.

[@philliphall5198]

Looks just like your

[@philliphall5198]

Merry Christmas and Thank You
Please let me know how it ran out ok
Fixing to put starter kit on it and this would be helpful for my Girl

[@cheaphomesteading]

Sorry it took so long. It’s still running great.

[@philliphall5198]

Are you still happy with it ??
Had any trouble ??
Was it easy to install on generator??

[@cheaphomesteading]

It was easy to install, and I haven’t had any trouble with it. It actually starts a little easier than on gas. Thanks for watching.

[@andyblanchard6231]

Hey Pete I know it’s been some time . I’m rebuilding a perkins d3.152 and I was watching your video on the timing cover when you torqued it to 28 was that footpounds or nm ? Thanks

[@cheaphomesteading]

Sorry man I can’t remember. I borrowed the manual when I rebuilt the motor so can’t even look now. You can look up a universal torque spec for the size of bolt and thread. it will give you a rough idea. I wouldn’t do that for internal bolts. But for the valve cover it should be good. Thanks for watching and hope you get it fixed

[@andyblanchard6231]

Thanks I went 28 ft pounds for a 5/16 24 bolt. it should be around 21 went 7 pounds over do you think it would be ok to leave? It’s the inside timing cover

[@cheaphomesteading]

Its good if the bolts tightened up. I would leave them. It’s not that much over. I’m glad you are getting it together. Have a great night

[@andyblanchard6231]

Thank you 👍

[@philliphall5198]

Ft/lbs

[@philliphall5198]

I have a 55 Genrex and someone cut wire off low oil sensor and kill switch wires Try to find how to rewire it with new low switch

[@philliphall5198]

Yellow wire goes to sensor coming out of block

[@philliphall5198]

Also if it won’t start then unplug blk wire coming out of little silver box with yellow wire

[@philliphall5198]

I’m propane certified and 72
I know about repairs but is kit good ???

[@cheaphomesteading]

I’m very happy with it. It works great. Thanks for watching.

[@philliphall5198]

I just put 3 kits on for customers and they are great 👍