@@hastingsangler the main shift is 10 mm would make the washers solid then make the hole after they have cured what price dave do you sell 28mm pumps dave s/steel asking for a freind
@@DaveMielczarek hi sorry i only make 22mm pumps that way its easier to buy and make the seals only 1 size as for your seals if you plan to puch through the solid 1s i would make your seal 24mm they will expand once the rod is pushed through and give you room to adjust the pump for pressure good luck
I have been watching all your videos on the copper bait pumps 22mm so im going to try and build one. Ive an 8mm stainless rod for the inside and you mentioned you welded on a 6mm bolt. I was goin to jus thread the bar and use 8mm nuts and stuff jus wondering would it still work the same and also on your silicon washers what size hole is the mould is actually 22 mm or 20mm im assuming you leave a small bit as when pushed through the bolt it will naturally expand with the pressure? As for all 8mm sized the washer hole would be 8mm then? Thanks
Hi Darren yes you could just 8mm thread the rod if you have the tools but i think you cant beat the 6mm thread everything is easier with the smaller thread and the seal will be less hassel you can make 19mm holes and make solid seal then just push through the seal and yes they will expand to a perfect fit i done them that way for years for my self good luck i have a video coming out with how i make my new pumps and how my seals have got better
@@hastingsangler brilliant dave thanks a mill for your reply i might just hold off on building it to see your new spin on things thanks a mill once again.
Hi dave what is the lenth of your pump from the end of the tube to the top of the handle mine seems a bit to long making it harder to pull up the handle is it possible to cut 10inches off the tube then shorten the shaft by 10inches it would make it a bit easier for me
Jezz Dave that must be a bloody long pump if you want to cut 10" off all depends how tall you are im 5ft 11" and my pumps are 1mtrs long from end to end if they are 6ft plus i make them 1.1mtrs long if you make the pump too short you wont get the suction you need hope this help Dave
@@hastingsangler morning dave just measured my pump it's 43 inches from end to end iam 5foot 10 inches when pulling the handle its a job pulling it to far especially with me having a bad shoulder I tried my freinds pump which is 850mm and that seems a lot better so it looks like I'll have to sell mine and buy the shorter on there is a company in ramsgate that does them the pump you use is shorter and looks a lot easier to use thanks dave
@DaveMielczarek hi Dave why not just cut the shaft and rethread it would be cheaper and easy to do what is the name of the pump you are thinking of getting
Brilliant found it.. People are slowly finding out just how good these are.. Makes the pump action super smooth great seal n no lube other than sea water required.. Nice 1.. I'm gonna have a little go at making some.. When fitting in pump, do you use just metal washers or is there some thing else between the silicone and the metal washers. What size washer 8mm ? Cheers glad to have found your vid again..
@@hastingsangler Its missing all the washers and nut off the end. Also the thread on the rod that they go on is flat on one side! It's a 28mm pump. I was given it and I would like to get it up and running. Any help would be appreciated.
@@neilblackford9670 Hi are you local to hastings the washers and nut are not a problem but my friend from kdr bait pumps has 28mm seals made up ready infact i think you can but the whole lot he is on facebook kdr pumps and parts hope this helps
............Great video, really explained well. Now just need to know how to get those Lugworms, tricky little things.
Hi im glad you liked it at the moment the worms are hard to get but keep trying 👍👍👍
Great video simple guide to making washers keep em coming
Thanks, will do!
Excellent idea mate,I will definitely give that a try 👍
Hi thank for watching and post i can say they work a treat just got back from a good session on the worms tight lines👍
Hope to see you Sunday...Brian
I hope so too!👍👍👍
Vaseline the walls of the mould too?
hi richard i do mate the seals work great😀😀
Hi dave what size holes would I need to drill to make silicone washers for a 28 mm pump
@@DaveMielczarek hi what size shaft are you going to use M8 I would say are you going to make them solid or with a hole in
@@hastingsangler the main shift is 10 mm would make the washers solid then make the hole after they have cured what price dave do you sell 28mm pumps dave s/steel asking for a freind
@@DaveMielczarek hi sorry i only make 22mm pumps that way its easier to buy and make the seals only 1 size as for your seals if you plan to puch through the solid 1s i would make your seal 24mm they will expand once the rod is pushed through and give you room to adjust the pump for pressure good luck
@@hastingsangler thanks for your help dave keep up with the videos
I have been watching all your videos on the copper bait pumps 22mm so im going to try and build one. Ive an 8mm stainless rod for the inside and you mentioned you welded on a 6mm bolt. I was goin to jus thread the bar and use 8mm nuts and stuff jus wondering would it still work the same and also on your silicon washers what size hole is the mould is actually 22 mm or 20mm im assuming you leave a small bit as when pushed through the bolt it will naturally expand with the pressure? As for all 8mm sized the washer hole would be 8mm then? Thanks
Hi Darren yes you could just 8mm thread the rod if you have the tools but i think you cant beat the 6mm thread everything is easier with the smaller thread and the seal will be less hassel you can make 19mm holes and make solid seal then just push through the seal and yes they will expand to a perfect fit i done them that way for years for my self good luck i have a video coming out with how i make my new pumps and how my seals have got better
@@hastingsangler brilliant dave thanks a mill for your reply i might just hold off on building it to see your new spin on things thanks a mill once again.
Hi dave what is the lenth of your pump from the end of the tube to the top of the handle mine seems a bit to long making it harder to pull up the handle is it possible to cut 10inches off the tube then shorten the shaft by 10inches it would make it a bit easier for me
Jezz Dave that must be a bloody long pump if you want to cut 10" off all depends how tall you are im 5ft 11" and my pumps are 1mtrs long from end to end if they are 6ft plus i make them 1.1mtrs long if you make the pump too short you wont get the suction you need hope this help Dave
@@hastingsangler will measure my pump in morning dave and send you the measurements from end of tube to top of handle
@@DaveMielczarek ok dave no problem how tall are you
@@hastingsangler morning dave just measured my pump it's 43 inches from end to end iam 5foot 10 inches when pulling the handle its a job pulling it to far especially with me having a bad shoulder I tried my freinds pump which is 850mm and that seems a lot better so it looks like I'll have to sell mine and buy the shorter on there is a company in ramsgate that does them the pump you use is shorter and looks a lot easier to use thanks dave
@DaveMielczarek hi Dave why not just cut the shaft and rethread it would be cheaper and easy to do what is the name of the pump you are thinking of getting
Brilliant found it.. People are slowly finding out just how good these are.. Makes the pump action super smooth great seal n no lube other than sea water required.. Nice 1.. I'm gonna have a little go at making some.. When fitting in pump, do you use just metal washers or is there some thing else between the silicone and the metal washers. What size washer 8mm ? Cheers glad to have found your vid again..
Hi I use 18mm washer for the seals
great vid
Hi Les Hope your well mate been tinkering while weathers been bad
Hi new subscriber to your channel and really enjoying it!! Just wondering if you fix bait pumps??
Hi what seems to be the problem with the pump and what diameter is it
@@hastingsangler Its missing all the washers and nut off the end. Also the thread on the rod that they go on is flat on one side! It's a 28mm pump. I was given it and I would like to get it up and running. Any help would be appreciated.
@@neilblackford9670 Hi are you local to hastings the washers and nut are not a problem but my friend from kdr bait pumps has 28mm seals made up ready infact i think you can but the whole lot he is on facebook kdr pumps and parts hope this helps
Hi do you sell these and what do they cost
How many do you need
Nice vid mate
Hi Thank you for watching and taking the time to post cheers👍👍