That is good i am using the sensors with ESPHOME and they work quite good. Will be good to get read of my hub for one of this to not ue multiple devices.
I purchased a couple of these but had to put ESPHome on them (no power monitoring). I'm definitely going to reflash them with Tasmota now! Thanks Travis. Great video as always.
@16:50 you mention getting unit connected to mains... (I'm assuming you forgot to mention never connect to mains while the TX/RX pins are connected to laptop, aka first disconnect those)
Very nice video, but I don't have many products and would like to use just Tasmota with a local MQTT Raspberry Pi and no HA but can't find any videos because it is all HA and would love to see some videos without HA
The Bluetooth deal opens up some options big time. Glad to see pads broken out, no glue, no esp32 efuses burnt. Like they meant for this community to buy it. Someone gets the "more sales" theory at iTead.
Good guide, thanks . I'd like to try using it to control electric shutter motor. Do you know of a guide for doing something like that with sonoff dual and tasmota ?
Hi, How can I set the switchmode according to the original software? Specifically "Working mode, switch, External Trigger mode, for Channel 1, Following mode"
i would assume this is a wifi version, is there any point of flashing these devices with tamsota if they were zigbee, since you can use ha and z2mqtt? one more question how this device will work in case of a complete network failure, like shelly even if your wifi is down when you flip the switch the light will turn on , and how reliable are they ? I'm about to install a bunch of them and confused between shelly and sonoff
You don't flash things that are zigbee usually, there are sometimes OTA updates for them but they are local by nature. Really kind of a toss up between the two, Shelly does have the pin headers usually for open source firmware
Got mine flashed using your instructions and template. But for some reason all the power stats for both channels stay at 0. I've got 700W IR Panel connected to channel 1. No hardware switches connected.
Hello, I am French (translation by google), I wanted to know if it is possible to have: energy today, energy yesterday and energy total for each relay (separately). thank you
Does Sonoff Dual R3 have an alternative Tx & Rx connection? I have 1 unit with no pads on the plate so I cant use it with Tasmota. Any advice would help
The video was actually on a basic that I was doing but fully adaptable to the dual R2. Before I was doing the video thing I did an R2 with a ton of buttons and even used one of the LED traces as an input. ruclips.net/video/WsatPkC2Hf0/видео.html
As you can see I made a little modification to it. That black shiny grain top just wasn't going to work well with a camera pointed at. Inadvertently came to the conclusion I'll never have a smooth work bench/desk again. There's no going back.
@@digiblurDIY i want to use R3 to open/close a window shutter, so there's a way with TASMOTA to configure it as a motor device? i want that Home Assistant will recognize it like a motor..
Hello, i watch and enjoy your channel. First comment :). I followed this instruction and have 3x Sonoff Dual R3 running at my house and a number of other sonoff devices running tasmota. I found only recently the Sonoff Dual R3 has become very laggy, (All other sonoff devices are going well). I have tried factory resetting, updating to the latest firmware, downgrading to an older firmware but nothing seems to fix it. The symptoms are when a light switch is turned on, 3-5 seconds later the light turns on, Very unresponsive webpage. (Not responding after a few refresh then it might come back). If you have any tips of suggestion it would be much appreciated, It almost feels like the hardware is damaged somehow? thanks Grayson
@@digiblurDIY just an update. I managed to solve this. I ended up replacing to a new Sonoff dual R3 to no success, i then realized the problem must of been somewhere else, Then i looked into my network, Turned out to be only a problem when on that wifi VLAN. So internal network issue, Not tasmota, Thanks
Ahhh...yeah if you block stuff like DNS, NTP, etc they get laggy trying to connect to the time server and/or DNS. Point them to a local service and they will be happy.
Hi, I followed the tutorial and managed to make it work without the power monitoring. I used the Tasmota Template in the description. I have the same rev board as you do. Any idea ?
You do need to make sure you flash the latest development version to get the power monitoring like I stated. This bin link works, I just updated mine to it a bit ago. ota.tasmota.com/tasmota32/tasmota32-bluetooth.bin
si i just found out, that i have revision v2.0 where should be used this template: {"NAME":"Sonoff Dual R3 v2","GPIO":[32,0,0,0,0,0,0,0,0,576,225,0,0,0,0,0,0,0,0,0,0,3200,8128,224,0,0,0,0,160,161,0,0,0,0,0,0],"FLAG":0,"BASE":1}
@digiblurDIY did the ble sensors appear in tasmota integration in Home assistant ? To me the only way was to put so19 1 and then they appear in mqtt integration.
@@digiblurDIY ok, but i saw in your previous vídeo (live) that it appears in the integration with an nodemcu esp32 ( or not 🤔). Maybe was other version....
Table top cost a little less than $30 and is intended exactly for this. It was a black kind of faux grain wood, super shiny. Horrible for video cameras with the massive glare. I tried a couple mats but they have glares as well and found these boards and modified my table, I fell in love with the look as well but then one big surprise hit me by accident. I'll never use a smooth work bench/table area again. It's amazing to use for projects and things just grip, don't slide or roll off. Don't worry, I bought extra boards too for replacement needs since they were so cheap at the hardware store.
@@digiblurDIY I understand it was bought for the purpose and as an extra bonus it looks good in the video. But it's still too beautiful for me to work on.
It's no longer 1985 McFly. UL isn't what it used to be and even insurance companies can care less about it. Almost as bad as some of these FCC certs you see on products.
Very informative and helpful… no wasted time and thorough detailed information… needed this video today! Thank you and keep up the great content
Great video! Been looking forward to seeing the Dual R3 in action :)
I ripped the pads off. Ended up scraping off the traces and micro soldering with a microscope. Ended up getting it done but it was stressful.
Ouch. Luckily those other pads are still there.
That is good i am using the sensors with ESPHOME and they work quite good. Will be good to get read of my hub for one of this to not ue multiple devices.
I purchased a couple of these but had to put ESPHome on them (no power monitoring). I'm definitely going to reflash them with Tasmota now! Thanks Travis. Great video as always.
Thanks! I bet they'll get ESPHome support pretty soon going for that chip. Choices are good.
Travis, Great video! The Sonoff Dual R3 looks like a pretty cool device. Interesting to start to see the migration from ESP8266 to ESP32.
Great Video as always! yesterday I was looking for a similar type but with dual Dimmers.
Where is my outtro, Travis? This is not fair!
Slick desk though ;-)
Spoiled yall! I have to dig through more random stuff but I do have some new stuff I am grabbing this weekend with safety harnesses involved 😎
@16:50 you mention getting unit connected to mains... (I'm assuming you forgot to mention never connect to mains while the TX/RX pins are connected to laptop, aka first disconnect those)
Very nice video, but I don't have many products and would like to use just Tasmota with a local MQTT Raspberry Pi and no HA but can't find any videos because it is all HA and would love to see some videos without HA
I would use Tasmota as it has MQTT which is usable by many platforms
Thanks man, great content always.
Glad you enjoyed it
Great video as always! Now I need a couple of these. Ugh. Lol!
The Bluetooth deal opens up some options big time. Glad to see pads broken out, no glue, no esp32 efuses burnt. Like they meant for this community to buy it. Someone gets the "more sales" theory at iTead.
neat, thanks Travis!
Any time!
Awesome tutorial. Thanks T. This with the Lutron toogle switch to momentary hack from your old tutorial...and we got multi press on both switches
Indeed! Or some dimmer control hold buttons.
@@digiblurDIY "dimmer control hold buttons" What are those ? did you cover them in another vid or live session ?
@@digiblurDIY is there switch with 1 position to connect it so I dont get my regurar switch mixed positions
Think I did a while back with a guy doing a rocker and the new switch modes.
Yes. Momentary buttons work for this.
Thanks for you
How to integrate in home assistant
Use the Tasmota HA integration
Can you control a ceiling fan and a light switch with this? 2 different switches same electrical box
Yes. That's the design. Two switch inputs and two relay outputs
can i use this product to operate my ceiling fan....like on off operation??
Yes.
Would be nice if they could individually monitor each of the AC outputs power usage instead of the total consumption
I think now it does? or if not you can go ESPHome to keep those totals on the device.
looking good
Good guide, thanks .
I'd like to try using it to control electric shutter motor.
Do you know of a guide for doing something like that with sonoff dual and tasmota ?
No shutters here so I haven't looked for one.
tasmota.github.io/docs/Blinds-and-Shutters/
@@digiblurDIY
Thanks, i have seen it. I hoped there was a nice video guide 🙂
I am sure there is one somewhere around. I just never looked or paid any attention since I didn't have those.
Hi, How can I set the switchmode according to the original software? Specifically "Working mode, switch, External Trigger mode, for Channel 1, Following mode"
Switchmode1 1 would put it in follow mode. tasmota.github.io/docs/Buttons-and-Switches/#switchmode
What is the device with the 110 in and the White/Green/Black connectors with the flip down?
16:58 talks about it
i would assume this is a wifi version, is there any point of flashing these devices with tamsota if they were zigbee, since you can use ha and z2mqtt? one more question how this device will work in case of a complete network failure, like shelly even if your wifi is down when you flip the switch the light will turn on , and how reliable are they ? I'm about to install a bunch of them and confused between shelly and sonoff
You don't flash things that are zigbee usually, there are sometimes OTA updates for them but they are local by nature.
Really kind of a toss up between the two, Shelly does have the pin headers usually for open source firmware
Nice video, would it be possible to create a rule that creates a XOR state for 1 one output with 2 switches?
I could see doing a decouple setoption and/or rule to get it done.
Got mine flashed using your instructions and template. But for some reason all the power stats for both channels stay at 0. I've got 700W IR Panel connected to channel 1. No hardware switches connected.
Do you have the new version? github.com/arendst/Tasmota/discussions/10793#discussioncomment-1335467
Bracket looks like it would mount on DIN rail. Not common in U.S. residential applications.
Yeah. That was my only thought as I wouldn't mount it on the wall here. Only DIN rail stuff I did was custom telemetry stuff offshore.
Is there any low voltage pins on this device that can be used for i2C devices?
Probably not given the lack of isolation.
haas anyone manage to get the atc sensor data into HA ? i'm getting the switches and PM from tasmota but nothing from the atc. ty
You could probably do it with Blerry scripting on Tasmota or via Esphome Bluetooth proxy
I'm trying to find the video about that project on the R2, but I can't seem to find it. Can you please share the link?
My hydra video from a couple years ago.
Hello, I am French (translation by google), I wanted to know if it is possible to have: energy today, energy yesterday and energy total for each relay (separately).
thank you
I do not think that is supported in Tasmota but I do know this power monitoring chip is supported by ESPHome as well now.
@@digiblurDIY Merci pour votre reponse et bonne année .
Does Sonoff Dual R3 have an alternative Tx & Rx connection? I have 1 unit with no pads on the plate so I cant use it with Tasmota.
Any advice would help
Yes. The headers on the chip itself.
Is it possible to toggle switches based on BLE sensor data?
Yes, if the sensor is supported but that could also be done via Berry script too.
What was the old video where you did the R2?
The video was actually on a basic that I was doing but fully adaptable to the dual R2. Before I was doing the video thing I did an R2 with a ton of buttons and even used one of the LED traces as an input.
ruclips.net/video/WsatPkC2Hf0/видео.html
Thanks Travis. How is that new desk?
As you can see I made a little modification to it. That black shiny grain top just wasn't going to work well with a camera pointed at. Inadvertently came to the conclusion I'll never have a smooth work bench/desk again. There's no going back.
@@digiblurDIY I hear you. 😊
I want to use the R3 in Home Assistant, i need to flash the firmware anyway and than i can recognize it in HA?
That's what I did as I don't do the cloud thing.
@@digiblurDIY i want to use R3 to open/close a window shutter, so there's a way with TASMOTA to configure it as a motor device? i want that Home Assistant will recognize it like a motor..
tasmota.github.io/docs/Blinds-and-Shutters/
@@digiblurDIY looks like you have an answer for everything! thank you so much
Except for women...
Hi, Which method should I use now to flash tasmota to Dual R3?
What firmware?
@@digiblurDIY The devices will arrive today. Will update once I get them.
Sonoff firmware : E32-2SW-P0 version 1.4.0.
Updates are available. But I did not update it.
The Dual R3 board version is 2.0
I was asking if you were doing esphome or Tasmota
@@digiblurDIY Tasmota.. Sorry for the confusion 😁
Hello, i watch and enjoy your channel. First comment :). I followed this instruction and have 3x Sonoff Dual R3 running at my house and a number of other sonoff devices running tasmota. I found only recently the Sonoff Dual R3 has become very laggy, (All other sonoff devices are going well). I have tried factory resetting, updating to the latest firmware, downgrading to an older firmware but nothing seems to fix it. The symptoms are when a light switch is turned on, 3-5 seconds later the light turns on, Very unresponsive webpage. (Not responding after a few refresh then it might come back). If you have any tips of suggestion it would be much appreciated, It almost feels like the hardware is damaged somehow? thanks Grayson
Welcome and thanks! Using Tasmota?
@@digiblurDIY just an update. I managed to solve this. I ended up replacing to a new Sonoff dual R3 to no success, i then realized the problem must of been somewhere else, Then i looked into my network, Turned out to be only a problem when on that wifi VLAN. So internal network issue, Not tasmota, Thanks
Ahhh...yeah if you block stuff like DNS, NTP, etc they get laggy trying to connect to the time server and/or DNS. Point them to a local service and they will be happy.
Hi, I followed the tutorial and managed to make it work without the power monitoring. I used the Tasmota Template in the description. I have the same rev board as you do. Any idea ?
I would try a reflash? Did you get both relays?
You do need to make sure you flash the latest development version to get the power monitoring like I stated. This bin link works, I just updated mine to it a bit ago. ota.tasmota.com/tasmota32/tasmota32-bluetooth.bin
si i just found out, that i have revision v2.0 where should be used this template: {"NAME":"Sonoff Dual R3 v2","GPIO":[32,0,0,0,0,0,0,0,0,576,225,0,0,0,0,0,0,0,0,0,0,3200,8128,224,0,0,0,0,160,161,0,0,0,0,0,0],"FLAG":0,"BASE":1}
Hallo... Why doesn't use ESP32 on TX Series too?
Not familiar with those.
@@digiblurDIY 😭
Thankyou
Can it do 3-way setups?
Some types yes as it has mains AC on the switch inputs.
Can i use it to switch between mains supply and solar supply as output ?
No. It is not a dry contact relay.
I already have a 2 way switch to do that operation and it works well as of now but it manuel
Capable of stuff like pseudo room assistant implementation?
If you carry around a bluetooth tracker or get one implanted somewhere. DOH!
@digiblurDIY did the ble sensors appear in tasmota integration in Home assistant ? To me the only way was to put so19 1 and then they appear in mqtt integration.
That's the only thing I saw as well as I guess they aren't supported in the integration yet.
@@digiblurDIY ok, but i saw in your previous vídeo (live) that it appears in the integration with an nodemcu esp32 ( or not 🤔). Maybe was other version....
See I was thinking it brought them in too during beta but figured maybe I had it backwards. I need to go check and see what changed.
Tried flashing 4 off R3's, soldering wires onto PCB. One worked. Other 3 'no go" Not sure why. Has anyone had this experience...
I haven't heard of this myself. Faulty USB TTL adapter? The ESP32 does take a little more power.
i just use the pin part of the dupon cable to solder to the pads makes it much easier
Ouch. I usually mention to not do that. It's like gluing a pry bar to a piece of paper.
First
It's painful to see such a beautiful table being used without protection with soldering.
Table top cost a little less than $30 and is intended exactly for this. It was a black kind of faux grain wood, super shiny. Horrible for video cameras with the massive glare. I tried a couple mats but they have glares as well and found these boards and modified my table, I fell in love with the look as well but then one big surprise hit me by accident. I'll never use a smooth work bench/table area again. It's amazing to use for projects and things just grip, don't slide or roll off. Don't worry, I bought extra boards too for replacement needs since they were so cheap at the hardware store.
@@digiblurDIY I understand it was bought for the purpose and as an extra bonus it looks good in the video.
But it's still too beautiful for me to work on.
anyone got power monitors working with esphome?
I haven't seen any movement sadly - github.com/esphome/feature-requests/issues/1151
@@digiblurDIY I went with the shelly 2.5 should be here tomorrow. I need some single switches I might go with sonoff then.
Ear wax for flux... Who woulda thought...
And for the record, I have not tried it yet.
People put this stuff in their house? afaik no sonoffs are UL listed yet are they ? eeeehhh no thanks
It's no longer 1985 McFly. UL isn't what it used to be and even insurance companies can care less about it. Almost as bad as some of these FCC certs you see on products.
First
Hmm...