To prevent oil spilling on mower deck and floor as you tilt the mower, leave the dipstick screwed in until you have the mower completely tipped up on its side. Then loosen the dipstick until the big notches in the threads of the dipstick are exposed allowing the oil to drain out. Do not completely remove dipstick.Just enough to allow the oil to drain. When drained, re tighten dipstick before righting mower. Again, this prevents oil dripping on floor and mower deck. Remove dipstick, wipe clean and re fill engine with oil
@@gabea.2123 Don't feel bad, I spilled oil too before it finally occurred to me there had to be a reason for those big notches in the dip stick threads.
I have a GCV160 on my lawn mower for the last 24 years, it's still running perfectly. Had to replace the deck after about 15 years due to corrosion. Well worth ones while to look after the engine diligently, it'll reward the tlc!
I buy my oil by the 5 quart jug , cost saving that way . But I measure 12 ounces out for my Honda and add a bit more to bring it up to the max level on the drip stick . That's the life of the motor changing the motor oil and always using ethanol free gas .
This mower is perfect for medium to large yards ...I'm on one Acre I use the craftsman for front and back yards and a Earthquake String mower for the open larger part of the yard works out perfect the Craftsman mower has the GCV Honda Engine and the Earthquake String mower has the Viper Engine....Both these engines are some of the very best and will last many years
.58 qt = 18.56 oz. A better tip with the kitty litter,..... after putting it on top of the oil spill, grind the kitty litter in with your foot. That will pulverize the litter, making a powder that further absorbs, and scrubs the concrete. But now the big question. To check the oil, do you thread it in and out each time, or measure by just putting the dipstick into the hole and not threading it in ?
Need to check the manual on how to check the oil level. I believe you don't screw it in then remove to check. You just stick the cover in, then pull it out and check the level.
Thank you for this instructional! My boss wants me to change oil in our pressure washer with the same engine and I couldn't find any drainage valve on the bottom
Fantastic video - thank you! I have a Honda Yardman 160cc that has been sitting for a couple years. I'm going to pull the oil, and thanks to your video, I'll be able to do it much easier! The gas has evaporated - do you think I need to check the carb, or should I be okay? Thanks again!
Ray Parkin If the gas has evaporated, I would check the fuel line and the carb for varnish buildup. If the gad was not treated, the carb might be clogged.
This video played twice reading comments.😅😅 Usually is warm climates for mowing especially in most parts of America. If you live below Washington D.C. on east coast of America it's probably hot in your area during mowing season
I have a Honda GVC160 lawn mower engine and the problem is that is when the engine is running,it acts like it wants to shut off.What i mean is the RPMs keep going down and going back up.Could that be the engine governor? if there is a engine governor,where is it located on this type of engine?
@ Gary Jackson Mine was doing the same. Buy a set of welding tip cleaner/reamers. (Tractor Supply, Amazon etc.) Remove and ream the main jet on the carb. Spray carb cleaner in the carb orifices. Mine works great now!
willy541000 Yes, that is strange. On Honda engines I use 10w30, on Briggs and Stratton I use 30w. 30W especially if you are in warmer climates 90F +. 10w30 will work but might burn a little oil.
It's due to the oil viscosity and weight at different temps. Colder climates use a thinner oil because cold oil is thick at first then thins out as it warms up. Warmer areas use a "thicker" oil because it's already warm, and once again as it runs will thin out. Both situations the oil will be roughly the "same" viscosity..... This is of course in perfect world scenario..... Just a real brief quick explanation... Hopefully that kinda helps....
To prevent oil spilling on mower deck and floor as you tilt the mower, leave the dipstick screwed in until you have the mower completely tipped up on its side. Then loosen the dipstick until the big notches in the threads of the dipstick are exposed allowing the oil to drain out. Do not completely remove dipstick.Just enough to allow the oil to drain. When drained, re tighten dipstick before righting mower. Again, this prevents oil dripping on floor and mower deck. Remove dipstick, wipe clean and re fill engine with oil
I wish I had read your comment an hour ago... I didn't make a big mess but I could have avoided it altogether.
@@gabea.2123 Don't feel bad, I spilled oil too before it finally occurred to me there had to be a reason for those big notches in the dip stick threads.
thanks ! this is going to be my second time , I'm definitely going with your technique- no doubt
Often the comment section is better than the video itself. Thanks
I have a GCV160 on my lawn mower for the last 24 years, it's still running perfectly. Had to replace the deck after about 15 years due to corrosion. Well worth ones while to look after the engine diligently, it'll reward the tlc!
I have a Troy built with the same engine. Going strong 9 years, runs like new. Hondas reputation is well earned
Cool! They will last a long time if you take care of them. 👍👍
I appreciate the guidance on where to examine for signs of overfilling, e.g., by the governor and air filter, good stuff.
I buy my oil by the 5 quart jug , cost saving that way . But I measure 12 ounces out for my Honda and add a bit more to bring it up to the max level on the drip stick . That's the life of the motor changing the motor oil and always using ethanol free gas .
No disrespect brother. But to everyone else tuning is, video starts at 4:00 mark
Thank you.
Thank youuuuuuu
🎶you are the wind beneath my wings🎶
Cut the top off of a gatorade bottle place it on the filler tip with one hand and hold the bottle with the other viola no mess every time
Thank you sir, I have a Troy built but same Honda motor .. Going to change mine when I get home thanks to you . Just picked up my Pennzoil 10W30 🙌
They make a suction pump works great for changing oil in small engines.
This mower is perfect for medium to large yards ...I'm on one Acre I use the craftsman for front and back yards and a Earthquake String mower for the open larger part of the yard works out perfect the Craftsman mower has the GCV Honda Engine and the Earthquake String mower has the Viper Engine....Both these engines are some of the very best and will last many years
Oil should be shecked with the dipstick not screwed in.
So level is just right....not overfilled
That dog is killing me 😂
15w40? Where did you get that?
If you’re just trying to change your oil skip to the three minute and 20 second mark and he finally tells you what to do.
12 to 13 oz according to the Honda manual
.58 qt = 18.56 oz. A better tip with the kitty litter,..... after putting it on top of the oil spill, grind the kitty litter in with your foot. That will pulverize the litter, making a powder that further absorbs, and scrubs the concrete.
But now the big question. To check the oil, do you thread it in and out each time, or measure by just putting the dipstick into the hole and not threading it in ?
On Hondas they say not to thread it in to check the oil level. Usually there's a sticker on dipstick side that demonstrates this book they wear off.
@SBow311 nope - just stick it in. don't screw it in.
Thank u for this video. N thank u for being kind to ur pets. They're awesome !
TJ Yes, they are awesome!
TJ Yes, they are awesome!
They are just like human members of the family, just considerably more loyal.
moto1p1 SO true ! 👍❤️
Thanks for the help ..you are awesome !😊
You don't screw the dipstick in on when you check a Honda lawn mower motor oil so it probably isn't overfilled
Need to check the manual on how to check the oil level. I believe you don't screw it in then remove to check. You just stick the cover in, then pull it out and check the level.
I remember having a sticker on a Honda engine that said that although that was on a Honda brand lawn mower. I suppose the stickers good fall off.
Thank you for this instructional! My boss wants me to change oil in our pressure washer with the same engine and I couldn't find any drainage valve on the bottom
Fantastic video - thank you! I have a Honda Yardman 160cc that has been sitting for a couple years. I'm going to pull the oil, and thanks to your video, I'll be able to do it much easier! The gas has evaporated - do you think I need to check the carb, or should I be okay? Thanks again!
Ray Parkin If the gas has evaporated, I would check the fuel line and the carb for varnish buildup. If the gad was not treated, the carb might be clogged.
This video played twice reading comments.😅😅 Usually is warm climates for mowing especially in most parts of America. If you live below Washington D.C. on east coast of America it's probably hot in your area during mowing season
thanks for this
4:56 Dog supervision!
They know everything, even though they act dumb.
Oil is the first thing you should check.
Will 5w-30 work?
Yes
Lol I thought that was a land mind from your dog
Thanks man
Thank ya 🤘🏼
👍👍
12-13.5 fl Oz of 10-30, boom, saved you 11mins
I have a Honda GVC160 lawn mower engine and the problem is that is when the engine is running,it acts like it wants to shut off.What i mean is the RPMs keep going down and going back up.Could that be the engine governor? if there is a engine governor,where is it located on this type of engine?
Gary Jackson I would check the carburetor first. It could need a good cleaning.
The DIY Tool thank you
Thanks
@ Gary Jackson
Mine was doing the same. Buy a set of welding tip cleaner/reamers. (Tractor Supply, Amazon etc.) Remove and ream the main jet on the carb. Spray carb cleaner in the carb orifices. Mine works great now!
Also saw it could be the gas cap isn't venting properly
good helper
Thanks! I hope it helps.
Should've done the job on the grass, I would've save your concret
You're Brendel He's handsome Our precious we had to put her down she was 13 years old look just like him but the girl version🥲🥲🥲
Good video but it would have been even better if the dog hadn’t been blocking the view for part of it.
The dog is the star of the show.😊
my husqvarna with Honda gvc 160 recommends sae 30 over 32F and 5w-30 under 32F. Not sure why different since they are same motor.
willy541000 Yes, that is strange. On Honda engines I use 10w30, on Briggs and Stratton I use 30w. 30W especially if you are in warmer climates 90F +. 10w30 will work but might burn a little oil.
I live in Lafayette,Louisiana and the weather is hot almost all year round.Is using 10w30 ok to use on my Honda GCV160?
It's due to the oil viscosity and weight at different temps. Colder climates use a thinner oil because cold oil is thick at first then thins out as it warms up. Warmer areas use a "thicker" oil because it's already warm, and once again as it runs will thin out. Both situations the oil will be roughly the "same" viscosity..... This is of course in perfect world scenario..... Just a real brief quick explanation... Hopefully that kinda helps....
@@disrespectz question is... how often are lawnmowers used in the cold 🤔
Some regions have colder temps and cool season turfs thrive in, meaning mowing at colder temps.
You forgot to put cardboard under your oil collection container.
I use plastic bag, it never mess floor.
okie way of changing oil you did make a mess .....Im looking for a tube to insert so you don't dump oil all over the concrete
Thanks for the video but it doesnt take 11 minutes to show it. Some people like to hear themselves talk.