etrailer | Feature Review LED Mini Side Marker and Clearance Light

Click for more info and reviews of this Optronics Trailer Lights:
www.etrailer.c...
Check out some similar Trailer Lights options:
www.etrailer.c...
www.etrailer.com
Don’t forget to subscribe!
/ etrailertv
Full transcript: www.etrailer.c...
Hello neighbors, it's Brad here, at etrailer. And today, we're taking a look at installing the Optronics mini LED 3-diode clear lens with amber light. And this is gonna be a great option for updating your trailer with some nice LED lights. And it's gonna be completely submersible, so it's gonna be great for your boat trailers as well. Now, this is an obvious upgrade compared to what we had on here. Not only is the footprint smaller, but the light is absolutely better.
And being LED, it's gonna be more efficient overall. Taking less energy to give us that brighter light. Another benefit of the LEDs, is you have the diode there. So, with incandescent bulbs, as you're kind of bouncing around down the road, as trailer's can do, that bulb has got those small filaments that can break over time, and you have to change out the bulb. Well, that's not the case here with our LED.
The lifespan of these is significantly longer than your normal incandescent bulb. Now, when not in use, this is a clear lens. And it's gonna be a polycarbonate, so it's gonna hold up really well. It's extremely durable. That way, if, you know, little rocks or whatever hit it, it's not gonna chip.
These are great housings here. And that's gonna house our three LED lights that give us 180 degrees. Giving us a beam pattern that's able to be seen across the board. So, we mount it on that flat surface, that 180 degrees will be easily visible. And the great part about this, is it has a single wire.
The grounds integrated on the mounting point. So really, it's just one wire that you're tying in to your running lights. And other than that, it's gonna be an easy replacement, or addition, to your trailer. Now, having some clearance lights like this one that's burnt out, it's a good time to not only replace, but upgrade. And really, lighting has come such a far way. LEDs are wonderful, they're very efficient, and they put off a really good light that these incandescences just can't keep up with. So, it's a good time to replace this with a nice LED version. So, I'm gonna go ahead and get this old one off and then I'll show you how to get our new one in and wired up. Now, we have our existing hole and that's how it mounted up. So, we're gonna need to drill two holes. We can use this existing one to pass our wire through. And the way I'm gonna do this, is just make sure that I have it nice and lined up here. And what I'll be doing is using the one side that doesn't have this ground. That way, we're not gonna damage this ground plate. So, pretty easy. We'll just go ahead, get this in place. And its going to be hard to get a marker, you could probably get a pencil in there, or something along those lines to make the mark, but I'm gonna just take a very small drill bit and kind of make some pilot holes here. If you have a punch, that'll work as well. And then what I'll do, so I don't have to use that ground, I'll just line this one up, and then make my drill on the other side. And then what I found, is the holes here are gonna be about perfect for a 5/16 drill bit, or 5/32, I'm sorry. And that 5/32 allows for our hardware to pass through. Now, it doesn't come with hardware, so you are gonna want to pick some up. We found some 8/32 stainless hardware with some washers and locknuts that's gonna do a good job of mounting this up. But I'm gonna go ahead get our holes drilled in, and then we can mount this. And obviously, before drilling, make sure that you don't have any wiring behind there that you could potentially damage. Now, these are really, really nice because they ground as you mount these to a metal frame here. But, we're gonna want to make sure we have a really good ground, so part of that is gonna be grinding down the surface. So, one of these, you're gonna want to make sure it's nice and clean and smooth, that way we have nice, clean ground. So, you can use Scotch-Brite or some sandpaper. Either way that's gonna work well. I'm just gonna throw a quick grind on it here. And then, now we can pass our wires through. Make sure our ground goes on that edge there. And with your hardware, go ahead and get this mounted up. Now, I'm using a washer here, to give it a little bit more, a little bit more protection. That way if you over-tighten it, at least that washer's gonna kinda disperse that pressure there and it doesn't crack our light. So, I'm gonna go ahead and put a flat washer and then a split washer here, before putting our nut on. And that's gonna allow this to kinda, hold in place