speed control of BLDC motor using PID controller

Поделиться
HTML-код
  • Опубликовано: 16 янв 2025

Комментарии • 67

  • @nsangalashi
    @nsangalashi 8 месяцев назад +6

    In the decorder circuit, the second wire connected to the second input demux should be connected behind the NOT gate and not in front of it, the gain should remain the same, 30/pi

  • @HarshT-dn5ug
    @HarshT-dn5ug Год назад +11

    in order to get exact result put the value of dc voltage to be 47.89v and the value of gin to be kept to -30/pi good luck
    ✌✌

  • @alikoca5711
    @alikoca5711 4 дня назад

    How did you find PID parameters? Can you explain?

  • @SelwynLloydMTado
    @SelwynLloydMTado 10 месяцев назад +1

    Hi! May i ask how to get the value of kp,ki, and kd?

  • @stukershaw8394
    @stukershaw8394 2 года назад +2

    Hi could yu tell me where this truth table comes from as my model won't work as yours does, sure it's to do with truth table?

  • @thoughts424
    @thoughts424 Год назад +1

    Hi! It was helpful. Can you provide the source for truth table of the decoder used or any more sources to know about decoder used in BLDCs.Thanks!

  • @kartik_kumar13
    @kartik_kumar13 2 года назад +1

    don't put -30/pi instead of 30/pi. just change NOT gate at 27:34 . only apply not gate to upper wire don't apply on both the wire.

  • @RayanMalik-ql2yj
    @RayanMalik-ql2yj 8 месяцев назад

    Very useful video! Thanks a lot, and good luck!

    • @tejassrivastava6971
      @tejassrivastava6971 8 месяцев назад +2

      Did you simulated? Did it work?

    • @FLAMERAYYT
      @FLAMERAYYT 8 месяцев назад

      @@tejassrivastava6971yup! It worked

  • @danielteodoro8254
    @danielteodoro8254 2 года назад +3

    why you didnt change the PID parameters?? What kind of methods did you use?

  • @takedowntheccp.5167
    @takedowntheccp.5167 3 месяца назад +1

    thank you very much. this the viedo help me study. 感谢!

  • @gowtham3120
    @gowtham3120 Год назад

    Mam How did you paste that truth table there? 27:34

  • @mustaphaaguerrab803
    @mustaphaaguerrab803 Год назад

    please any help how she did to get the PID values ?

  • @kannupriya8957
    @kannupriya8957 7 месяцев назад

    Hi mam the video is very useful but what's the logic or truth table you are following to make a decoder at 23:04

  • @HARSHAPOWER-xe6dx
    @HARSHAPOWER-xe6dx 2 года назад

    You are trying to do in future you will get succeed keep go on

  • @steffinchackovarkey5773
    @steffinchackovarkey5773 2 года назад

    Which version of MATLAB are using

  • @techvik63
    @techvik63 2 года назад +2

    Decoder circuit how to add truth table

  • @aravindsomanath2485
    @aravindsomanath2485 2 года назад +8

    I tried,but I couldn’t get the result as you got.I think some changes you made which is not included in this video.

  • @nithishs6444
    @nithishs6444 Год назад

    How do you import the truth table value into the model.

  • @MarripudiSarathbhargav
    @MarripudiSarathbhargav Год назад

    Then how when we remove the pid then the result can provide please

  • @nafreefirenaistam8267
    @nafreefirenaistam8267 2 года назад

    Can you do this with dc servo motor?

  • @Tamana004
    @Tamana004 2 года назад +5

    For all those who aren't getting the right output.. Keep input dc voltage low upto 47v and keep the gain block value -30/pi instead of 30/pi...this way you will get the output as 499.5

    • @rohanmistry7528
      @rohanmistry7528 2 года назад

      Do you have the simulation

    • @abdulmanaf4963
      @abdulmanaf4963 2 года назад

      thanks alot bro its working😍

    • @rohanmistry7528
      @rohanmistry7528 2 года назад

      @@abdulmanaf4963 do u have the simulation sir

    • @sunilsahare8917
      @sunilsahare8917 2 года назад

      if we put -30/pi instead of 30/pi it works in matlab but is it feasible in while going for hardware work, will be useless

    • @ashishshah1856
      @ashishshah1856 2 года назад

      thanks a lot

  • @yshashi5920
    @yshashi5920 Год назад

    Do u have base paper ? Can u send the base paper link..

  • @Prasannaveera-x2j
    @Prasannaveera-x2j 11 месяцев назад +1

    podu maja than inimae ithan yen final year project uh....

  • @arpitsharma2324
    @arpitsharma2324 2 года назад

    how you choose the value of gain .

  • @snehasishbanerjee4705
    @snehasishbanerjee4705 2 года назад

    To all, who are not getting desired output... Its decoder subcircuit is a complete mess, that's why it's not working... Get a right decoder circuit for Hall sensor anywhere from Google.. the circuit will run nicely.... After that, you can change the parameter values of PID CONTROLLER to get better response. All the best😊.

    • @malisiri3883
      @malisiri3883 Год назад

      can you give the PID controller values

  • @rohanmistry7528
    @rohanmistry7528 2 года назад

    Can i get the simulation

  • @saravanakumar.a
    @saravanakumar.a 5 месяцев назад

    Invalid setting for input port dimensions of 'BLDC/gate pulse/Demux'. The dimensions are being set to 1. This is not valid because the total number of input and output elements are not the same
    Component:Simulink | Category:Model error
    Error in port widths or dimensions. 'Output Port 1' of 'BLDC/gate pulse/emf_abc' is a one dimensional vector with 1 elements.
    Component:Simulink | Category:Model error
    These were the two errors poped up for me. Could you pls mail me the solution regarding it please :)

  • @adityakale9917
    @adityakale9917 Год назад

    Mam plz share the simulation link...

  • @vrinda_theambitious
    @vrinda_theambitious Год назад +1

    Keep gain block gain block value -30/pi and correct the decoder circuit from ruclips.net/video/irBoN1RJkO4/видео.html. The Second line should be connected to not gate input instead of output.

  • @supraxmen125
    @supraxmen125 Год назад

    I don't have the correct output even I edited it. Can someone tell me about the value of PID, Sine Wave, and repeating sequence? Thanks a lot guys 😁

  • @walmirsantos9026
    @walmirsantos9026 2 года назад

    I tried too, but couldn´t the result as you got. Walmir Brazil

  • @KrzysztofDomagaa-ym8zn
    @KrzysztofDomagaa-ym8zn 9 месяцев назад

    Can you send me a files?

  • @PratheekPoojary-it8us
    @PratheekPoojary-it8us Год назад

    👍

  • @zanakemaloglu1755
    @zanakemaloglu1755 2 года назад

    same paremeters are missing, ı coundt get the result

  • @techvik63
    @techvik63 2 года назад

    Mam please tell me fast tomorrow test

  • @hocho2278
    @hocho2278 2 года назад +5

    What is the purpose of sharing this videos 🤣🤣🤣🤣🤣🤣🤣🤣Thank GOD, If you don't want to share the values of PID, Repeating sequence 😅🤣Many undergraduate students are watching and wasting their times.

  • @engineersdotcom3446
    @engineersdotcom3446 2 года назад +1

    results are not matched when i am trying to make its simulation

  • @naemamir678
    @naemamir678 Год назад

    This video is waste of time

  • @jakkavijayalakshmi3012
    @jakkavijayalakshmi3012 2 года назад

    I tried too much .but I didn't get output.How to contact you