Unknowingly I took the front pass seat out ... and turned the ignition on. Gave me this same code. Fortunately I have a better scanner at work. I could go into the body control module and reset codes in the restraint system. I have a 2012 JCW hardtop
This is the exact information in looking for but your seats have a dofferent connector than mine do. Any chance you chould show me how this is done for the 2013 model? Its one big yellow connector instead of two small ones
You should always disconnect the negative first, that way it wont spark when you reconnect or bridge a tool to ground and you also wont spike the sensitive electrics
Hi mate. Great video!!!. Can you do one that explains the dash please. Got my self one of these but need some help explaining some of the dash and buttons?
Thanks guys, worked out well when changing seat. The Brandgarage wanted 1700 Euro to solve this and recomended me to scrap the car (Cooper 2001 in perfect condtion)... :-(
Hello! I own a MINI Cooper -2002. I want to remove the airbag on the passanger side, or at least make the light go off as it´s constantly on. Can I just find the wire and pull it? Just like that?
Hi there, do you know what to do with the heated seat/ weight sensor? Any bypass kit online will only come with the bypass connectors for the seat belt pre tensioner, and the airbag. Thanks
hello, unfortunally i removed the right front seat before disconnect the battery, now the airbag signal light is on, do you know if i have no other choice to go to my mini dealer? thank you
Unknowingly I took the front pass seat out ... and turned the ignition on. Gave me this same code. Fortunately I have a better scanner at work. I could go into the body control module and reset codes in the restraint system.
I have a 2012 JCW hardtop
This is the exact information in looking for but your seats have a dofferent connector than mine do. Any chance you chould show me how this is done for the 2013 model? Its one big yellow connector instead of two small ones
Why should you not go driving around like that? What would happen?
Thanks to your videos I did some works on my mini by myself. Thank you. Great job!
You should always disconnect the negative first, that way it wont spark when you reconnect or bridge a tool to ground and you also wont spike the sensitive electrics
I have a question where you can find a little fuse you connected to the cable
Hello, Can you help me with a doubt? I'm trynign to fix my release trims, how can I replace release trims for mini sport seats?
Great job!
2..2 ohm red red gold gold on a 4 band is 2.2 ohm
Hi mate. Great video!!!. Can you do one that explains the dash please. Got my self one of these but need some help explaining some of the dash and buttons?
How did the new year's resolution work out for you? LOL Was it okay? 😉
Merci ça a fonctionné sur ma mini one r50 j ai mis Les résistances par contre j ai passé la valise
Ça me rassure, je vais tester sur la mienne du coup. Ça a marcher du premier coup ? Pourquoi tu l’a passer à la valise en plus ?
stadixisnotagamer bahh écoute lorsque j ai mis les résistances ça ne s est pas éteint j ai passé la delphi et le défaut je l ai effacé
@@1000RXR Bonjour, pouvez vous me dire quelle résistance vous avez utilisé ?
@@elodiedubois5119 je crois 2ohm
Thanks guys, worked out well when changing seat. The Brandgarage wanted 1700 Euro to solve this and recomended me to scrap the car (Cooper 2001 in perfect condtion)... :-(
Cool - this is why i love the internet !
Hello! I own a MINI Cooper -2002. I want to remove the airbag on the passanger side, or at least make the light go off as it´s constantly on. Can I just find the wire and pull it? Just like that?
hi, wich is the correct resistor? any special condition? i put a 3.9 ohm 1/4 watt with 5% tolerance and doesn't can you help me plis
Works wonders! Thank you for saving me money!
You're welcome!
Did you have to use to remove the code. As I tried this and didn’t work. Any links for the resistor you brought?
My R60 has a main plug yellow, with 2 other smaller plugs. do you know how to do it ?
Can you use a higher or lower ohm resistor? Say a 1.5 or a 3 ohm resistor?
I guess so - but not sure ...
Thank you again!
So I would solder the wires to each end of the resistor correct? Great vid thanks!
Hi
This is correct
powerfulukltd thank you again!
And how to remove the recliner cable?
in my car I have the black connector what is that for?
It’s working on a 2012 Mini Cooper s ??????????
Hi there, do you know what to do with the heated seat/ weight sensor? Any bypass kit online will only come with the bypass connectors for the seat belt pre tensioner, and the airbag.
Thanks
wo kann Ich diesen widerstand kaufen
cooooool with this work on a R56 2007 mini S?
*great tips*
I would retrofit seats with airbags and tensioner if my MINI would not have them - I really don't get why people would take that out.
Would this work to remove an existing airbag warning light for the seat airbag?
Yes adding the resistor - then you need to clear the stored fault
hello, unfortunally i removed the right front seat before disconnect the battery, now the airbag signal light is on, do you know if i have no other choice to go to my mini dealer? thank you
@@audreyr7484 I did same, but how u reset it fault ?
Hi I have just tried this with the airbag seat and the and the airbag light will not go off have you got to do the tensioner as well
@@audreyr7484 hi did u ever find a fix for this?
Hello
Can you say me Value of this componant?
Yes i think it was 2 Ohm.
What error codes do you get with a bad seat belt tensioner
Welche diode ist das ?
2 ohm
Hi, 2 ohm resistor with ......watt ?
0.5watt or higher would be fine
Hi,ive got 2.2 ohm with 0.6 watt , is this ok or should be like yours ?
you should be OK with that i recon.... but clearly i have not tested that so cant be sure 100%
Thank you mate.
@@L663 in your video i see a 3.2 ohm resistor. ? Oranje, red, gold.
What year car is this?
He said it was a 2003 (R50)