DIY Arduino Multi-function Energy Meter
HTML-код
- Опубликовано: 16 сен 2024
- JLCPCB:
$2/5pcs 2Layer & $5/5pcs 4Layer
PCBs: jlcpcb.com
----------------------------------------------------------------
In this video, I will share with you how made a Multifunction energy meter by an Arduino Pro Micro and Current sensor INA 219. The device can be used to measure the following 6 parameters
* Voltage
* Current
* Power
* Energy
* Capacity
* Temperature
--------------------------------------------------------------------------------------------------------------------------------
Instructables Link: bit.ly/2OsvL4u
--------------------------------------------------------------------------------------------------------------------------
🔴 Download Schematic and Arduino Code: www.opengreene...
---------------------------------------------------------------------------------------------------------------------------
Materials Used
1. Arduino Pro Micro: amzn.to/3cTwju3
2. Current Sensor INA219: amzn.to/30wojMM
3. OLED Display: amzn.to/37kKU0g
4. DS18B20 Temp Sensor: amzn.to/2YpoYgl
5. Perforated Board: amzn.to/2YnSt27
6. Screw Terminals: amzn.to/37kuNzI
7. Resistor 4.7k: amzn.to/37kuPHQ
8. Slide Switch: amzn.to/2XOUiX0
9. PCB standoffs: amzn.to/3dTKPD8
10. 22AWG Wires: amzn.to/2XOZWZa
---------------------------------------------------------------------------------------------------------------
You can follow me :
🔴 Instagram id link - / opengreenenergy
🔴 Facebook page link - / opengreenenergy
🔴 Instructables Link - www.instructabl...
🔴 Website Link - www.opengreene...
-------------------------------------------------------------------
About Music Track:
Track Name: Cinematic Documentary
Music by AShamaluevMusic
Show!!! Muito bom!!!! Continue assim, sempre evoluindo seus projetos!!! Top sensacional
Maybe you could expand this to monitor every solar panel on a rooftop, and use a wifi connection to transmit the data to a phone application. Also, a battery charging circuit would be useful.
Awesome
Sir can you design ebike BMS diy
Thank You. I have not much experience on that, but in future I will try to do it.
is there a modified code for using the acs 712 - 30A with a dc voltage sensor ??
Interesting project, it seems very similar to GreatScott's energy meter. One question, what is the purpose of the temperature sensor? Just to see the ambient temperature? At first I thought that the readings were off, but you are from India, right? Pretty hot right now there :) Keep up the good work.
Thank you .
You are correct, temperature sensor is for ambient temperature. I am from India.
Very well done project. You have inspired me to build one and to subscribe to your channel. Thanks for sharing and please share more.
Excellent bro👍👍👍
Thank you bro.
Can you help me to make your previous project ( battery capacity tester ver 2.0)
Because i am a beginner in arduino and programming so i am facing problem during programming of arduino
Sure.
@@opengreenenergy thank you, but how i contact you 🤔
@@ziyaulhaq1301 opengreenenergy@gmail.com
Good work.... Please make monitoring system to my 1.5kw solar off grid .24v batt.
hi, interested to know how to measure AC power in KW and energy consumed in KWH. for load upto 16A. I see many just use current transformer alone. but for AC power need to know actual voltage and power factor to get accurate power reading
I will make a video on AC power measurement in future. Keep in touch
Good work. I am trying to monitor my 12v valence batteries that has 4 module in series at 3.65v each which is = 14.6v. Since these batteries have an internal bms, which has an amp connector. How can I monitor each module using arduino, rs485, logic level converter and 4 module relay? Or is there another way? Please help
I will make a video how you can remotely monitor the parameters from your smartphone.
Open Green Energy will it include all the ingredients I listed?
How about if you wanted a bigger ampere like 10A to test solar panel?
What changes are required if you need to measure upto 100 volts DC and upto 10 amps dc
I am getting around 1 volt and some readings without placing any IO devices. Any help ?
Does this device used to monitor capacity of LFP battery pack of 72V,100A while charging and discharging??
Why is the value for mA, mW, mAh, mWh negative when I hook it up to a solar panel?
Bro I'm using lm35 temperature sensor with nano but there is no change in value is shows -256°
Can you plz help
And my i2c connection work with analog pins not digital
LM35 is not a i2C sensor I think. Please check the datasheet.
@@opengreenenergy ok bro
how can i build a system and connect 15 samples of MFC (microbial fuel cell) in same time for measuring current (low between 0mA to 3A) and voltage (between 0mV to 800 mV) continuously? I have an oscilloscope, if the system help me to get the reading continuously from the oscilloscope or independently measure them, both way is good for me. Please someone help me..
Hi! This is a great project so I'm going to make this, Can you teach me how to put those codes? I'm just a beginner tho
ina219 just 3.2A maybe can use acs712/714
Yes ACS 712 can be used
Hello brother IAM facing a problem ...they show me input voltage as o.30 ,,not exeding 0
Measure the Vcc voltage and calibrate accordingly
@@opengreenenergy that was solved but now the current and power changing ....not stop on fix points
@@opengreenenergy can you help me
Hi Buddy. Youre is nice project.
But arduino Pro Micro take also Arduino Leonardo program uploading why?
Hi can i use lm35 ? And i have suggestion to add a timer
Yes you can use. You have to modify the code to fit into the my code.
Круто. Спасибо!
Sir me NIA219 ki jaga ACS712 use kar sakta hu
Technically yes.
But acs712 is only measures current, to measure voltage you have make additional circuitry.
The code will not work , you have to modify the code too.
Nice bro max current and voltage range?
Thanks
Current - 3A
Voltage - 26V
Can I use Arduino uno
hello sir, i had problems with the voltage seems like it doesnt read the right voltage sir the busvoltage and the load voltage are the same and when i tried looking in the multimeter it wasnt the same on the monitor and the voltage varies like at one point it become 5v then 0.12
yes
What is the voltage range?
I have made it but there some problems
Plz add hindi caption
Plz help me
Instead of pro micro
mWh counting wrong he bro 🥴
Hi iam going to make this
But i dnt understand to which pins load and source is connected