USBASP CHIP ENABLE ERROR - FIRMWARE UPGRADE SOLUTION
HTML-код
- Опубликовано: 6 фев 2025
- This video explains the ways to upgrade Firmware on USBASP , programmer generally used with AVR / 8051 ICs.
Arduino UNO can be used as programmer or another USBASP can be used .Both ways are explained.
Errata :
@4:33 Pin 13 should go to SCK (NOT RST)
AVR DUDES :
blog.zakkemble....
usbasp Firmware :
www.fischl.de/...
USBASP Driver :
protostack.com...
PROG ISP :
exploreembedded...
This guy understands very well about microcontrollers, your site helped me. I was having the problem "chip enable program error" with Usbasp and I got the solution in your site. Good job my friend. You are helping us. From Brazil
Please correct the following @4:31 Pin 13 should go to SCK (NOT RST) The video is very helpful thanks for sharing!
Yes, you are right.Thanks
Dear air my usb asp as same problem can I sent to u to recover plz sir reply me asap
Should the fuse byte High be C9? as SPIEN cannot be set by ISP
USBAsp latest firmware not working on 89S51. But working on other chips (Atmega 8- Atmega328....) I can't fix
This program uploadind youer setted high fuse is wrong. So the atmega 8 not working. Youer fuse hex value disable the USBASP. How to enable the fuse tell me.
Sir my avr chip is atmega8A can this process work on it?
Sir atmega8a or atmega8 ki firmware ki usbasp kihexfile same Hoti h ya alg agr
alag hotii h to plz reply me link bataea kha se milegi
Bhai same problem. Iska answer mila?
Haven't tried it yet but thanks for the good video! The others are way to complex doing it from the Windows command line and changing windows command lines in the directories etc. etc. When I get time I will have to try and program the two USB ASP units I have. Arduino seems like the best operation as I have used it to flash a new program to a ham radio transmitter without setting the fuses or altering the boot loader.
Pin 10 & 13 goes to RST?
Excuse me sir,,, i have to upload the firmware to usb asp,,, but when i try to use it with prog isp, always "CHIP ENABLE ERROR" ,,,,,, whats wrong??? Please help
Even I'm experiencing this. Any idea??
제가 아는 한 해결이 안되는 Vendor ID 오류.....
제가 아는 한 해결이 안되는 Vendor ID 오류.....
새로운 CIP을 사용하면 Vendor ID 오류나는 것은 당연한 것 같구요.
통상 Vendor ID는 Driver 설치 한다고 되는것 아닌것으로 알고 있구요.
저의 경우 usbtreeview 을 사용해 보았지만 결국 알 수 없는 장치로 인식되더라구요.
혹시 해결 방법을 아시면 저도 정말 알고 싶네요..... ㅠㅠ
참고로 수십수백만원의 유료로 발급받는 USB VID PID List 꼭 다운로드 받아보시길... 과연 우리가 보는 동영상은 진실인지 거짓인지 밝혀주시길...
CH340K_USB_Serial_Programmer_Prototype ( CH340K AVRISP Prototype Creation Completed )
CH340K_AVR_ISP ( CH340K_USB_Serial_Programmer_Ver1.00 )
CH340K_USB_Serial_Programmer ( CH340K AVRISP Download Test_Successful )
ruclips.net/video/23rIH0WQGkU/видео.html
CH340G_AVR_ISP ( CH340G_USB_Serial_Programmer_Ver1.00 )
ruclips.net/video/z29Z8-oaNt4/видео.html
FT232RL_USB_Serial_Programmer_Prototype ( FT232RL AVRISP Prototype creation completed )
ruclips.net/user/shortsGYJS996cfQc
FT232RL_USB_Serial_Programmer ( FT232RL AVRISP Download Test_Successful )
ruclips.net/user/shortst5o48-osJpc
Useful video 👍
Sir ,I did the same thing as you said and I soldered pin 1 and pin16 and yet its showing error that there is 'unknown signature 000000'
What to do sir and the resistor I used is of 240k ohm
Not 420 k u use 270 ohm resistor
240 work nhi kareg aap 270 ka use karo chip signature error nhi aayega
Plz provide ur phone number
How to load bootloader on atmega8A and atmega328
My 89s52 programming success with arduino isp but not work with usbasp
Im update 2011 firmware for usbasp
Hi how are you thank you so much for this explanation can you help me making a programmer and uploading the hex file to atmega8
Muy bueno ,Muchas Gracias !!!!!
I have follow your steps and update successfully, but after that USBAVR cannot detected by computer.. 🤭
제가 아는 한 해결이 안되는 Vendor ID 오류.....
새로운 CIP을 사용하면 Vendor ID 오류나는 것은 당연한 것 같구요.
통상 Vendor ID는 Driver 설치 한다고 되는것 아닌것으로 알고 있구요.
저의 경우 usbtreeview 을 사용해 보았지만 결국 알 수 없는 장치로 인식되더라구요.
혹시 해결 방법을 아시면 저도 정말 알고 싶네요..... ㅠㅠ
arduino pin13 - sck target
avrdude.exe: Device signature = 0xff0000
avrdude.exe: Expected signature for ATmega8 is 1E 93 07
Double check chip, or use -F to override this check.
avrdude.exe: Device signature = 0x800000
avrdude.exe: Expected signature for ATmega8 is 1E 93 07
Double check chip, or use -F to override this check. dupa ce am pus pin13 la SCK.
avrdude.exe: Device signature = 0x000000
avrdude.exe: Yikes! Invalid device signature.
Double check connections and try again, or use -F to override
this check.
avrdude.exe done. Thank you.