Unite UB-1100 Wheel Balancer final cut Installation Operation(0728)
HTML-код
- Опубликовано: 2 окт 2024
- Unite UB-1100 Wheel Balancer final cut Installation Operation
Unite Automotive Equipment LLC
www.unitequipme...
*Advanced international standard merging the best of industry
Absorbing advanced technology
*Own research and development, property rights and guarantee the high quality service
1.High precision main shaft with strict heat treatment process makes sure repeated measuring accuracy
2.High stable and high accurate computer chip. With self-calibration and self-diagnosis functions
3.LED light & Digital display
4.With 5 balancing modes and OPT function. Extended measuring scale can measure rims from10” to 24”
5.Equipped with protection hood,plier,full sets of cones and caliper
6. With standard automatic braking system, make operation much easier
7.With optional brake pedal for accurate positioning of counter weights
8.With optional larger cone and spacing ring, machine can balance rim with big central bore such as that of Toyota coaster,Transit, Iveco etc.
9.With optional universal flange adaptor,machine can balance,French cars'tyres such as that of Citroen
10.High accuracy for the balancer, guarantee high quality service
11.Easy and safety operation
~-~~-~~~-~~-~
Please watch: "Car Lift Installing Scissor Lift -Unite U-C45 Wheel Alignment Scissor Lift with Rolling Jacks"
• Car Lift Installing Sc...
~-~~-~~~-~~-~
عملية ضبط الماكينة لما تكون 0000
Hey! Err -1- 😢 what this means?
Code:Err 1
Meanings:Main shaft not rotate or have no rotate signal
Cause:
1.motor fault
2.position sensor fault
3.power supply board fault
4.computer board fault
5.connection-peg untouched
Remedy:
1.change motor
2.change position sensor
3.change power supply board
4.change computer board
5.check cable connections
Ouais super cool rien a dire j'aimerais bien apprendre plus
Please email to sales05@chinapuli.com for a solution. Thanks.
Ses a combien on peu payé cette apareil
Thanks for getting in touch with us on Messenger. Please send us any questions you may have or email to: Rebecca: sales05@balancer-sh.com
How to choose the mode of S/1/3
Sir if machine is showing ERROR 5 what will be the problem sir pls reply as soon as possible
ERR.5:
Open protection before beginning launch
CAUSE:
a)Open protection
b)Faulty protection switch
REMEDY:
a)Close the protection
b)Replace the switch
Simple super
Comment reconnaitre la position exacte d positionnement de la masse d'équilibrage pendant l'équilibrage d'une roue
How to reset
How do you calibrate this machine?... I Have an Error 8 at end of self calibration .... What is means Pls?
I'd been did this steps as shone in this video but in the end always get Error 8 .. can you help me? even someone sent to me that there are fault in power card and needed calibration.
I'd been finished....
But I have a comment on the issue...
The fault was the screen card and the agent was replaced it without knowing the basic cause of problem... which is some solt on the solder connective boints need to clean.
Please email to service@chinapuli.com and Mark: from youtube. Our sales engineer will give prompt support.
how do you calibrate this machine
How much for machine
Please email to sales05@chinapuli.com for a solution. Thanks.
الحديد تطيح مع الوقت لازم تبديل تاير
Error 5 please help
Error 5 means the Protection hood does not lay down, if not , please check whether the microswitch of hood has problem
watched many types of machines and balancing, but my question now is can you balance a wheel dynamic and static balancing at the same time to have a best job ? If not why ? What is the difference ?
Thanks for your reply.
You can only do one or the other. Static is single weight in center. Dynamic is a weight on each side of the wheel.....
James Malone
My friend thanks for your reply ... but I don't know why some videos showed that dynamic does both calibration together vertical and horizontal, whereas static is only one type... even in some machines you can see illustration of the weights in sides of a steel junt t indicate static calibration ... and not in the center of the wheel... very weird !!!
Went putting my machine on I hear a beeping sound and don,t work what what wrong
I need the bottom circus board.
Simple Good
Please email to sales05@balancer-sh.com. Our sales engineer will give prompt support.
السلام عليكم عند وحد مثل عاطلت
3etini nimero ta3k
One piece
One piece price
Please email to sales05@chinapuli.com for a solution. Thanks.
I have eror 10! Please help!!!
i think this model doesn't has error 10
20g kér a külső oldalra a csávókám meg 30 rak és jó!:D