Hello Friends अगर आप हमारे चैनल पर नए हैं और ऐसे ही जानकारी वाला वीडियो आगे भी देखना चाहते हैं तो कृपया चैनल को Subscribe और वीडियो को लाइक कीजिए ताकि अगली वीडियो का नोटिफिकेशन आप तक पहुंच सकें धन्यवाद
Oh bhai you set the dial on top side on zero how can possible to .01 after rotating, it's called run out, apko top pr jahan dial 0 set kia hai mark kr laina chaye and again hub ko exactly usi point Lana chaye to yeh 0.01 ka difference nahi aye ga 0 reading he aye ga. Or how can you alignment without adjusting axial?
Sir Bearing ka inter clearance formula kya he, or master levels former kya he, or spring couplings ka misalignment kitna tak chod sakte he sir. Plz replay comment sir. 🙏
Hi boss i am shahin form bangladesh boss i whant to learn something about dial gauge from you if you teach dial gauge has to small and big cuts like watch tahnks boss
Iccead frame ko half grouting karne ke baad hi master level kiya jata hai pump ke suction pe master level ko rakh kar dekhen aor base bolt ko tight karen aor frame ke base me leveling ke according shim bhi dena padta hai taki trolence me hi rahe
@@Naturelover.21 before adjust the gap between motor and pump, first you must check the coupling spacer size or you said coupling size usky size ky mutabik ap size rakh sakty ho, and agar spacer kay sath shims Hain ya phir gasket use hoti hai uski bhi thickness add krna prti hai
Muhammad shoaib ek baat batao agar right side me reading 0.03 hai toh same hum same side me frame ko hammer kar k zero le ate hai mujhe ek doubt tha ki frame aur foundation me bolt laga hai toh motor age kaise jata hai
Hello Friends अगर आप हमारे चैनल पर नए हैं और ऐसे ही जानकारी वाला वीडियो आगे भी देखना चाहते हैं तो कृपया चैनल को Subscribe और वीडियो को लाइक कीजिए ताकि अगली वीडियो का नोटिफिकेशन आप तक पहुंच सकें धन्यवाद
Ye motor maintenance ke liye Kiya jata hai ?
Very Helpful..., Thanks a Lot
बहुत सुंदर जानकारी दिया है आप ने आगे रिभर्स इलाइमेंट का थ्यूरी भी बताइये प्लीज
Oh bhai you set the dial on top side on zero how can possible to .01 after rotating, it's called run out, apko top pr jahan dial 0 set kia hai mark kr laina chaye and again hub ko exactly usi point Lana chaye to yeh 0.01 ka difference nahi aye ga 0 reading he aye ga. Or how can you alignment without adjusting axial?
Nice, kya aapka number mujhe mil skta hai mujhe pump alignment ka guide chahie..
Right question but ye runout nahi hai o degree mark nhi karne ka parinam hai jise laprwahi ya overconfident kah sakte hain,,
Nice vidio sir ji
Nice presentation brother
Thanks alot bhai for showing this❤❤❤
Aapka video bahut baiya laga sir
Bro very nice very useful video please update alignment sim install & remove full video please please please
Bhai bottom se -04 dikha raha he . Motor ko 2 divission tak tight kiya ja sakta he . To 00 aa jayega. Ya nearabout aa jayega
Very good explain sir
Nice effort👍
Brother housing inside 22211 Ek c3 spherical roller bearing you told ball bearing it's not correct please check it
Sir isme Ball bearing nahi lagahe. Plumber block SNL 511. Spherical roller bearing lagahe 22211 K C3.
Bhai isse kuch ni pta
Very nice sir jee 👏🌹
It was very helpful video for me.
Video aur thoda acha se banaiye
Kuch dikhai nhi diya
Aur axial alignment karke dikhaiye.plz
Accial eppade sim ad panna vendum
Isme ball bearing nhi hota h spherical roller bearing tapered bore hota h
side reading + me aie to bottom ki reading kaise nikalen bine lyea..
सर हमको रिडींग देख के सीम कोनसा डाला जा सके ऐसा विडिओ बनाईये
Very good sir
Is alignment me ,only radial dimension check kiya apne. Axial reading ka required nehi hai??
Please inform me
Ek reading plus me aaaya ek reading minus me aaya thab kya karna kaise adjust karna...
Dusere fiter ko bulana chahiye
😂@@JaswantsinghChouhan-df8zr
Sir aapka WhatsApp no
Sir aapka WhatsApp
Busy
Super sir
👍
क्या आप केम फिगर सम्मिट वीडियो डाल सकतेहो
Hsm side me delay wala motor ek bar alligenment karke dekhau
Sir Bearing ka inter clearance formula kya he, or master levels former kya he, or spring couplings ka misalignment kitna tak chod sakte he sir. Plz replay comment sir. 🙏
Flood caplin ka inlinement ka video bnaiye sar jee.
Me karta hu har cupling ka alaiyment
Nice vdo sir
ball bearing nahi bhai doubble row taper roller bearing hai...
Thank you bro alignment me kitana se kitna ke bich reading hona chahiye bro
Sir Thermal exp kit na rakhe ga
Good job 👌👍 bro
Hi boss i am shahin form bangladesh boss i whant to learn something about dial gauge from you if you teach dial gauge has to small and big cuts like watch tahnks boss
Badiya sir
Rolar bearing hai esme
Good job 👌👍👌 bro
Axial reading ka video banaye
Hii sir mera ye samjh me nahi aata hai ki axial ya rediyal me dekha ja ta hai ki sim kidhar lagaye
Good 😊
Thanks bhaiya
Good
Kolam pe koi video banaye Sir.
Nice brother
Bhai reading is 0.04mm,please correct your explanation you are telling 0.50mm.
Pressure kaise set karte hai dailgauge me
Bhai fan me ball bearing nahi spherical roller bearing hota h
Bhai dubble Row boll bearing bhi lgta h usme koi shakk nhi h
Me har cupling ka karta hu alaiyment
Bhai tu direction hi bta de clockwise or Anticlockwise
Sir hamko full alaiment ka vedio dekha o axial aur Redial dono ka said out aur botom dono ho
Sir alaement me sim kam jyada kar kar dikhaeye
Sir final reading kitna redial
3 mm tak bhi challah hai
Sim kese calculate karke dale bhaiya,batao thoda redial me
Video को पुरा देखो तो जानकारी होगा
@@SanjitFitter❤❤sir
Reitz India make fan?
Nice video bhai aap job kaha krte h
Please mujhe a Kam sikhna hai koi company bataiye please sir please
Water ya masterlavel
00.5ke Ander hona chaiye
- -=+ hota h _3_5=8 hai
Bhai yaha math ka formula nahi lagata hai
Aap Aapne pass mujhe bula kar kam sikha dijiyega sir kyu ki mujhe kam sikhana hai plz sir
Poori vedio to blure m nikal gi
Sir motor ka base frame ka Master level kaise karte hai please batayiye
Iccead frame ko half grouting karne ke baad hi master level kiya jata hai pump ke suction pe master level ko rakh kar dekhen aor base bolt ko tight karen aor frame ke base me leveling ke according shim bhi dena padta hai taki trolence me hi rahe
Gap kitna rakhte h grid coupling me ?
0.85mm
Bhai reading likh rhe wo sahi se nhi dikh rha hai
Iska Sutra kya he bhai
Kha se hai aap bhaiya
वो -0.5mm नही -0.05mm है।
0.5 Nehi - 0.05
Sanjit sir Aapse bat karna hai
पहले kalaint se चेक karalo tabkabhar karna
Rang ailment
Can you please tell what is the axial reading tolerance?
axial tolerance 0.05 से 0.00 तक होना चाहिए
Pump and motor couplings ke bich gap kitna ho skta h..5 mm?
@@Naturelover.21 before adjust the gap between motor and pump, first you must check the coupling spacer size or you said coupling size usky size ky mutabik ap size rakh sakty ho, and agar spacer kay sath shims Hain ya phir gasket use hoti hai uski bhi thickness add krna prti hai
Muhammad shoaib ek baat batao agar right side me reading 0.03 hai toh same hum same side me frame ko hammer kar k zero le ate hai mujhe ek doubt tha ki frame aur foundation me bolt laga hai toh motor age kaise jata hai
Superb ji
reading Nahin likhna aata hai to Kyon dikh raha hai
Shim Calculation ka video banaye sirji.
0.05 reading jada hai
Wrong Bataya Bhai log. 0.02 or kam karna chahiye 😂
Uncorrecte alignment
0.5 aur 0.05Me fark pata hai
Samjhe nahi aya sir
Fitter sab aise hi vedeo banaye aur bhi
Camera man not good
0.5 nahi 0.05 hai vai
Ek bar bat kar lijiyega hamase
Sir reading 0,5 hai 0,05 hai
0.05 hai
You are right ✅️ bro
Kuchh nahi dikh raha
Alignment ka sim calculations bataye
ये गलत कर रहे हो पहले साइड मिलना चाहिए फिर टॉप एंड बोटम देखो
Nahi pehle top bottom fir side aling karte hai 😍😍
Pehle thik se Sikh lo phir video banana thik hai, 2 min ka kaam ko das minutes lagata hai dial gauge ka plunger reading lene aata hai 😅
Reading Rong h
0.05 ke range ma hona chahie
Alignment ka tolerance kitana RAKHATE hai plz bataye
0.05 से 0.00 तक
Bhai ap to only reading batate ho par sim currection kana batao
-0.01 -0.05 = - 0.06 hota hai
Galat hai
Bhaiya aap se bat karni hai phone nambar dijiyega apana
Sir aapka number dio
App ka number bolo bhai
Nice bro, kya aap apna number mujhe de sakte ho mujhe guide chahie please.
Good
Good