Theres a notch on each of the brush holders. If you will take a pick and remove the spring end that is pushing on the carbon brush and set the end of the spring in the notch, you can move the brushes with ease to get them over the bearing of the motor and when it is in place just pop the springs off the notches and they will automatically push against the carbon brushes like they are supposed to. Just a little trick if youre having trouble
Thank you for excellent Video Followed your instructions . first try drill seized immediatly . Found I had not aligned the "bush card" correctly it had seized to the fan . refitted and all is good ...SO anybody doing this fix be sure that all parts are in the right place .... the bushcard groove is very small and easy to misalign.
my milwaukee M18 impact driver is getting weak. it gets right away on the impact and doesn't hit hard at all . it takes way more time to screw a screw... so I opened it . seems to my eye the brushes are still good. they have quite a lot of graphite left..... iyo still could they be defective ? they look perfect to my untrained eye...what to do plz ? ( I did had new grease to the impact part of it ( but it has plenty left )) thank for your help.
i got my brushes replaced within the warranty but in 2022 it’s not under anymore, i think that’s my problem but it wont start if i help it by hand, will see will try as i have brushless now on hand
Dude, you put a house together but don't own a soldiering gun? Jam on it man, it's easier than you think. Nice job on the video, appreciate you taking the time.
Hi I live in VN i have 1 hammer drill MIlwaukee M18 2702 after 2 weeks to work it is smoke and death, but body light on good i was check soldered it is good, please hepl me, because it is expensive . I buy on ebay, i cant go to usa take it back under warrenty
Thank you for the video I got. A. Ridgid r86008 gen 4 fuego the brush assembly looks the same so. I. Can use what. You did. Because. They. Are both manufactured by TTI similar design In ports no one seems to have a video on that ereplacementparts got it where you replace the whole motor which doesn't explain the brush assembly I have done it a tone of Dewalt drills. Carbon brushes and was done just fine only drawback is you need a soldering iron along with soldering paste but in the end it's still way cheaper. Then new I. Was dum in 2014 and did not do LSA warranty on my kit I. Also got the r86034 that's shot the gear case is gone
![Seungmin "그렇게, 천천히, 우리(As we are)" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/kAzmhLHePqU/mqdefault.jpg)
Theres a notch on each of the brush holders. If you will take a pick and remove the spring end that is pushing on the carbon brush and set the end of the spring in the notch, you can move the brushes with ease to get them over the bearing of the motor and when it is in place just pop the springs off the notches and they will automatically push against the carbon brushes like they are supposed to. Just a little trick if youre having trouble
Came here expecting a grizzled old dude. Found a young dude giving a detailed, well edited tutorial. Thanks for the video, my man.
Great tutorial, Ben. Thanks for taking the time to make it!
Thanks from Mexico
Thanks I love my 2 m18's and 1 has bad brushes so I ordered new ones. Good video👍
Thank you for excellent Video Followed your instructions . first try drill seized immediatly . Found I had not aligned the "bush card" correctly it had seized to the fan .
refitted and all is good ...SO anybody doing this fix be sure that all parts are in the right place .... the bushcard groove is very small and easy to misalign.
Always do a good PM while ur in there.
my milwaukee M18 impact driver is getting weak. it gets right away on the impact and doesn't hit hard at all . it takes way more time to screw a screw... so I opened it . seems to my eye the brushes are still good. they have quite a lot of graphite left..... iyo still could they be defective ? they look perfect to my untrained eye...what to do plz ? ( I did had new grease to the impact part of it ( but it has plenty left )) thank for your help.
2611-20 (Milwaukee 1/2 Hammer Drill) When I pull the trigger no Light, no sound. The battery is good. Do you have any ideas?
i got my brushes replaced within the warranty but in 2022 it’s not under anymore, i think that’s my problem but it wont start if i help it by hand, will see will try as i have brushless now on hand
how long were you running the drill for? looks almost new, mine looks like its 10 years old after a month in the shop
good vid, shame you didnt give it a good clean when it was apart ...... next time eh :-)
Well done both info and video.
A can of CRC contact cleaner while everything is exposed would also help if you have the time and money
Ben, you're a top lad m8 👍 Thanks!
Dude, you put a house together but don't own a soldiering gun? Jam on it man, it's easier than you think. Nice job on the video, appreciate you taking the time.
Hi I live in VN i have 1 hammer drill MIlwaukee M18 2702 after 2 weeks to work it is smoke and death, but body light on good i was check soldered it is good, please hepl me, because it is expensive . I buy on ebay, i cant go to usa take it back under warrenty
open it up and look for the problem.. if there was alot of smoke its most likely roasted the motor winders and you can scrap it
Well done
Thank you for the video I got. A. Ridgid r86008 gen 4 fuego the brush assembly looks the same so. I. Can use what. You did. Because. They. Are both manufactured by TTI similar design In ports no one seems to have a video on that ereplacementparts got it where you replace the whole motor which doesn't explain the brush assembly I have done it a tone of Dewalt drills. Carbon brushes and was done just fine only drawback is you need a soldering iron along with soldering paste but in the end it's still way cheaper. Then new I. Was dum in 2014 and did not do LSA warranty on my kit I. Also got the r86034 that's shot the gear case is gone
mijo falto lmpieza general, pulido de colector, cambio rodamientos,limpieza de tarjeta,lubricacion general...mal trabajo
thanks
Quiero cambiar el gatillo interruptor de taladro Milwaukee B54AD08361694
Putting that brushes disc on is a pig. So hard to push those metal things in to put it on.
brush is four dollars on ebay!
Well done