One Mold - Cast Three Ways

Поделиться
HTML-код
  • Опубликовано: 30 сен 2021
  • In this video I use the same silicone glove mold to make a solid resin casting, a hollow rotational resin casting and a wax candle casting.
    Thanks to Tiffany for sending in her project.
    Check out her work at Tiffany of La Baroque Candles on instagram : labaroque_
    Here is a list of suppliers for the rubber, resins and waxes I use in my videos:
    www.dropbox.com/s/kz6mhmf7v5v...
    Do you have a project to suggest for the channel?
    Here’s a .pdf with everything you need to know:
    www.dropbox.com/s/pjb0l6fr7zj...
  • ХоббиХобби

Комментарии • 133

  • @JohnJones-oy3md
    @JohnJones-oy3md 2 года назад +49

    15:45 - Beeswax is like "Whoa, soy wax? So much for loyalty, Robert".

    • @RobertTolone
      @RobertTolone  2 года назад +30

      I felt terrible and spent quality time with my beeswax reassuring it that I wasn’t abandoning it, just following the client’s orders.

    • @KevlarGorilla
      @KevlarGorilla 2 года назад +6

      @@RobertTolone When people keep on telling me to mind my beeswax, this must be what they meant!

  • @y_us_12
    @y_us_12 2 года назад +9

    Tip: cast wax at the lowest possible temperature, that would reduce cracks. Feel free to put a stick into your mold while wax is liquid and mix it to release bubbles.

  • @ramiroiturbe86
    @ramiroiturbe86 2 года назад +12

    Found the channel about a month back and i'm loving all the videos you make! Great personality and a great teacher!

  • @adams.2370
    @adams.2370 2 года назад +31

    Great video! Wax is weird. I've used a couple varieties of sculpting wax. For me, I will preheat the mold, pour, then stick it in a box made of a couple layers of foam insulation that is pretty close to the mold size. The goal being to reduce heat loss and slow the cooling time as much as possible. Before I figured that out, I would have wax castings that would shatter if you looked at them the wrong way from the internal stresses.

    • @ssl3546
      @ssl3546 2 года назад +2

      Can also do multiple pours though lines might be visible on the surface. Or could reheat the mold to consolidate the wax and then do a second pour. I think the wax was poured too hot as well.

  • @jchunick
    @jchunick 2 года назад +35

    I recently discovered this channel and I'm thoroughly entertained and learning a lot of good stuff from the best kind of expert - someone who's worked in the trenches and made all the mistakes and learned and came up with better methods. Great job at presenting the info and being entertaining while doing it! Thanks for your time, effort and knowledge.

  • @Guitargoddess843
    @Guitargoddess843 2 года назад +2

    Resin crafts/ casting crafts are so addictive because it's always a surprise!

    • @SBecktacular
      @SBecktacular 2 года назад

      Yah but I hate spending time and $ on a flop☹️ 😅

  • @helenadawn5
    @helenadawn5 2 года назад +2

    Your method of rotation casting is perfect, I like it !!👍😊
    Greetings from Mexico !!🇲🇽😁

  • @RamoArt
    @RamoArt 2 года назад +22

    It's kind of a shame that the person that printed the bust didn't take the time to sand and fill the layer lines. It was interesting to see a new material though

    • @vfxforge
      @vfxforge 2 года назад +2

      terrible print.

    • @zachchenoweth6622
      @zachchenoweth6622 2 года назад +3

      Agreed.... so much money wasted on a mold for a print that should have been cared more for. Hell, for that size it really should have been SLA printed...

    • @kallymihova6232
      @kallymihova6232 2 года назад

      Good thing is its for candle making, a quick torch will smooth it all :)

    • @AlmightyMister
      @AlmightyMister 2 года назад +7

      Still, why not do a one time proper preparation instead of a bunch of finishes. It's also way better for the mould's lifetime to have a smoother surface finish

  • @CajunCraftastrophe
    @CajunCraftastrophe 2 года назад +5

    Another great video, Robert. It was fun to watch you roto-cast and to see a valiant attempt at wax casting. That wax did look like the problem. Crumbly and weird. Thanks for sharing your wealth of skills with us!

  • @NickToland
    @NickToland 2 года назад +4

    With the wax, i would say try it like a roto cast and then fill it slowly

  • @craigmile7286
    @craigmile7286 2 года назад +2

    hell yeah Rob! never thought id be so stoked for a silicone mold video

  • @clivedurrant481
    @clivedurrant481 2 года назад +1

    This is a great Channel,what a great temperament for failures you have Robert,best lesson I've learnt!

    • @RobertTolone
      @RobertTolone  2 года назад +2

      You can either laugh at or cry about your failures. I would rather laugh and anyway, failure is the best teacher.

  • @fredrikoregard832
    @fredrikoregard832 4 месяца назад

    Great! Awesome! Nice work and thanks for good demonstration!👏😁🙏

  • @truegret7778
    @truegret7778 2 года назад +2

    Its fun watching you work double-time to get the clamps on quickly onto the rotational mold !!
    Thats a challenging mold given the hair rows. And the nature of 3D printing will yield bubbles at the bottom (looks like she didn't print it with supports).
    Great lessons, great outcome. Thanks!

  • @annekabrimhall1059
    @annekabrimhall1059 2 года назад +2

    Such a beautiful sculpture!

  • @Floramycena
    @Floramycena 2 года назад +4

    Maybe put some resurvoires so when it shrinks it can pull the wax from there and hopefully doesn't crack

    • @lucassmith1886
      @lucassmith1886 2 года назад +1

      That's possible. I also heard someone say that pouring the wax in layers helps it to cool and shrink evenly, as of course it will shrink. Someone also suggested that the wax he used was probably too hot, and cooled too quickly as well, causing all of the defects seen in the video.

  • @bustersbashers2280
    @bustersbashers2280 2 года назад +8

    The wax cast, firstly, you poured it too hot 🥵, you need to let it cool to around 50-55,…
    Colour, it’s best to use pigment powder if you are wanting a solid colour, using liquid colour adds too much moisture making the cast soft and brittle. Hope this helps.
    Great videos, Thanks 🙏🏻

  • @MarketResearchReading114
    @MarketResearchReading114 2 года назад +2

    Robert! Thanks for sharing I was waiting to see how this one turned out and the wax was so fun to see. Spheres have a lot of surface area so I'm guessing the head cooled a lot more and at that break in the neck the cooling must have been stunted by the big warm blob of wax in the shoulder area. What a fun thing to see shake out. The rotational mold stuff is really interesting I think that's something people love to see.

  • @tiberiuioan6331
    @tiberiuioan6331 2 года назад +1

    Simply the Best ❤️

  • @massimodeantonis7206
    @massimodeantonis7206 2 года назад

    Mr Tolone thanks for what you are doing, following your videos I finally managed to do my first mould, will open it tomorrow and try casting it in resin. So exciting! Keep it up!

    • @RobertTolone
      @RobertTolone  2 года назад

      Good luck with your project! I hope the castings come out great

  • @cerberus333dog
    @cerberus333dog 2 года назад +1

    on the wax, I would recommend a slip casting. pour and let it set for a while, them pour out the bulk of the wax. This will give you less shrinkage and cracking. also a high plastic wax (like machinable wax) will give better results for wax casting in this manner.

    • @RobertTolone
      @RobertTolone  2 года назад

      All true but this is supposed to be a candle mold.

  • @crain43
    @crain43 2 года назад +2

    Great video Robert! Never expected to the wax to be so brittle and porous.

  • @gordonmorgan3131
    @gordonmorgan3131 2 года назад +3

    heads up, soy wax is a pretty soft wax, most candle waxes are subject to shrinking which is why rigid molds are generally avoided, for a mold like this I reccomend filtered beeswax or paraffin wax as they tend to be more rigid ^^

    • @GH-te6gp
      @GH-te6gp 2 года назад +1

      Great tips! How do you know if beeswax is filtered? Is it related to color like yellow or white? Also is there an eco friendly wax you recommend besides beeswax because it can get expensive.

    • @gordonmorgan3131
      @gordonmorgan3131 2 года назад

      @@GH-te6gp filtered beeswax mostly means primarily raw beeswax thats been through at least 2-4 filtrations to remove any dead insect parts or plant matter, nothing to do with the color really, the color is mostly a matter of processing, the yellow wax being less processed and usually cheaper, that being said, sometimes beeswax simply comes out more yellow or white ^^ paraffin wax has a bigger ecological impact than beeswax or other such similarly natural waxes but does tend to be cheaper in bulk for matters of free standing molded candles, if you're simply putting a candle in a pot (jar) then soy wax will work fine. if you want to skip a big part of the price of beeswax though, you can try looking into local sources such as small business beekeepers and bee stores for raw unfiltered beeswax, the raw stuff generally just needs a couple rounds of at home filtering which is fairly easy to do and much cheaper in the long run with the con of having to do some of the work yourself instead ^^

  • @Visible.Friend
    @Visible.Friend 2 года назад

    So much fun hanging out in your shop!

  • @josemariacajica9824
    @josemariacajica9824 2 года назад +1

    Truly this is such a wonderful channel and content. I cannot express how amazed I am by the work and dedication of this video. Due to past personal experiences, I was under de impression that all artists kept a tight lock on their techniques and secretes. However, videos as this one proven quite the opposite. For such reasons I am truly grateful and although I may not contribute as much to the creation of this content, I will not forget to due my contribution.

    • @RobertTolone
      @RobertTolone  2 года назад +1

      I didn’t invent any of the things I demonstrate on the channel. Just using good practices as recommended by the material suppliers and manufacturers. So I’m not giving away any trade secrets! 😀

    • @josemariacajica9824
      @josemariacajica9824 2 года назад

      @@RobertTolone 😁Yes, but you have no idea how encouraging your videos are! Thanks a lot!

  • @Krenshondizerkhan
    @Krenshondizerkhan 2 года назад

    Thanks for sharing all your knowledge, 🤍

  • @TheDarkArtist66
    @TheDarkArtist66 2 года назад

    Your videos are awesome my good man. I have just recently got onto molding and casting after being frustrated with not being able to paint my monster clay sculptures. I know, someone is going to tell me that I can which I know but its not there same as having something that's solid and permanent. Thanks so much for the lessons and taking out the guess work. Your amazing

    • @RobertTolone
      @RobertTolone  2 года назад

      Glad you find my videos to be helpful Donnie. Thanks for watching!

  • @Guitargoddess843
    @Guitargoddess843 2 года назад +1

    I think with wax it's always best to pour in layers so it cools evenly and won't shrink as much (because it will shrink as you go)

  • @zrebbesh
    @zrebbesh 2 года назад +1

    Wax is hard to work with. It always shrinks. It's granular if it cools too fast and has cracks if different parts cool at different rates. And it often as not pulls away from the mold while it's shrinking. It might work to build it up in layers from the surface in by hollow-casting, then hollow-casting again when it's cooled just enough to be solid (but still warm enough that melted wax will stick to it). I dunno. Haven't tried it. But wax is hard.

  • @sujaijanardhanan954
    @sujaijanardhanan954 2 года назад +1

    You can add little bee wax while so it don't break

  • @runin1wild149
    @runin1wild149 2 года назад +1

    That was pretty interesting! Really enjoyed this video, loved the fast forward on spinning the mold had a good laugh.
    Now back to the slip shade? I was wondering if we’ll ever see the final episode. I gave up on the clear bulb a while back ... yeah my OCD is kicking in. 😂

    • @RobertTolone
      @RobertTolone  2 года назад +1

      Final video on that series will appear this Friday. It’s been a journey…

  • @TonyMiller.13
    @TonyMiller.13 2 года назад

    👷🏽 i found your channel by the Crafsman Steady Crafting... Great content my man

  • @jordanhindes769
    @jordanhindes769 2 года назад +1

    Great video. Your soya wax was probably too hot and cooled too quickly. Amazing hollow and solid cast though !! Liked seeing a different technique.

    • @RobertTolone
      @RobertTolone  2 года назад +1

      I think that’s right about the wax.

  • @hanelyp1
    @hanelyp1 2 года назад +2

    Casting wax:
    - use a double boiler to melt the wax. Good temperature control.
    - was SHRINKS. You'll need a feeder to supply material to the mold as it cools.
    - The neck will be a problem spot, tending to solidify first, This will be a serious problem if the head can't pull away from the mold to stay with the neck. Pre-heating the head part of the mold could make this worse.
    - I've never seen wax that brittle. But I've never used soy wax.

    • @RobertTolone
      @RobertTolone  2 года назад

      Every trade has it’s rules. Wax is not resin. My inexperience showed.

  • @jaicobbenton5490
    @jaicobbenton5490 2 года назад

    Hi Robert is there any videos where you cut the rototcast product on the bandsaw so we can see the wall thickness. Thanks for another great video

  • @Guitargoddess843
    @Guitargoddess843 2 года назад

    But what if i said.... Your speed is just right 👍🤣❤️

  • @fuujii6390
    @fuujii6390 2 года назад +2

    Ah that's a shame about the wax cast, it would've looked lovely with that color, great video either way!

  • @janika2356
    @janika2356 2 года назад +2

    Soy wax isn't really the best wax to get good casts out of. I would suggest going for a parrafin / stearin mix and topping it up as you go.

  • @Jlynn2303
    @Jlynn2303 6 месяцев назад

    Very nice - but as an absolute beginner it would be very helpful if you named every product you are using in the video as well as posting a list. It would also be wonderful if all videos were painfully well La eked if they are in a sequence. I watched part 1 of one of your series and am looking everywhere for part 2! There are numerous multiparty instruction videos and it is not always easy to tell which part 2 goes with which part ! Thank you!

    • @RobertTolone
      @RobertTolone  6 месяцев назад

      Here is the prequel to this video: ruclips.net/video/96kPgjU7LFk/видео.htmlsi=T0ptSRxs81iwa_TS

  • @mickybetts7957
    @mickybetts7957 2 года назад +1

    Interesting experiment. I wonder if the wax casting would shrink and crack if it were filled and poured out repeatedly building up a hollow casting? I've seen candles being made and the wick gets dipped repeatedly to build up thickness of wax. Maybe a casting would work similarly in reverse?

  • @annekabrimhall1059
    @annekabrimhall1059 2 года назад +17

    Try paraffin wax. Soy wax is temperamental.

    • @hanelyp1
      @hanelyp1 2 года назад

      I've never worked with soy wax. But I have worked with paraffin a fair amount, and never seen it nearly that brittle. I was also taught by my mother to always use a double boiler melting wax for temperature control.

    • @GH-te6gp
      @GH-te6gp 2 года назад

      Is there an eco friendly wax alternative you recommend if soy wax is bad for this?

    • @annekabrimhall1059
      @annekabrimhall1059 2 года назад

      @@GH-te6gp I don’t know of any other natural wax that works as well as paraffin.

  • @danje748
    @danje748 2 года назад

    Looks like this type of candle wax was vastly interior to the type you had the last time. But it was very interesting to see. And kind of strange to see the wax revert to that granular state despite being melted and poured as a solid piece.

    • @RobertTolone
      @RobertTolone  2 года назад +2

      Probably a temperature thing. But I’m definitely not a candle maker so I don’t really know.

  • @custos3249
    @custos3249 2 года назад

    Seems like there's a range of options for the soy wax - more controlled cooling, pouring in stages, pouring around a core, etc. that'd make it serviceable. Hell, it'd be interesting to see if merely reheating the exterior of the mold enough to melt a significant amount of the outermost wax would be enough.

    • @RobertTolone
      @RobertTolone  2 года назад +2

      The results reveal my inexperience with that material. The fun part of my RUclips channel is that I get to do things that I would never do on a job for a client. With client work I always use materials and processes that I have tested over and over and found to be reliable. On RUclips I am often playing with materials I’m unfamiliar with. The channel is all about learning. Experimenting (and failing) is a great way to learn!

    • @custos3249
      @custos3249 2 года назад

      @@RobertTolone I've only a basic understanding from an engineering mindset and always heard wax can be a major pain, especially as you venture away from paraffin.
      It'd be pretty cool to see more experiments if you feel interested. I've always wondered if wax could be used (and if it offers any distinct advantages over other methods) in resin casting. Specifically, if the temp of the curing resin could be kept low enough/melting point of the wax made high enough, could you use the lost wax method turned on its head? Rather than melting out the core, you melt away the mold. Probably already a better method out there with far fewer steps, but seems like it could be useful for casts with voids and hollows that'd otherwise trap silicone.

    • @RobertTolone
      @RobertTolone  2 года назад

      @@custos3249 Mold making and casting is a vast universe and within that world my area of expertise is silicone molds and urethane resin. I don’t know where this channel will take me; it’s an experiment and a journey. Should I wander off into different materials and processes or stick to what I know? The audience is my guide; they vote with their views.

    • @custos3249
      @custos3249 2 года назад

      @@RobertTolone As someone who's studied the mind for about a decade and focused on creativity, all I've to say is: always experiment! Granted, I say that since you give clear indication you value the learning experience. I'd certainly enjoy seeing various types of tests to see if the properties of wax could aid or complement resin casting. If you want to get scientific, I'd bet it might be possible to calibrate the waxes contraction rate that, as it cools, it offsets what will be the contraction in the resin. Perhaps it's a longshot, but could make producing functional copies more tenable it if works/could be further developed.

  • @mraide
    @mraide 2 года назад

    Do you think it maybe to much pigment in the wax?

  • @jameswilkins288
    @jameswilkins288 2 года назад

    love watching , was wondering i have a part on a 2 way radio that no longer available could i send you the part and see if you can copy it thanks for any help

    • @RobertTolone
      @RobertTolone  2 года назад

      Send pics to roberttolone@yahoo.com

  • @brianlindsay9097
    @brianlindsay9097 2 года назад +1

    Amazing!
    I have seen people do rotational casting by simply rolling the mold around in their hands. I'm sure there are lots of reasons why this method is inferior to the way you do it, but in your opinion is it viable for someone like myself who isn't hardcore enough to build a giant wooden gimbal? : )

    • @RobertTolone
      @RobertTolone  2 года назад +2

      Sure, it works. We used to do it that way but building a machine is quick and it makes hand rotocasting much easier!

  • @madtabby66
    @madtabby66 2 года назад

    I’m not going to say you’re going to fast or to slow, but what about a handle, like a window handle so you can just sit and spin?

  • @j0hnf_uk
    @j0hnf_uk 2 года назад

    I'm no expert, but I would imagine wax needs to cool down very gradually in order to avoid shrinkage, also, having some kind of feeder at the top of the mould to allow the wax to draw down once it does start to set, would be a good thing.

    • @madtabby66
      @madtabby66 2 года назад

      I used to make candles. Shrinkage happens, I used to just keep back a bit and as it solidified, top up.

  • @roger.agburn
    @roger.agburn 2 года назад

    Lovely video. =)
    Thinking about candles, wouldn't you want the mold to be open on the top of the head, so you can let the wick stick out on the top of the candle?
    Would that have been an option for this particular mold? (I mean ... of course you have to decide: Nice top for resin casting, of nice spot for the wick for candle casting.)

    • @RobertTolone
      @RobertTolone  2 года назад

      Normally you would use a wicking needle to push the wick through the rubber mold. I dispensed with that because I didn’t want to put a hole through the mold. Tiffany will decide where she wants to put the wick. Anyway, I’m a casting channel, not a candlemaking channel.

    • @roger.agburn
      @roger.agburn 2 года назад

      @@RobertTolone After I wrote it, I also thought if it can't just be pushed through the rubber. ^_^'
      I just wasn't sure if multi-purpose molds are a good idea or not. But I also don't see myself casting candles in the near future. ;)

  • @TalkingGIJoe
    @TalkingGIJoe 2 года назад +1

    as slow as the resin flows, it seems the rotational and random movements are too fast to actually have the resin flow out evenly to all areas...

  • @jamesrickel3814
    @jamesrickel3814 2 года назад

    Hi Robert, I have a question. I one saw a video about blenko glass where they were using wood molds and blowing glass to the mold, sort of like blow molds do with plastic. Is there a process of blowing plastic like this that can be done at the home level?

    • @RobertTolone
      @RobertTolone  2 года назад

      In theory you could modify a vacuum forming set up for blow molding. I have never seen anyone do that but I suppose it would be possible.

    • @jamesrickel3814
      @jamesrickel3814 2 года назад

      @@RobertTolone Oh dang that is a great idea !!!

  • @tjthomas01
    @tjthomas01 2 года назад +1

    time for a cordless

  • @predar
    @predar 2 года назад

    do you have experience/opinions on using syringesto inject silicon moulds for small resin castings. im generally getting good results although sometimes with unexpected bubbles

    • @RobertTolone
      @RobertTolone  2 года назад

      I never bother with syringe injection. I usually use gravity feed, even with small parts.

  • @kevinwallis2194
    @kevinwallis2194 2 года назад

    blame the wax. I made a lot of candles, and love using gel wax or normal wax.

  • @merrillalbury8214
    @merrillalbury8214 2 года назад

    How about vibrating the mold to reduce bubbles catching

    • @RobertTolone
      @RobertTolone  2 года назад

      Here’s my take on that subject:
      ruclips.net/video/aLpDkHt1gY8/видео.html

  • @christianstorm8854
    @christianstorm8854 2 года назад

    What wax do you use when covering an object and not wanting it to stick when removing and where can it be purchased.

    • @RobertTolone
      @RobertTolone  2 года назад +1

      I always use melted beeswax and it is sold in solid, flake or pellet form in lots of places online.

    • @christianstorm8854
      @christianstorm8854 2 года назад

      @@RobertTolone ok I found a yellow block at Michael’s but they said it was for making candles. Is there a difference?

    • @RobertTolone
      @RobertTolone  2 года назад

      @@christianstorm8854 Should be fine if it is pure beeswax and not a wax blend.

  • @sebozwierz
    @sebozwierz 2 года назад

    Why don't you use filles for such a mass castings? You could save a lot of resin...

  • @jimmyjames1807
    @jimmyjames1807 2 года назад

    i thought the artist would have fixed there model, you can see all the layer lines

  • @Cvshmere
    @Cvshmere 2 года назад

    How can I hire you for something like this?

    • @RobertTolone
      @RobertTolone  2 года назад +1

      My RUclips channel has become a full-time job and I am only working on channel projects these days.

  • @dfutubetest
    @dfutubetest 2 года назад

    HI, I have been doing molding and casting for a couple years. I love the channel and have learned a great deal. As it happens I am about to launch a non-profit organization that will be creating public art projects honoring the women and men of EMS for their service. These will be based on lifecasts of EMS personnel's hands. I emailed you to discuss possibly collaborating with us. I have no clue how many emails you get so thought I would also leave this comment. If you didn't see the email please let me know and I will send it again. It came from The Caring Hands Project.

  • @danje748
    @danje748 2 года назад

    It just struck me, your most hated movie must be the 1980 movie Flash Gordon. Simply because "flash, savior of the universe". And as a mold maker I assume that just rubs you the wrong way. ^^

  • @DeadFront1319
    @DeadFront1319 Год назад

    @6:08, ahhhh yes, just the way I like my women...wait what!😆😆✌

  • @MrQuickLine
    @MrQuickLine 2 года назад

    7:29 - don't you mean HOLDY MOLDY?

  • @dustinf11
    @dustinf11 Год назад

    That cradle just seems like its overcomplicating the process. Can't you do this by hand? I've had decent success just holding it.

  • @bethelgues3918
    @bethelgues3918 2 года назад

    Hmmm bee's wax, doesn't shrink as bad. It probably would've done that job better.

    • @RobertTolone
      @RobertTolone  2 года назад +1

      I am pouring beeswax into candle molds this week. We shall soon see if I get a decent result…

  • @glenfisher728
    @glenfisher728 2 года назад

    Like those new camera angles looking down . Got to be more careful handling that melted wax mate , one slip and it's in your lap. Where's your crock pot ?

  • @johndix6101
    @johndix6101 2 года назад +1

    Some people need to watch and learn instead of trying to tell an expert how to suckered eggs 🥚

  • @criticallook5162
    @criticallook5162 2 года назад

    Too many drops of lavender.!??
    :

  • @JohnJones-oy3md
    @JohnJones-oy3md 2 года назад

    1:43 - Oh boy, here come the comments. LOL

    • @chartle1
      @chartle1 2 года назад +3

      The wires are going to attract free energy electrons and screw it up. Only way to stop it is to spin it opposite the spin of the earth. But in Australia with the spin. 👍

    • @chartle1
      @chartle1 2 года назад +2

      Silliest comment I could come up with on such short notice. 🤣

  • @Tobias3800
    @Tobias3800 2 года назад

    maybe too much pigment?

  • @rxz4140
    @rxz4140 2 года назад

    If I sculpt a wax toy, can you make a hard copy for me? I'll pay.

  • @jst1man
    @jst1man 2 года назад

    It's wax.. This happens.

  • @levinebette15
    @levinebette15 2 года назад

    Who are the 5 haters?

  • @SBecktacular
    @SBecktacular 2 года назад +1

    I keep thinking you’re in a laundromat 🥴

  • @ArcticFlies56
    @ArcticFlies56 2 года назад

    Bob, all I can say is, wow. The candle material is definitely not right. There could be a double problem here. The type of wax vs the die. May you should have tested them before using them together. What does the customer say? She is a candle maker, right? Pouring liquid wax into a mold is a normal process for candle making. Maybe your mold material isn’t copacetic with the wax. Maybe there was some resin product left inside the mold which created chemical reaction when you poured in the wax. Maybe, maybe, maybe! No idea!

    • @RobertTolone
      @RobertTolone  2 года назад

      The mold rubber shouldn’t be a problem. it was most likely a temperature issue. I’ve never used soy wax before so I would have to experiment with it, which I am not going to do because I’m a resin guy, not a candle maker! 😊

    • @ArcticFlies56
      @ArcticFlies56 2 года назад

      I don’t know Bob. I think your cutting yourself short. I’m pretty sure that you could do just about anything you wanted to do.