i had 2 bad hall sensors, i removed "good" 680 ohms from one unit, and the bad from the other and was able to get a working sensor from the operation. my guess is large laundry loads putting a strain on those esistors (depending on the direction the drum is turning) and once they open from high heat, your done, but really not hard if you know you to R&R SMT resistors. great video here, gave me the confidence to give it a try and my LG washer is working again. just measure across each of the resistors, it obvious if they are good or bad even while in circuit. GL all
thank you very much, i fixed my washing machine 12/22/2020 using your video. I repaired the faulty sensor with a 320ohm resistor. Thank you very much and have a nice Christmas to my friend
Thanks this was exactly my problem. No error code on machine, just motor was making very weird sounds and not turning properly. I thought it was bad bearings, then bad computer controller, but finally it was just bad speed sensor! Thanks
This helped fix the machine until I get my new hall sensor tomorrow. First I measured my board thinking the same two resistors would be toast -- My two bad 680ohm resistors were in the middle of the PCB board next to the single capacitor, not the ones on the opposite side of the connector.
Ha! Amazing... I had no idea the encapsulation was so poor. It pulled right out. Same issue with mine, replaced with a pair of nice big 680 ohm thru hole just like yours. I suspect it will last years more compared to those tiny 681 SMT resistors. Thanks again!
I asssume the so called RO means "resistor output", output resistor. I assume if you are gonna have this RO thing, then there must be an RI ones too. Isn't that the lingo of the inner circle, you know the separate the educated from the rest?
Hello my friend I need your help In addition to the resistors I have a damaged capacitor, can you give me the values to replace the capacitor? I appreciate your help
All of my Resistors R015, R025, R035, R045 are (smd 681) 681 Ohms. - I wanted to ask that why did your Resistor R045 measure 340 Ohm (It should measure 340 if you have short circuited both resistors to make parallel connetion)? - WHile soldering did you short circuit the R015 with R025? If not then where does your external resistor connects? Thank You
I changed the values of 2 680 ohm resistors because they changed. it worked after all. Thank you for this good information. 🙋♂
i had 2 bad hall sensors, i removed "good" 680 ohms from one unit, and the bad from the other and was able to get a working sensor from the operation. my guess is large laundry loads putting a strain on those esistors (depending on the direction the drum is turning) and once they open from high heat, your done, but really not hard if you know you to R&R SMT resistors. great video here, gave me the confidence to give it a try and my LG washer is working again. just measure across each of the resistors, it obvious if they are good or bad even while in circuit. GL all
Hi thank you. Don't forget to like & subscribe. HHH
thank you very much, i fixed my washing machine 12/22/2020 using your video. I repaired the faulty sensor with a 320ohm resistor. Thank you very much and have a nice Christmas to my friend
Thank you, i so happy this video can help fixed your problem. God bless you.
Thanks this was exactly my problem. No error code on machine, just motor was making very weird sounds and not turning properly. I thought it was bad bearings, then bad computer controller, but finally it was just bad speed sensor! Thanks
Thanks for feedback.
This helped fix the machine until I get my new hall sensor tomorrow. First I measured my board thinking the same two resistors would be toast -- My two bad 680ohm resistors were in the middle of the PCB board next to the single capacitor, not the ones on the opposite side of the connector.
Ha! Amazing... I had no idea the encapsulation was so poor. It pulled right out. Same issue with mine, replaced with a pair of nice big 680 ohm thru hole just like yours. I suspect it will last years more compared to those tiny 681 SMT resistors. Thanks again!
Good luck and success to everyone
Al-Jarjawi, automatic washing machine surgeon
Perfect. Work with 330 ohm
Thanks very much for sharing, totally fixed my issue!
Thank you.
Este adevarat, motorul mergea sacadat , am pus o rezistenta si masina merge. Multumesc
لو أنه الفيديو عربي لكن روعه فنان
Спасибо, добра тебе!
Thank you.
Thank you sir!
Thanks, really great, congratulations
Thank u so much sir God bless u
Thanks welcome sir. Don't forget to subscribe,
Dear sir i test the hall sensor like you between sb and vcc read 30 k ohm and between sa and vcc read 10 k ohm where the problem please answer me ?
great video
معلم ❤
Will this fix work for any LG machine?
No. The same tipe may not fix. But you can try this way. Thank you.
Maaf pak bisa diperjelas posisi solder resistornya? Dibagian mana saja?
Goooood EN
Amigo ..cuando falla el sensor hall en una lavadora que es lo que ocasiona?
No esprime ni hace mucho y aparece envsu pantalla LE error
Ponle la resistencia de 320 ohms vy listo, yo le puse una de 284 ohms y funciono
I asssume the so called RO means "resistor output", output resistor. I assume if you are gonna have this RO thing, then there must be an RI ones too. Isn't that the lingo of the inner circle, you know the separate the educated from the rest?
Is it available online?
Yes, it is available at my country. Indonesia.
Respect
Спасибо большое
Samsung wf861 front load PCB me hall sencer connection कैसे चैक करते है
Hello my friend
I need your help
In addition to the resistors I have a damaged capacitor, can you give me the values to replace the capacitor?
I appreciate your help
Dear friend. I am sorry, i don't know that value of the capacitor.
All of my Resistors R015, R025, R035, R045 are (smd 681) 681 Ohms.
- I wanted to ask that why did your Resistor R045 measure 340 Ohm (It should measure 340 if you have short circuited both resistors to make parallel connetion)?
- WHile soldering did you short circuit the R015 with R025? If not then where does your external resistor connects?
Thank You
Yes the all resistor are smd.
I just follow original resistor spec and combination of soldering component. Thank you
Did u connect the ends of R015 and R025 together??
Thank u for the reply
@@farazafzl yes, i connect pararel the 2 resistor. Thank you.
Tanks very much vous ete un génie merci beaucoup
RATE OF PRICE
Suaramu ketutup backsound pak😥😥
Iya hhhh.
Berapa nilai kedua resistor tsb? Gan. Trim's
Ada di video gan. Trimakasih
Ok!
Klo tidak bisa terputar kiri bagian mananya yg disambung resistor??
Cek modul mainboardnya. Mungkin ada jalur yg putus .
@@hariserviceelektronik4574 tp sy cek kode errornya LE bang
@@asmiatimasyhudah1087 coba ganti resistor seperti pd video.
R u from India? 😁
No. I from Indonesia. Thank you.
Plees sir from the pin which nomber from the pin to which component sir thanks
Pleace watch this ruclips.net/video/BJGBddJ5AtQ/видео.html.
Componet replace= Resistor
Thank you.
hello you can help me please for resistance RO1s and RO2s I have 683 ohm but R03s and R04s i have 340 ohm
You can try to change R01 to R02 with resistor 340 ohm.
In this video i use pararel resistor 680 ohm.
Yes thanks i have removed r01 et r02 and put 2 News 680 ohm and work it thanks again !!!
Cool
Thank you
resistornya itu ada ukuran berapa watt nya kah ??
Untuk wattnya yg kecil masih bisa. 1watt bisa.
Artist
ini yg diseri resistor ukuran berapa ya?
Dah lupa coba cek lagi Di video ada keterangan nya.
y
is this music 🎶Channel?????????????????
just fast forward to 7.12
Привет! как с ковидом? вирусом-12 В датчике Сгорели 2 резистора в датчике холла! Давай дружить каналами! Подписываюсь.
Hi thank you for your attention. But i am sorry, i don't know what did you say. Can you write in inglish!
@@hariserviceelektronik4574 How do you deal with the disease?COVID
@@Изреальнойжизни Just follow intruction from my govermen.
@@hariserviceelektronik4574 I see, good luck! do not get sick, I will go to the channel!
Where it for buing
You can buy at online shop.
Bos minta nmr wa nya 🙏🙏🙏
@@hariserviceelektronik4574 bos bantu saya punya keluhan mesin cuci LG 16kg 🙏🙏🙏
New hall sensors cost $10. Not worth the time to repair them.